Kanomax Anemomaster Lite User manual

Userʼs Manual
LITE
MODEL6006
Handheld Anemometer
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

i
Important Safety Information
The symbols for the warnings used in this manual are defined below.
Classifications
Danger: To Prevent Serious Injury or Death
Warnings in this classification indicate danger that may result in
serious injury or death if not observed.
Caution: To Prevent Damage to the Product
Warnings in this classification indicate ris s of damage to the
product that may void the product warranty if not observed.
Description of Symbols
△This symbol indicates a condition that requires caution (including
danger). The subject of each caution is illustrated inside the triangle
(e.g. the high temperature caution symbol is shown on the left).
This symbol indicates a prohibition. Do not ta e the prohibited
action shown inside or near this symbol (e.g. the disassembly
prohibition symbol is shown on the left).
●This symbol indicates a mandatory action. A specific action is given
near the symbol.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

ii
Danger
Never bring the probe close to a flammable gas atmosphere.
The heated sensor may cause a fire or explosion.
Never touch the sensor.
The sensor is heated during operation. Touching the heated sensor
may cause burns, and may also damage the sensor itself.
Do not disassemble or heat the batteries, or put them into a
fire.
This may cause burns and the batteries may burst.
Caution
Do not use the instrument in a water vapor atmosphere.
Condensed steam on the sensor will change the heat dissipation rate,
resulting in inaccurate measurements. It may also cause damage to
the sensor.
This instrument is designed to be used in an environment with
a clean air stream without any dust or foreign materials.
Foreign materials may cause damage to the sensor. Also dust or
foreign materials on the sensor will impede accurate measurements.
Do not apply force to the sensor.
If the sensor is deformed, the accuracy of the sensor may be
affected.
When measuring, ensure that the direction mar is facing into
the airflow.
Otherwise, the measurement may be inaccurate, as some sensors
(uni-directional probes) have a specific directivity.
Do not use or leave the instrument in a high temperature,
high humidity or dusty environment. Do not leave this
instrument under direct sunlight for a prolonged period.
The instrument may not function properly out of the specified
operating conditions.
Forbidden
Hot surface
Don’t touch
Explosive
Use properly
Forbidden
Set up properly
Forbidden
Forbidden
Forbidden
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

iii
Do not subject the instrument or the probe to strong impacts.
Dropping the unit or placing heavy objects on it may cause damage
or malfunction to the instrument.
Never disassemble, modify or repair the product.
Failure to observe the above may cause short circuit and/or other
failure that will affect the performance.
Do not pic up or carry the instrument by the probe cable.
It may cause a malfunction or the wire may brea .
Remove the batteries from the battery compartment when
storing the instrument. Do not leave exhausted batteries in the
battery compartment. When inserting batteries be sure to
insert them with the polarity facing the correct direction.
Failure to do so may cause battery lea age.
Do not wipe the instrument with a volatile solvent.
The body may deform or deteriorate. Use a soft dry cloth to remove
stains. If stains persist, soa the cloth in a neutral detergent and
wipe the instrument with the soft cloth. Never use volatile solvents
such as thinner or benzene.
Discharge any built-up static electricity from your body before
touching the instrument.
The built-up static electricity may influence the readings and cause
damage to the circuit.
Regularly chec the head of the probe for contamination.
Impurities (such as dust) on the sensor may affect the
accuracy of the measurements.
To get rid of dust, use a blow blush for cameras to blow it off, or you
can rinse it with water and allow it to air-dry completely.
*Be sure to turn the power off before you clean it.
*Never dry the probe with heat. (Heat may cause permanent damage
to the sensor.)
Do not remode
l
/
disassemble
Electrified
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Use properly
Use properly
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

iv
Do not move the main unit and the probe from a cold place to
a warm place quic ly. It will cause dew condensation.
Even when used in an environment within the specified operating
temperature and humidity, a sudden temperature change may
cause condensation. Condensation generated on the sensor may
cause inaccurate measurements. Condensation on metal parts may
cause rusting and lead to a malfunction.
Do not touch the LCD screen with a sharp-pointed object or
with excessive pressure.
It may cause distortion of the screen or a malfunction. Also a rapid
temperature change may cause a malfunction of the screen.
When storing the instrument, put the instrument in the
carrying case and eep it in a place with an ambient
temperature of -10 to 50°C and no condensation.
Do not dispose of the instrument as a household waste.
Please note that the disposal of the instrument and the batteries
should be in line with your local or national legislation. For details,
please contact your local distributor.
Set
up
p
roperly
Forbidden
Forbidden
Forbidden
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

v
Table of Contents
§ 1 Part Names and Functions (Instrument) ....... 6
Part Names and Functions (Main Body) ............................... 6
Part Names and Functions (Probe) .................................... 7
§ Preparation for Measurement ........................ 7
Installing Batteries .......................................................... 7
Battery Level Indicator .................................................... 9
Changing Units for the Readings ....................................... 9
§ 3 How to Measure ........................................... 10
§ 4 Specifications .............................................. 11
§ 5 Troubleshooting .......................................... 1
§ 6 Compensation of Air Velocity Value ............. 13
§ 7 Warranty and After Service ......................... 14
Kanomax Limited Warranty ............................................. 14
§ 8 Contact Information .................................... 16
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

