Kanomax ANEMOMASTER LITE 6006 User manual

i
Important Safety Information
The symbols for the warnings used in this manual are defined below.
Classifications
Danger: To Prevent Serious Injury or Death
Warnings in this classification indicate danger that may result in
serious injury or death if not observed.
Caution: To Prevent Damage to the Product
Warnings in this classification indicate risks of damage to the
product that may void the product warranty if not observed.
Description of Symbols
△This symbol indicates a condition that requires caution (including
danger). The subject of each caution is illustrated inside the triangle
(e.g. the high temperature caution symbol is shown on the left).
This symbol indicates a prohibition. Do not take the prohibited
action shown inside or near this symbol (e.g. the disassembly
prohibition symbol is shown on the left).
●This symbol indicates a mandatory action. A specific action is given
near the symbol.

ii
Danger
Never bring the probe close to a flammable gas atmosphere.
The heated sensor may cause a fire or explosion.
Never touch the sensor.
The sensor is heated during operation. Touching the heated sensor
may cause burns, and may also damage the sensor itself.
Do not disassemble or heat the batteries, or put them into a
fire.
This may cause burns and the batteries may burst.
Caution
Do not use the instrument in a water vapor atmosphere.
Condensed steam on the sensor will change the heat dissipation rate,
resulting in inaccurate measurements. It may also cause damage to
the sensor.
This instrument is designed to be used in an environment with
a clean air stream without any dust or foreign materials.
Foreign materials may cause damage to the sensor. Also dust or
foreign materials on the sensor will impede accurate measurements.
Do not apply force to the sensor.
If the sensor is deformed, the accuracy of the sensor may be
affected.
When measuring, ensure that the direction mark is facing into
the airflow.
Otherwise, the measurement may be inaccurate, as some sensors
(uni-directional probes) have a specific directivity.
Do not use or leave the instrument in a high temperature,
high humidity or dusty environment. Do not leave this
instrument under direct sunlight for a prolonged period.
The instrument may not function properly out of the specified
operating conditions.
Forbidden
Hot surface
Don’t touch
Explosive
Use properly
Forbidden
Set up properly
Forbidden
Forbidden
Forbidden

iii
Do not subject the instrument or the probe to strong impacts.
Dropping the unit or placing heavy objects on it may cause damage
or malfunction to the instrument.
Never disassemble, modify or repair the product.
Failure to observe the above may cause short circuit and/or other
failure that will affect the performance.
Do not pick up or carry the instrument by the probe cable.
It may cause a malfunction or the wire may break.
Remove the batteries from the battery compartment when
storing the instrument. Do not leave exhausted batteries in the
battery compartment. When inserting batteries be sure to
insert them with the polarity facing the correct direction.
Failure to do so may cause battery leakage.
Do not wipe the instrument with a volatile solvent.
The body may deform or deteriorate. Use a soft dry cloth to remove
stains. If stains persist, soak the cloth in a neutral detergent and
wipe the instrument with the soft cloth. Never use volatile solvents
such as thinner or benzene.
Discharge any built-up static electricity from your body before
touching the instrument.
The built-up static electricity may influence the readings and cause
damage to the circuit.
Regularly check the head of the probe for contamination.
Impurities (such as dust) on the sensor may affect the
accuracy of the measurements.
To get rid of dust, use a blow blush for cameras to blow it off, or you
can rinse it with water and allow it to air-dry completely.
*Be sure to turn the power off before you clean it.
*Never dry the probe with heat. (Heat may cause permanent damage
to the sensor.)
Do not remodel/
disassemble
Electrified
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Use properly
Use properly

iv
Do not move the main unit and the probe from a cold place to
a warm place quickly. It will cause dew condensation.
Even when used in an environment within the specified operating
temperature and humidity, a sudden temperature change may
cause condensation. Condensation generated on the sensor may
cause inaccurate measurements. Condensation on metal parts may
cause rusting and lead to a malfunction.
Do not touch the LCD screen with a sharp-pointed object or
with excessive pressure.
It may cause distortion of the screen or a malfunction. Also a rapid
temperature change may cause a malfunction of the screen.
When storing the instrument, put the instrument in the
carrying case and keep it in a place with an ambient
temperature of -10 to 50°C and no condensation.
Do not dispose of the instrument as a household waste.
Please note that the disposal of the instrument and the batteries
should be in line with your local or national legislation. For details,
please contact your local distributor.
Set up properly
Forbidden
Forbidden
Forbidden

