Kaysun KP-35 HN8 User manual

OWNER’S MANUAL
Portable Air Conditioner
KP-35 HN8
Thank you for purchasing our Portable Air Conditioner.
Before using your air conditioner, please read this instruction manual carefully and keep it for
future reference. READ AND SAVE THESE INSTRUCTIONS!

2
Contents
Pre p a r a t i o n ----------------------------------------------------------------------------------------- 3
Safet y Prec a u t i o n s ----------------------------------------------------------------------------- 5
Cau t i o n s----------------------------------------------------------------------------------------------- 6
Installation--------------------------------------------------------------------------------------------- 7
Operation ------------------------------------------------------------------------------------------------ 11
Maintenance--- ----------------------------------------------------------------- --- 17
Faults Diagnosi s -------------------------------------------------------------------------------------- 18
Desi gn and Compliance Notes ------------------------------------------- 19
Soc i able Remark ----------------------------------------------------------------------- 20

Preparation
3
front
control panel
horizontal louver
blade
(swing automatically)
handle
(both sides)
Panel
Caster
upper air filter
(behind the grille)
upper air intake
drain outlet
air outlet
lower air filter
lower air intake
drain outlet
(only for pump
heating mode)
power cord outlet
power cord buckle
power plug socket
bottom tray
drain outlet rear

Preparation
4
NOTE: The unit you purchased may be look like one of the following(s):

5
Safety Precautions
This symbol indicates that ignoring instructions may cause death or serious injury.
WARNING:Toprevent injury tothe user or otherpeopleand property damage,the following instructions
mustbe followed. Incorrect operation due to ignoring of instructions may causedeath,harmor damage.
-Installation must beeper formed according to the installation instructions. Improper installation can cause
water leakage, electrical shock, or fire.
-Use only the included accessories and parts, and specified tools for the installation. Using non-standard
parts can cause water leakage, electrical shock, fire, and injury or property damage.
-Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord is
equipped with a three-prong grounding plug to protect against shock. Voltage information can be found
on the side of the unit, behind the grille.
-Install the uniton a flat, sturdy surface.Failure to do so could result in damage or excessive noise and
vibration.
-Theunitmustbe kept free fromobstructiontoensure proper function and to mitigate safety hazards.
-DO NOT modify the length of the power cord or use an extension cord to power the unit. DO NOT share
a single outlet with other electrical appliances. Improper power supply can cause fire or electrical shock.
-Turn off the product when not in use.
-DO NOT install your air conditioner in a wet room such as a bathroom or laundry room. Too much exposure to
water can cause electrical components to shortcircuit.
-DONOTinstalltheunitina locationthatmaybe exposed to combustiblegas,as this couldcausefire.
-The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to rollover
objects, as these could cause tipping.
-DO NOT operate a unit that it has been dropped or damaged.
-Theappliancewithelectricheatershallhaveatleast1-meter space to the combustible materials.
-Do not touch the unit with wet or damp hands or when barefoot.
-DO NOT allowchildrento playwiththe airconditioner. Childrenmustbesupervisedaroundthe unitalways.
-If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power supply
immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has been damaged,
contactatechnicianor customer service for assistance.

