KBC eCopper EECF1-LS1-T-IN-B User manual
eCopper™
QSG-ECEF1-LS1-T-IN-B_Series-Rev1808 www.kbcnetworks.com
Copyright © KBC Networks 2018
Quick Start Guide
EECF1-LS1-T-IN-B
EoC Transmitter with PoC, PoE+ BNC and RJ45 with flying cable
Introduction
The KBC EECF1-LS1-T-IN series is a fully ruggedized Ethernet over coax
transmitter. This transmitter provides connectivity for one 10/100Mbps IEEE
standard twisted pair copper port over a 75ohm coaxial cable. Power is
supplied from one of the headend receivers, EECF16-GN3-R, EECF8-GN3-R,
EECF4-DN1-R, or EECF1-LN1 –R Ethernet over coax switch through the coaxial
cable by Power over Coax (PoC) technology. This transmitter provides
PoE/PoE+ support. Varying data rates are supported depending on cable
distance and quality. The plug-and-play design ensures ease of installation
with no electrical adjustment needed. LED indicators are provided to clearly
show the operational status of the unit.
The size of the transmitter is suited for fitting inside camera housing and
where space is minimal.
Features
•802.3af/802.3at compliant
•PoE+ (30W) and Power over Coax
•Coax data rate >50Mbps (300m) based on coax quality
•PoE+ is supported up to 300m based on coax quality and applied voltage
to headend
•Powered by PoC from headend: EECF16-GN3-R,EECF8-GN3-R,EECF4-DN1-
R,or EECF1-LN1-R
•Complete protection design including surge protection, lighting protection
•Unique PoC transmission protection design together with 1,4,8 and 16
channels
Downloads
Full specifications, features and additional information can be found on the
relevant product page on the KBC website as well as in the downloads section:
http://www.kbcnetworks.com/downloads
Page 2 of 9
General
Check the product upon receipt for any visible damage which may have been
caused during shipping.
Physical Deployment
This equipment must be installed and operated in accordance with
instructions found in this document. Failure to comply with these instructions
will invalidate warranty.
Application
Panel views
12 3
1-Ethernet connecter; 2- LED indicator; 3-Coax cable connecter;
Page 3 of 9
LED
Color
Status
Description
PWR
Green
On
Power supply is normal.
Coax
Link/Act
Green
On
Blink
EoC connection is normal.
Transmission is active.
Ethernet
Link/Act
Green
On/Blink
On: Ethernet link is normal.
Blink: The data is active.
RJ45 Definition
Pin
Signal
1
TD+
2
TD-
3
RD+
4
N/A
5
N/A
6
RD-
7
N/A
8
N/A
Page 4 of 9
Dimensions (Unit = mm)
Equipment:
Installation Accessories
Page 5 of 9
Specifications
Items
Description
Power
Power Input
>40Vdc PoC
Consumption
<2W(No PoE)
Cable
Transmission Medium
75-5 or above coaxial cable
and Cat5e/6 cable
Operating frequency
2M~28M
Modulation
Wavelet-OFDM
Transmission rate
210Mbps (Max.)
Power negotiation cycle
1S
Overcurrent
720mA
Overcurrent protection
time
<2mS
Transmission distance
500m
Ethernet Port
Transmission medium
Cat5e/6
Standard
IEEE802.3，IEEE802.3U
Ethernet delay
<1mS
Protection
ESD
IEC61000-4-2
Anti-thunder protection
IEC61000-4-5 level 3
Operation
Environment
Operating temperature
-20℃~+60℃
Storage temperature
-40℃~+85℃
Humidity (No-
Condensing)
0~90%
Mechanical
Dimension (L×W×H)
76mm*37mm*29mm
Material
Aluminum
Color
Black
Weight
0.25Kg
Page 6 of 9
Installation Instructions
Please check the following items before installation. If any missing, please
contact the dealer.
⚫EoC Transmitter ----------------x1
⚫Wall mounting clamp--------- x1
⚫QSG/User manual-------------- x1
⚫Screw ----------------------------- x2
Please follow the installation steps below:
1) Attach the clamp to the wall using the 3X10mm screws;
2) Press the transmitter into the clamp;
Page 7 of 9
3) Use a network cable to connect the RJ45 port of transmitter and the
Ethernet switch, plug the network cable in the UTP port of transmitter,
and use a grounding wire to connect the grounding terminal;
4) Check if the installation is correct and the device is operating normally.
Trouble Shooting
Please refer to the following information if the device does not work:
⚫Please confirm if the installation is done according to factory installation
requirements;
⚫Please confirm if the RJ45 cable order is in accordance with the
EIA/TIA568A or 568B industry standards;
⚫The maximum transmission distance depends on the signal source and
cable quality. Please do not exceed the maximum transmission distance;
⚫Please replace the failed device with a proper one to check if the device
is damaged; If the problem still exists, please contact the dealer.
Warranty Information
KBC Networks extends the Limited Warranty to the original owner/purchaser
of this product in according to the Warranty Policy posted in KBC Networks’
website at www.kbcnetworks.com.
KBC Networks extends the following Limited Warranty to the original
owner/purchaser of this product: if this product, or any part or portion
thereof, shall prove upon examination by KBC Networks, to be defective in
material or workmanship, KBC Networks will repair or replace such part or
portion at KBC Networks’ option. The warranty period on the repaired or
replaced part or portion of this product shall be limited to the unexpired term
of the original warranty. The buyer shall be responsible for all shipping and
transportation of the product to KBC Networks for any performance under this
warranty.
Conditions and Exceptions:
Page 8 of 9
a) Any accident to this product, any misuse or abuse, alternation, use in
modified form, or any attempt to repair this product shall void this warranty.
These conditions to the warranty include, but are not limited to, incorrect
power connections, physical damage due to mechanical shock, exposure to
moisture, and circuit modification;
b) Should this product prove defective following purchase, the buyer, not the
manufacturer, distributor, or retailer, assumes the entire cost of all servicing
or repair, except as otherwise provided by the terms of this warranty;
c) For breach of any written or implied warranty on this product, the buyer is
limited to the following damages:
i. The cost of labor to repair or replace defective parts or portions of this
product, and
ii. The cost of the repaired or replaced parts or portions of this product;
d) No other expressed or implied warranties have been made or will be made
on behalf of KBC Networks with respect to the sale, repair, installation,
operation, or replacement of this product. KBC Networks disclaims any
implied warranty of merchantability of this product or its fitness for any
purpose, and the buyer agrees that this product is sold “as is” and that the
entire risk of the quality and performance of this product is with the buyer,
except as otherwise provided by the terms of this warranty;
e) Some states/jurisdictions do not allow exclusions or limitations of
incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply to you;
f) If you do not wish to be bound by any of the provisions in this warranty,
please return the product(s) immediately.
This warranty does not apply in Australia.
authorization for out of warranty repairs and any further product information.
Table of contents
Other KBC Transmitter manuals
