Kärcher BRC 30/15 C *JP User manual

Register and win!
www.kaercher.com
BRC 30/15 C
59622110 03/12
Deutsch 3
English 10
Français 17
Italiano 25
Nederlands 33
Español 40
Português 47
Dansk 54
Norsk 61
Svenska 68
Suomi 75
Ελληνικά 82
Türkçe 90
Русский 97
Magyar 105
Čeština 112
Slovenščina 119
Polski 126
Româneşte 133
Slovenčina 140
Hrvatski 147
Srpski 154
Български 161
Eesti 169
Latviešu 176
Lietuviškai 183
Українська 190

English
– 1
Please read and comply with
these original instructions prior
to the initial operation of your appliance and
store them for later use or subsequent own-
ers.
The packaging material can be recy-
cled. Please do not place the pack-
aging into the ordinary refuse for disposal,
but arrange for the proper recycling.
Old appliances contain valuable ma-
terials that can be recycled. Please
arrange for the proper recycling of
old appliances. Please dispose your old ap-
pliances using appropriate collection sys-
tems.
Notes about the ingredients (REACH)
You will find current information about the
ingredients at:
www.kaercher.com/REACH
Before first start-up it is definitely necessary
to read the safety indications Nr. 5.956-
251!
Danger
Immediate danger that can cause severe
injury or even death.
몇Warning
Possible hazardous situation that could
lead to severe injury or even death.
Caution
Possible hazardous situation that could
lead to mild injury to persons or damage to
property.
This appliance is intended for commercial
use as a wet cleaning appliance for carpets
as depicted in these operating instructions
as well as in the descriptions and safety
notes in the enclosed brochure "Safety indi-
cations for brush cleaning appliances and
spray extraction appliances".
The applicance sprays cleaning solution
from the fresh water tank onto the carpet to
be cleaned, works the detergent into the
carpet with a brush roller and vacuums the
dirt and used detergent into the waste wa-
ter reservoir.
If required, an accessorz (such as a hand
nozzle) can be attached..
Contents
Environmental protection . . EN . . .1
Safety instructions . . . . . . . EN . . .1
Proper use . . . . . . . . . . . . . EN . . .1
Function . . . . . . . . . . . . . . . EN . . .1
Control elements . . . . . . . . EN . . .2
Start up. . . . . . . . . . . . . . . . EN . . .2
Operation . . . . . . . . . . . . . . EN . . .3
Shutting down . . . . . . . . . . EN . . .4
Transport . . . . . . . . . . . . . . EN . . .4
Storage. . . . . . . . . . . . . . . . EN . . .4
Maintenance and care . . . . EN . . .4
Troubleshooting . . . . . . . . . EN . . .5
Technical specifications . . . EN . . .6
EC Declaration of Conformity EN . . .7
Spare parts. . . . . . . . . . . . . EN . . .7
Warranty. . . . . . . . . . . . . . . EN . . .7
Environmental protection
Safety instructions
Symbols in the operating instruc-
tions
Proper use
Function
10 EN

– 2
1 Push handle
2 Key detergent solution
3 Dome
4 Dirt water reservoir
5 Dome lock
6 Fresh water tank
7 Vacuum bar
8 Cleaning head
9 Lock of pushing handle
10 Cleaning head screw
11 Detergent hose coupling
12 Drainage hose for fresh water
13 Suction hose
14 Operating field
1 Fuse for brush drive
2 Fuse for suction turbine
3 Power switch
A Normal operation
B OFF - Appliance is switched off.
C Operation with hand nozzle
Swivel the domelock to the front.
Lift up the waste water reservoir and put
it aside.
Fill the fresh water tank with hot water
(max. 60°C, capacity 15 liters).
Pour in detergent.
If you require further information please re-
quest the product information sheet and the
DIN safety data sheet for the respective
cleaning agent.
몇Warning
Health risk, risk of damage. Observe all in-
dications on the detergent used.
For considerate treatment of the environ-
ment use detergent economically.
Insert the waste water container back
onto the appliance.
Replace the lid of the waste water res-
ervoir and align it.
Swivel the dome lock to the rear.
Control elements Operating field
Start up
Carpet cleaning RM 764 liquid
Defoaming RM 761
11EN