Cautions
6
Cautions
-This appliance can be used by children aged from 8 years and above and person with reduced physical,
sensory or mentalcapabilities or lack ofexperience and knowledgeif they have been given supervisionor
instruction concerning useof the appliance in a safe way and understand the hazards involved.Childrenshall
notplay the appliance.Cleaning and user maintenance shall not be made by childrenwithout supervision. (be
applicable for the European Countries)
-This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities or lack of experience and know ledge,unless they have been given super vision or
instruction concerning useofthe appliance by a person responsiblefor their safety.(be applicable for other
countries exceptthe European Countries)
-Children should be supervised to ensure that they do not play with the appliance.
-If the supply cordis damaged,it must be replacedby themanufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
-Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.
-Do not remove any fixed covers. Never use this appliance if it is not working properly, or if it has been
dropped or damaged.
-Do notrun cord under carpeting.Do notcover cord with throw rugs,runners,or similar coverings. Do not route
cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
-Do not operate unit with a damaged cord, plug, power fuse or circuit breaker. Discard unit or return to an
authorized service facility for examination and/or repair.
-To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
-The appliance shall be installed in accordance with national wiring regulations.
-Contact the authorized service technician for repair or maintenance of this unit.
-Contact the authorized installer for installation of this unit.
-Do not cover or obstruct the inlet or outlet grilles.
-Do not use this product for functions other than those described in this instruction manual.
-Before cleaning, turn off the power and unplug the unit.
-Disconnect the power if strange sounds, smell, or smoke comes from it.

Installation
7
Choosing The Right Location
Your installation location should meet the following requirements:
-Make sure that you install your unit on an even surface to minimize noise and vibration.
-The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit)
must be accessible.
-The unit should be located at least 30cm (12”) from the nearest wall to ensure proper air conditioning.
-DO NOT cover the Intakes, Outlets or Remote Signal Receptor of the unit, as this could cause damage to the
unit.
Note About Fluorinated Gasses
-Fluorinated greenhouse gases are contained in hermetically sealed equipment. For specific information on the
type, the amount and the CO2 equivalent in tones of the fluorinated greenhouse gas (on some models), please
refer to the relevant label on the unit itself.
-Installation, service, maintenance and repair of this unit must be performed by a certified technician.
-Product uninstallation and recycling must be performed by a certified technician.
NOTE:
All the illustrations in the manual are for explanation purpose only. Your machine may be slightly different. The
actual shape shall prevail.
The unit can be controlled by the unit control panel alone or with the remote controller. This manual does not
include Remote Controller Operations, see the
<<Remote Controller Instruction>> packed with the unit for details.

Installation
8
Tools Needed
-Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors; -Saw (optional, to shorten window adaptor for
narrow windows)
Accessories
Your Window Installation Kit fits windows 67.5-123cm
(26.5-48”) and can be shortened for smaller windows.
Window Installation Kit(optional)
Step One: Preparing the Exhaust Hose Assembly Press the exhaust those into the window
slider adaptor (into wall window slider adaptor for wall installation) and unit adaptor, clamp
automatically by elastic buckles of the adaptors.
Exhausthose Exhausthoseassembly
Exhaust hose Exhaust hose assembly
Unit adaptorWindow slideradaptor
Unit adaptor Wall exhaust adaptor A
Type window installation Type wall window installation
StepTwo:Install theExhausthoseassemblyto theunit InsertunitadaptoroftheExhausthoseassembly intothelower groove of
the airoutlet ofthe unit whilethehookof theadaptor isalignedwiththe holeseat ofthe air outletandslidedownthe Exhaust hose assembly
along the arrow direction for installation.
Hook Hole Seat
Lower groove. Make sure the adaptor is inserted into the lower groove of the air outlet.
Step Three: Preparing the Adjustable Window Slider
1. Depending on the size of your window, adjust the size of the window slider.
2. If the length of the window requires two window sliders, use the bolt to fasten the window sliders once they are
adjusted to the proper length.
Bolt
Window slider A. Window slider B
Part
Description
Quantity
Unit Adaptor
1 pc
Exhaust Hose
1 pc
*
Window Slider Adaptor
1 pc
*
WallExhaustAdaptorA(onlyforwallinstallation)
1 pc
*
Wall Exhaust Adaptor B(with cap)(only for wall installation)
1 pc
*
Bolt
1 pc
Window Slider A(with hole),Window Slider B
1 pc
Screwandanchor(onlyforwallinstallation)
4 set
*
Foam Seal A (Adhesive)
2 pc
*
Foam Seal B (Adhesive)
2 pc
*
Foam Seal C (Non-adhesive)
1 pc
*
Security Bracket and 2 Screws
1 set
Drain Hose
1 pc
Drain Hose Adaptor(only for heatpump mode)
1 pc
O
S
N H
/OR
O
F
T
F
C U T
TMI MO DE E
R
ON
T E M P T I FMA
E
N R O F F
S L E E P S WI N G
L E D
Remote Controller and Battery
(For remote control models only)
1 set
Items with
*
are optional. Slight variations in design may occur.