6 Part Names and Functions (Instrument)
§ 1 Part Names and Functions (Instrument)
Part Names and Functions (Main Body)
＜Side＞ ＜Front＞ ＜Back＞
Power/Function Switch is a multifunction switch that can be slid up and
down, and pressed.
1. Pressing will switch the power on and off. Press and hold the switch
for more than 1 second until the LED indicates the change of the
ON/OFF status.
2. Sliding the switch down will change the measurement mode in the
following order: FAST  SLOW  Air Temperature  FAST
3. Sliding the switch up will hold the display. Slide up, down or press
the switch to continue.
＜
Enlarged view of the Power/Function Switch
＞
3. Pause
ON/OFF
1. Press and hold for more than 1
second.
2. FAST/SLOW/Air Temperature
Battery Case
Power/Function
Switch
Display
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

Preparation for Measurement 7
Part Names and Functions (Probe)
§ 2 Preparation for Measurement
Installing Batteries
Use four AA size batteries.
Ma e sure that the power is off before inserting the batteries.
If you are using charging batteries, charge them with a special
*Air Velocity/Air Temperature
(temperature compensation)
sensors are built in.
*During measurement, the whole
surface of the sensor should be
exposed to the wind.
*Face it windward
Air Temperature
(temperature
compensation) Sensor
Air Velocity Sensor
Directional Point
Sensor
Grip
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

8
Preparation for Measurement
Preparation for Measurement
Preparation for Measurement
charger prior to use.
＜
Back (Battery Case)
２
１
３
４
Preparation for Measurement
charger prior to use.
Back (Battery Case)
3.
4.
２
４
charger prior to use.
Back (Battery Case)
＞
1.
Slide the cover of the battery case down
along the rail.
2.
Slide the cover until
up.
3.
Insert the batteries in the order shown in
the left figure, observing polarity.
4.
Replac
reversed
To put the battery cover bac ,
do not
at the top end.
Follow the above
procedure bac wards to s
t
he cover bac
If you forc
cover
be bro en.
Slide the cover of the battery case down
along the rail.
Slide the cover until
Insert the batteries in the order shown in
the left figure, observing polarity.
Replac
e the battery cover by
reversed
procedure
To put the battery cover bac ,
do not
first engage the detent
at the top end.
Follow the above
procedure bac wards to s
he cover bac
If you forc
ibly
cover
onto the body, it
be bro en.
Slide the cover of the battery case down
Slide the cover until
it stops
Insert the batteries in the order shown in
the left figure, observing polarity.
e the battery cover by
procedure
s 1 and 2
To put the battery cover bac ,
first engage the detent
at the top end.
Follow the above
-
mentioned
procedure bac wards to s
he cover bac
.
ibly
try to clic
onto the body, it
Slide the cover of the battery case down
it stops
, and then lift it
Insert the batteries in the order shown in
the left figure, observing polarity.
e the battery cover by
following the
s 1 and 2
.
To put the battery cover bac ,
first engage the detent
mentioned
procedure bac wards to s
lide
try to clic
the
onto the body, it
may
Slide the cover of the battery case down
, and then lift it
Insert the batteries in the order shown in
following the
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

(More than 4.6V
Batt
ery Level Indicator
Battery l
evel

Guaranteed operating voltage range of the battery is more than
4V.

When battery voltage decreases to less than 4V, the display will
go on and off and

When you are using
little
Ch
anging Units for the Readings

The units can be changed using the
dip switch.

You can find the dip switch in the
battery box.
(More than 4.6V
Sufficient
*
SW 2
ery Level Indicator
evel
is displayed as
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
go on and off and
When you are using
little
early, before the 4.3V
anging Units for the Readings
The units can be changed using the
dip switch.
You can find the dip switch in the
battery box.
(More than 4.6V
）
(4.6V
Sufficient
is not used
ery Level Indicator
is displayed as
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
go on and off and
the
power will be turned off automatically.
When you are using
a charging
early, before the 4.3V
anging Units for the Readings
The units can be changed using the
You can find the dip switch in the
(4.6V
- 4.3V
）
M
is not used
.
1 2
ON
Preparation for Measurement
is displayed as
below
depending on the charge left:
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
power will be turned off automatically.
a charging
battery, recharge the battery
early, before the 4.3V
-
4.0V mar
anging Units for the Readings
The units can be changed using the
You can find the dip switch in the
(4.3V
–
M
e
di
u
m
Units
SW No.
m/s
FPM
1 2
Preparation for Measurement
depending on the charge left:
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
power will be turned off automatically.
battery, recharge the battery
4.0V mar
is displayed.
The units can be changed using the
You can find the dip switch in the
(Lower than 4.0V)
Blin ing of the indicator
–
4.0V
）
SW No.
°C
°F
OFF
Preparation for Measurement
depending on the charge left:
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
power will be turned off automatically.
battery, recharge the battery
is displayed.
(Lower than 4.0V)
Blin ing of the indicator
Replacement of
Batteries
１
OFF
(
factory default
ON
Preparation for Measurement
9
depending on the charge left:
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
power will be turned off automatically.
battery, recharge the battery
a
(Lower than 4.0V)
Blin ing of the indicator
Replacement of
Batteries
factory default
)
9
Guaranteed operating voltage range of the battery is more than
When battery voltage decreases to less than 4V, the display will
a
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]