– 3
Vacuum loose dirt with a vacuum clean-
er prior to cleaning.
Swivel the pushing handle lock to the
outside, set the desired pushing handle
height and close the lock.
Insert the mains plug into the socket.
Caution
Risk of damage. Check the object to be
cleaned prior to using the appliance in an
inconspicuous place for colour fastness
and water resistance.
Danger
Risk of electric shock.
Do not let the mains cable come in contact
with the rotating brushes or rotating pads.
Set the appliance switch to normal op-
eration - start the suction turbine and
the brush drive.
Use the detergent solution key on the
push bow to spray on detergent solu-
tion.
Run across the surface to be cleaned in
overlapping paths. Pull the appliance
backwards during this procedure (do
not push).
If the waste water reservoir is filled to 3/
4 of its capacity, switch the appliance
switch to "OFF".
Swivel the domelock to the front.
Lift the waste water reservoir off the ap-
pliance and empty it.
몇Warning
Please observe the local provisions regard-
ing the wastewater treatment.
Note
If the waste water reservoir is full, dirty wa-
ter will flow back onto the carpet, as soon
as the appliance is switched off.
Only use accessories and spare parts
which have been approved by the manu-
facturer. The exclusive use of original ac-
cessories and original spare parts ensures
that the appliance can be operated safely
and trouble free.
Connect the provided adapter to the de-
tergent hose of the accessory tools.
Pull the suction hose out of the dome.
Insert the suction hose of the accessory
tool into the dome instead of the suction
hose.
Connect the coupling of the detergent
hose on the appliance to the detergent
hose of the accessory tool.
Set the appliance switch to operation
with manual nozzle - the suction turbine
will start.
Use the lever on the accessory tool to
spray on detergent solution.
Important
When unplugging the accessory tools, the
adapter must be removed from the appli-
ance, so that the water output on the appli-
ance is closed.
Recommendation: Leave the adapter on
the hose of the accessory tool.
Operation
Emptying the Dirt Water Reservoir
Operation with accessory tools
12 EN

– 4
–Highly soiled spots should be
presoaked and the detergent solution
should soak 5 to 10 minutes.
–Always work from the light to the shade
(from the window to the door).
–Always work from the cleaned to the un-
cleaned surface.
–The more sensitive the surface (oriental
rugs, berbers, upholstery material) the
lower the cleaning solution concentra-
tion should be.
–Rugs with jute backing can shrink if too
much water is used and can bleed col-
ours.
–Brush high-fiber rugs in the direction of
the weave after cleaning (using a fiber
brush or a scrubber).
–Do not step on cleaned surfaces until
they have dried and do not place furni-
ture on them to avoid pressure spots or
rust stains.
–When cleaning previously shampooed
carpets, foam will be generated in the
dirt water reservoir. In such a case add
Foam ex RM 761 to the dirt water reser-
voir.
Set the appliance switch to "OFF".
Empty the dirt water reservoir.
Pull the drain hose for the fresh water
off the hose nipple an drain the deter-
gent solution.
Fill the fresh water tank with approx. 2
liters of hot water (max. 60°C) and flush
the spray system by pressing the deter-
gent solution key.
Disconnect the mains plug from the
socket.
Pull the drain hose for the fresh water
off the hose nipple an drain the deter-
gent solution.
Clean the sieves on the fresh water
tank and inside the dome.
Rinse the dirt water tank with clear wa-
ter.
Tilt the appliance backwards and clean
the cleaning head and the vacuum bar..
In case of danger of frost:
Empty the fresh and dirt water reser-
voirs.
Store the appliance in a frost-protected
room.
Caution
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
Use the pushing handle to push the ap-
pliance.
When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
Caution
Risk of injury and damage! Note the weight
of the appliance in case of storage.
This appliance must only be stored in inte-
rior rooms.
Danger
Danger of injury by electric shock.
First pull out the plug from the mains before
carrying out any tasks on the machine.
Check high power cable, extension ca-
bles and hoses for damage every time
before use.
Check spray pattern of the nozzle.
Caution
Risk of damage. Never use a wire or a nee-
dle to clear plugged nozzles, but rinse them
with hot water (see "Troubleshooting").
Cleaning tips
Shutting down
Cleaning the device
Frost protection
Transport
Storage
Maintenance and care
Maintenance intervals
Daily before use
13EN