Installation
9
Note:Once theExhaustHoseassemblyandAdjustableWindowSlider are prepared, choose from one of the following three installation methods.
Type 1: Hung Window Installation(optional)
Foam seal B
(Adhesive type-shorter)
Window. Window slider B
Foam seal A sliderA. (If required)
(Adhesive type)
Cut the adhesive foam seal A and B strips to the
proper lengths andattachthem to thewindowsash
and frame as shown.
Insert the window slider assembly into the
window opening.
Foam seal C
(Non-adhesive type) Security Bracket
2 Screws
Cut the non-adhesive foam seal C strip to match the
width of the window. Insert the seal between the glass
and the windowframe topreventair andinsectsfrom
Getting into the room.
If desired, install the security bracket with 2 screws as
shown.
Insert the window slider adaptor into the hole of
the window slider.

Installation
10
Foam seal C
(Non-adhesive type)
Security
Bracket
2 Screws
Cut the non-adhesive foam seal C strip to match the If desired, install the security bracket with 2 screws as shown
windowheight.Insertthe foam seal between the glassandthe
window frame to prevent air andinsectsfromgettinginto
the room.
Insert the window slideradaptor into the holeofthe windowslider.
Type 3: Wall Installation(optional)
-Cut a 125mm (4.9inch) hole into the wallfor the WallExhaust Adaptor B.
-Secure the Wall Exhaust Adaptor B to the wall using the four Anchors and Screws provided in the kit.
-Connect the Exhaust Hose Assembly (with Wall Exhaust Adaptor A) to the Wall Exhaust AdaptorB.
Expansion anchor position
Wall Exhaust Adaptor B
Adaptor cap
max 120cm or 47 inch
min 30cm or 12 inch
Note: Cover the hole using the adaptor cap when not in use.
Note: To ensure proper function, DO NOToverextend or bend thehose.Makesurethatthereisnoobstaclearoundtheair
outletoftheexhausthose(intherangeof500mm)to the exhaust system works properly. All the illustrations in this manual are
for explanation purpose only. Your air conditioner may be slightly different.The actualshapeshallprevail.

Operation
11
NOTE: On
some models
°F is instead of
Swing button
Used to initiate the Auto swing feature. When the
operation is ON, press the SWING button can stop
the louver at the desired angle.
Timer button
Used to initiate the AUTO ON start time and AUTO
OFF stop time program, in conjunction with the + & - buttons. The timer on/off indicator light illuminates under the
timer on/off settings.
Mode button
Selects the appropriate operating mode. Each time
you press the button, a mode is selected in a sequence that goes from AUTO, COOL, DRY, FAN
and HEAT (cooling only models without). The mode indicator light illuminates under the different mode settings.
Up (+) and Down (-) buttons
Used to adjust (increasing/decreasing) temperature settings in 1°C/1°F (or 2°F) increments in
a range of 17°C/62°F to 30°C/86°F (or 88°F) or the TIMER setting in a range of 0~24hrs.
NOTE: The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from
one to the other, press and hold the Up and Down buttons at the same time for 3 seconds.