v
Table of Contents
§ 1 Part Names and Functions (Instrument) ....... 6
Part Names and Functions (Main Body)............................... 6
Part Names and Functions (Probe)....................................7
§ 2 Preparation for Measurement........................ 8
Installing Batteries ..........................................................8
Battery Level Indicator .................................................... 9
Changing Units for the Readings.......................................9
§ 3 How to Measure........................................... 10
§ 4 Specifications .............................................. 11
§ 5 Troubleshooting .......................................... 12
§ 6 Compensation of Air Velocity Value ............. 13
§ 7 Warranty and After Service ......................... 14
Kanomax Limited Warranty ............................................. 14
§ 8 Contact Information .................................... 15

6Part Names and Functions (Instrument)
§ 1 Part Names and Functions (Instrument)
Part Names and Functions (Main Body)
＜Side＞＜Front＞＜Back＞
Power/Function Switch is a multifunction switch that can be slid up and
down, and pressed.
1. Pressing will switch the power on and off. Press and hold the switch
for more than 1 second until the LED indicates the change of the
ON/OFF status.
2. Sliding the switch down will change the measurement mode in the
following order: FAST SLOW Air Temperature FAST
3. Sliding the switch up will hold the display. Slide up, down or press
the switch to continue.
3. Pause
ON/OFF
1. Press and hold for more than 1
second.
2. FAST/SLOW/Air Temperature
Battery Case
Power/Function
Switch
Display
*Do not leave the
probe inlet open
except when
replacing probe.
Probe Connector
＜Enlarged view of the Power/Function Switch＞

Part Names and Functions (Instrument) 7
Part Names and Functions (Probe)
To replace the probe, push and hold the
buttons on both sides of the connector and
pull the probe out.
Do not remove or install the probe while
the power is on.
φ約３．３mm
Air Temperature (temperature
compensation) Sensor
Air Velocity Sensor
Directional Point
Sensor
Grip
*Air Velocity/Air Temperature
(temperature compensation)
sensors are built in.
*During measurement, the whole
surface of the sensor should be
exposed to the wind.
*Face it windward

8Preparation for Measurement
§ 2 Preparation for Measurement
Installing Batteries
Use four AA size batteries.
Make sure that the power is off before inserting the batteries.
If you are using charging batteries, charge them with a special
charger prior to use.
＜Back (Battery Case)＞
1. Slide the cover of the battery case down
along the rail.
2. Slide the cover until it stops, and then lift it
up.
3. Insert the batteries in the order shown in
the left figure, observing polarity.
4. Replace the battery cover by following the
reversed procedures 1 and 2.
To put the battery cover back,
do not first engage the detent
at the top end.
Follow the above-mentioned
procedure backwards to slide
the cover back.
If you forcibly try to click the
cover onto the body, it may
be broken.
＋
-
-
-
-
＋
＋
＋
２
１
３
４

Preparation for Measurement 9
Battery Level Indicator
Battery level is displayed as below depending on the charge left:
Guaranteed operating voltage range of the battery is more than
4V.
When battery voltage decreases to less than 4V, the display will
go on and off and the power will be turned off automatically.
When you are using a charging battery, recharge the battery a
little early, before the 4.3V -4.0V mark is displayed.
Changing Units for the Readings
The units can be changed using the
dip switch.
You can find the dip switch in the
battery box.
(Lower than 4.0V)
(More than 4.6V）
Blinking of the indicator
(4.3V –4.0V）
(4.6V - 4.3V）
Sufficient
Replacement of
Batteries
Medium
*SW 2 is not used.
Units
１
SW No.
m/s °C
FPM °F
OFF (factory default)
ON
1 2
ON