– 5
Check hoses and seals to see if there
are damages. Have defective parts re-
placed by Customer Service.
Check the brushes for wear, replace if
required.
The brushes are considered worn, if the
bristles have the same length as the
yellow indicator bristles.
Empty the fresh water tank and waste
water reservoir.
Tilt the appliance backward and store it
on the pushing handle.
Unscrew and remove the left and right
screws on the cleaning head.
Remove the cleaning head.
1 Nozzle
2 Fastening clip
3 Hose clip
Pull the fastener clip off to the side.
Pull the nozzle backwards out of the
support plate.
Open the hose clip and pull the nozzle
off the hose.
Insert the new nozzle into the hose.
Assemble it back in the reverse se-
quence.
Note
When inserting the nozzle into the support
plate, watch for the correct alignement of
the nozzle.
Empty the fresh water tank and waste
water reservoir.
Tilt the appliance backward and store it
on the pushing handle.
Unscrew and remove the left and right
screws on the cleaning head.
Remove the cleaning head.
1 Brush roller
2 Brush storage screws
3 Toothed belt cover
4 Motor attachment nuts
Loosen the screw on the toothed belt
cover screw and remove the cover.
Unscrew the nuts on the motor attach-
ment and slide the motor to the brush.
Remove the toothed belt.
Loosen the threaded pin of the toothed
gear pulley on the brush and remove
the toothed gear belt.
Unscrew the screws of the brush bear-
ings and pull the bearings from the
brush shaft.
Lift the drive end of the brush roller out
of the housing and pull the opposite
side out of the bearing.
Install the new brush in reverse order.
Danger
Danger of injury by electric shock.
First pull out the plug from the mains before
carrying out any tasks on the machine.
Every 25 operating hours
Maintenance Works
Replace the nozzle
1
2
3
Exchanging the brush
Troubleshooting
1
22
3
4
14 EN

– 6
Get the electrical components checked and
repaired only by authorised customer serv-
ice persons.
Contact an authorised customer service
person in case of problems not mentioned
in this chapter or if you are in doubt or when
you have been explicitly asked to do so.
Plug in the main plug.
Check facility fuse.
Reset the suction turbine fuse on the
control panel.
Clean the vacuum bar.
Check, clean or replace the seal on the
dome.
Empty the dirt water reservoir.
Insert the suction hose properly on the
dome.
Check the suction hose for damages.
Set the appliance switch to normal op-
eration.
Fill the fresh water tank with hot water
(max. 60°C) and rinse the nozzle. Re-
place the nozzle as applicable (see
"Maintenance task/replace nozzle").
Fill up fresh water reservoir.
Clean the sieve in the fresh water reser-
voir.
Set the appliance switch to normal op-
eration.
Reset the brush drive fuse on the con-
trol panel.
Check the drive belt, replace if required.
Replace the worn nozzle with a new
one (see "Maintenance task/replace
nozzle").
Appliance is not working
Suction turbine does not run
Insufficient vacuum performance
No water exiting from nozzle
Brush does not turn
Carpet gets too wet
Technical specifications
Power
Nominal voltage V/Hz 220...240
/ 1~50
Type of protection IPX4
Average power con-
sumption
W 1300
Suction engine out-
put
W 1130
Brush engine output W 76
Cleaning brushes
Working width mm 260
Brush diameter mm 65
Brush speed 1/min 1650
Detergent pump
pressure
MPa 0,4
Detergent pump flow
rate
I/min 1,4
Max. water tempera-
ture
°C 60
Vacuuming
Cleaning power, air
quantity
l/s 46
Cleaning power, neg-
ative pressure
kPa 30,2
Dimensions and weights
Theoretical surface
cleaning perform-
ance
m²/h 100
Fresh/dirt water res-
ervoir volume
l 15/17
Length mm 920
Width mm 360
Height mm 750
Typical operating
weight
kg 52
Noise emission
Sound pressure level
(EN 60704-1)
dB(A) 77
Machine vibrations
Vibration total value
(ISO 5349)
m/s² 1,7
15EN

– 7
We hereby declare that the machine de-
scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.
The undersigned act on behalf and under
the power of attorney of the company man-
agement.
Authorised Documentation Representative
S. Reiser
Alfred Kärcher GmbH Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Phone: [phone]
Fax: [phone]
Winnenden, 2011/05/01
–Only use accessories and spare parts
which have been approved by the man-
ufacturer. The exclusive use of original
accessories and original spare parts
ensures that the appliance can be oper-
ated safely and trouble free.
–At the end of the operating instructions
you will find a selected list of spare parts
that are often required.
–For additional information about spare
parts, please go to the Service section
at www.kaercher.com.
The warranty terms published by the rele-
vant sales company are applicable in each
country. We will repair potential failures of
your appliance within the warranty period
free of charge, provided that such failure is
caused by faulty material or defects in man-
ufacturing. In the event of a warranty claim
please contact your dealer or the nearest
authorized Customer Service centre.
Please submit the proof of purchase.
EC Declaration of Conformity
Product: Spray extraction device
Type: 1.008-xxx
Relevant EU Directives
2006/42/EC (+2009/127/EC)
2004/108/EC
Applied harmonized standards
EN 55014–1: 2006 + A1: 2009
EN 55014–2: 1997 + A2: 2008
EN 60335–1
EN 60335–2–68
EN 61000–3–2: 2006 + A2: 2009
EN 61000–3–3: 2008
Applied national standards
-
CEO Head of Approbation
Spare parts
Warranty
16 EN