Operation
12
Fan/Ion button (Ion is optional)
Control the fan speed. Press to select the fan speed
in four steps-LOW, MID, HIGH and AUTO. The fan speed indicator light illuminates under different fan
settings except AUTO speed. When select AUTO fan speed, all the fan indicator lights turn dark.
NOTE: Press this button for 3 seconds to initiate ION feature. The ion generator is energized and will help to
remove pollen and impurities from the air, and trap them in the filter. Press it for 3 seconds again to stop the
ION feature.
Sleep(Eco) button
Used to initiate the SLEEP/ECO operation.
Power button
Power switch on/off.
LED display
Shows the set temperature in °C or °F ("°F"no
display for unit with POWER MANAGEMENT feature) and the Auto-timer settings. While on DRY and FAN
modes, it shows the room temperature. Shows Error codes and protection code:
E1-Room temperature sensor error.
E2-Evaporator temperature sensor error.
E3-Condenser temperature sensor error (on some models).
E4-Display panel communication error.
EC-Refrigerant leakage detection malfunction (on some models).
P1-Bottom tray is full--Connect the drain hose and drain the collected water away. If protection repeats, call
for service.
Note: When one of the above malfunctions occurs, turn off the unit, and check for any obstructions.
Restart the unit, if the malfunction is still present, turn off the unit and unplug the power cord.
Contact the manufacturer or its service agents or a similar qualified person for service.

Operation
13
Operation Instructions
COOL operation
-Press the "MODE" button until the "COOL" indicator light comes on.
-Press the ADJUST buttons "+" or "-" to select your desired room temperature. The temperature can be set within a
range of 17°C~30°C/62°F~88°F(or 86°F).
-Press the "FAN SPEED" button to choose the fan speed.
HEAT operation (cooling only models without)
-Press the "MODE" button until the "HEAT" indicator light comes on.
-Press the ADJUST buttons "+" or " - " to select your desired room temperature. The temperature can be set within a
range of 17°C~30°C/62°F~88°F (or 86°F).
-Press the "FAN SPEED" button to choose the fan speed. For some models, the fan speed can not be adjusted under
HEAT mode.
DRY operation
-Press the "MODE" button until the "DRY" indicator light comes on.
-Under this mode, you cannot select a fan speed or adjust the temperature. The fan motor operates at LOW
Speed.
-Keep windows and doors closed for the best dehumidifying effect.
-Do not put the duct to window.
AUTO operation
-When you set the air conditioner in AUTO mode, it will automatically select cooling, heating (cooling only models
without), or fan only operation depending on what temperature you have selected and the room temperature.
-The air conditioner will control room temperature automatically round the temperature point set by you.
-Under AUTO mode, you can not select the fan speed. NOTE: Under AUTO mode, both the AUTO mode and the
actual operation mode indicator lights illuminate for the
unit with POWER MANAGEMENT feature.
FAN operation
-Press the "MODE" button until the "FAN " indicator light comes on.
-Press the "FAN SPEED" button to choose the fan speed. The temperature can not be adjusted.
-Do not put the duct to window.
TIMER operation
-When the unit is on, press the Timer button will initiate the Auto-off stop program, the TIMER OFF indicator light

14
Operation
illuminates. Press the UP or down button to select the desired time. Press the TIMER button again within 5
seconds, the Auto-on start program is initiated. And the TIMER ON indicator light illuminates. Press the up
or down button to select the desired Auto-on start time.
-When the unit is off, press the Timer button to initiate the Auto-on start program, press it again within five
seconds will initiate the Auto-off stop program.
-Press or hold the UP or DOWN button to change the Auto time by 0.5-hour increments, up to 10 hours, then
at 1 hour increments up to 24 hours. The control will count down the time remaining until start.
-The system will automatically revert to display the previous temperature setting if there is no operation in a 5
seconds period.
-Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop
timer program.
-When the malfunction occurs, the Auto Start/Stop timed program will also be cancelled.
SLEEP/ECO operation
-Press this button, the selected temperature will increase (cooling) or decrease(heating) by 1°C/2°F(or 1°F) 30
minutes. The temperature will then increase (cooling) or decrease (heating) by another 1°C/2°F (or 1°F)
after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the
originally selected temperature. This ends the Sleep/Eco mode and the unit will continue to operate as
originally programmed. NOTE: This feature is unavailable under FAN or DRY mode.
Other features
FOLLOW ME/TEMP SENSING feature(optional) NOTE: This feature can be activated from the remote
control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature
control at its location. To activate the follow Me/Temp Sensing feature, point the remote control towards the
unit and press the Follow Me/Temp Sensing button. The remote display is actual temperature at its location.
The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow
Me/Temp Sensing button again. If the unit does not receive the
Follow Me/Temp Sensing signal during any 7 minutes interval, the unit will exit the Follow Me/Temp Sensing mode.
NOTE: This feature is unavailable under FAN or DRY mode.

15
Operation
AUTO-RESTART (on some models)
If the unit breaks off unexpectedly due to the power cut, it will restart with the previous function setting
automatically when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it can not be restarted operation in the first 3 minutes. This is to protect the unit.
Operation will automatically start after 3 minutes.
AIR FLOW DIRECTION ADJUSTMENT
The louver can be adjusted automatically. Adjust the air flow direction automatically:
-When the Power is ON, the louver opens fully.
-Press the SWING button on the panel or remote controller to initiate the Auto swing feature. The louver will
swing up and down automatically.
-Please do not adjust the louver manually.
POWER MANAGEMENT feature(optional)
When the ambient temperature is lower (Cooling mode) or higher (Heating mode) than the setting
temperature for a period, the unit will be automatically operating power management feature. The
compressor and fan motor stop and the power management indicator light
( ) illuminates.
When the ambient temperature is higher (Cooling mode) or lower (Heating mode) than the setting
temperature, the unit will be automatically quit the power management feature.
The power management indicator light turns dark and the
compressor and (or) fan motor run.
Water drainage
-During dehumidifying modes, remove the upper drain plug fromthebackoftheunit,install the drain connector (5/8"
universal female mender) with 3/4"hose(locallypurchased). For the models withoutdrain connector,justattachthe drain
hose to the hole. Place the open end ofthe hose directly over the
Remove the upper drain plug
Continuous drain hose
√
Duringheatingpumpmode,remove the lower drainplug fromthe back ofthe unit, installthe drain connector (5/8" universalfemale
mender) with 3/4"hose(locally purchased). For the models without drain connector just attach the drain hose to the
hole.Place the openendofthe Hoseadaptordirectly over the drainareainyourbasementfloor. NOTE:Makesure the
hose is securesotherearenoleaks.
Remove the lower drain plug
Continuous drain hose
drain hose adaptor
√

16
Operation
Direct the hose toward the drain, makingsure that there are no kinks that willstopthewaterflowing. Placethe endof thehose
intohedrainand make suretheendofthe hoseisdowntoletthe waterflow smoothly.
(See Figs with
√
. Do never let it up. (See Figs with
X
). When the continuous drain hose is not used, ensure that the
corresponding drain plug and knob are installed firmly to preventleakage.
√ drain hose adaptor
X
drain hose adaptor
-When the water level of the bottom tray reaches apredeterminedlevel,theunitbeeps8
times, the digitaldisplayareashows"P1".Now theairconditioning/dehumidification
processwill immediatelystop.However,the fanmotorwill continueto operate (thisis
normal).Carefully move the unitto a drainlocation,remove the bottomdrainplugandlet
thewaterdrainaway. Reinstallthe bottomdrainplug andrestartthe machine untilthe
"P1"symbol disappears.
If the error repeats, call for service.
NOTE: Be sure to reinstall the bottom drain plug firmly to prevent leakage before using
the unit.

Maintenance
17
WARNING:
-Always unplug the unit before cleaning or servicing.
-DO NOT use flammable liquids or chemicals to clean the unit.
-DO NOT wash the unit under running water. Doing so causes electrical danger.
-DO NOT operate the machine if the power supply was damaged during cleaning. A damaged power cord
must be replaced with a new cord from the manufacturer.
Clean the Air Filter
Upper filter
(take out)
Remove the screw,
then take thelower filter out.
CAUTION
DO NOT operate the unit without filter because
dirt and lint will clog it and reduce
performance.
Remove the air filter
Maintenance Tips
-Be sure to clean the air filter every 2 weeks for optimal performance.
-The water collection tray should be drained immediately after P1 error occurs, and before storage to prevent
mold.
-In households with animals, you will have to periodically wipe down the grill to prevent blocked airflow due
to animal hair.
Clean the Unit
Clean the unit using a damp, lint-free cloth and mild detergent. Dry the unit with a dry lint-free cloth.
Store the unit when not in use
-Drain the unit’s water collection tray according to the instructions in the following section.
-Run the appliance on FAN mode for 12 hours in a warm room to dry it and prevent mold.
-Turn off the appliance and unplug it.
-Clean the air filter according to the instructions in the previous section. Reinstall the clean, dry filter before
storing.
-Remove the batteries from the remote control.
Be sure to store the unit in a cool, dark place. Exposure to direct sunshine or extreme heat can
shorten the lifespan of the unit.

Faults Diagnosis
18
Please check the machine according to the following form before asking for maintenance:
Problem
Possible Cause
Troubleshooting
Unit does not
turn on when
pressing ON/OFF
button
P1 Error Code
The Water Collection Tray is full. Turn off the unit, drain the water
from the Water Collection Tray and restartthe unit.
In COOL mode:roomtemperature is lowerthan
the set temperature
Reset the temperature
Unit does not
cool well
The airfilter is blocked withdustoranimalhair
Turn offthe unitand cleanthe filter according to instructions
Exhaust those is not connected or is
blocked
Turnoffthe unit,disconnectthe hose,checkfor blockage and
reconnect the hose
The unit is low on refrigerant
Callaservicetechniciantoinspecttheunitandtopoffrefrigerant
Temperature setting is too high
Decrease the set temperature
The windows and doors in the room are open
Make sure all windows and doors are closed
The room area is too large
Double-check the cooling area
There are heat sources inside the room
Remove the heat sources if possible
The unit is noisy
and vibrates too
much
The ground is not level
Place the unit on a flat, level surface
The air filter is blocked with dust or animal
hair
Turnoffthe unitandcleanthe filteraccordingtoinstructions
The unit makes a
gurgling sound
Thissound is caused by the flowof refrigerant
inside the unit
This is normal

Design and Compliance Notes
19
Design Notice
To ensure the optimal performance of our products, the design specifications of the unit and remote control are
subject to change without prior notice.
Energy Rating Information
The Energy Rating for this unit is based on an installation using an un-extended exhaust duct without window slider
adaptor or wall exhaust adaptor A (as shown in the Installation section of this manual).
Unit Temperature Range
Exhaust hose installation
The exhaust hose and adaptor must be installed or removed in accordance with the usage mode.
For COOL, HEAT (heat pump type) or AUTO mode must be installed exhaust hose.
For FAN, DEHUMIDIIFY or HEAT (electrical heat type) mode must be removed exhaust hose.
Cool
Dry
Heat (pump heat
mode)
Heat (electrical
heat mode)
17-35°C (62-95°F)
13-35°C (55-95°F)
5-30°C (41-86°F)
≤30°C (86°F)

Sociable Remark
20
When using this dehumidifier in the European countries, the following information must be followed:
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately
for special treatment is necessary.
It is prohibited to dispose of this appliance in domestic household waste. For disposal, there are several
possibilities:
A) The municipality has established collection systems, where electronic waste can be disposed of at least
free of charge to the user.
B) When buying a new product, the retailer will take back the old product at least freeof charge.
C) The manufacture will take back the old appliance for disposal at least free of charge tothe user.
D) As old products contain valuable resources, they can be sold to scrap metaldealers.
Wild disposal of waste in forests and landscapes endangers your health when hazardous substances leak
into the ground-water and find their way into the food chain.