KBC eCopper EERF1-LS1-T-IN-B User manual

eCopper™
QSG-EERF1-LS1-T-IN-B_Series-Rev2101 www.kbcnetworks.com
Copyright © KBC Networks 2021
Quick Start Guide
EERF1-LS1-T-IN-B
EoU Transmitter –1 UTP with fly cable and 1 RJ45
Introduction
The KBC EERF1-LS1-T-IN-B is a fully ruggedized Ethernet over UTP transmitter.
This transmitter provides connectivity for one 10/100Mbps IEEE standard
electrical copper port over UTP cable. Power is supplied from one of the
headend receivers, EERF16-GN3-R-RX-B, EERF8-GN3-R-RX-B, EERF4-DN1-R-WN-
B or EERF1-LN1-R-MN-B Ethernet over UTP units through the UTP cable by
Power over Wire (PoW) technology. The transmitter provides PoE+ support.
Varying data rates are supported depending on cable distance and quality. The
plug-and-play design ensures ease of installation with no electrical adjustment
needed. LED indicators are provided to show the operational status of the
unit.
The Ethernet port of the transmitter includes a flying cable. Its size is suited
for fitting inside camera housings and where space is limited.
Features
•802.3af/802.3at compliant
•Power over Wire technology
•UTP data rate >40Mbps (300m)
•Based on cable quality, cable pairs used (1, 2 or 4 pairs) and voltage
applied to cable (48~57VDC) from headend, PoE and PoE+ are supported
by PoW up to 400m
•Powered by PoW from EERF16-GN3-R-RX-B, EERF8-GN3-R-RX-B, EERF4-
DN1-R-WN-B or EERF1-LN1-R-MN-B headend
•Complete protection design including surge and lightning protection
•Unique PoW transmission protection design together with a 1, 4, 8 or 16
channel receiver at headend
Downloads
Full specifications, features and additional information can be found on the
KBC website: www.kbcnetworks.com.

Page 2 of 8
General
Check the product upon receipt for any visible damage which may have been
caused during shipping.
Physical Deployment
This equipment must be installed and operated in accordance with
instructions found in this document. Failure to comply with these instructions
will invalidate the warranty.
Application

Page 3 of 8
Panel views
Top view
Side views
123
4
5
Network cable panel Ethernet panel
1-48VDC power input; 2- LED indicators; 3-Network cable connector;
4-Ethernet connector (flying cable); 5-Grounding terminal.
LED
Color
Status
Description
PWR
Orange
On
Power supply is normal.
PoW
Green
On
PoW power supply is normal.
U-LINK
Green
On
EoU connection is normal.
PoE
Green
On
Successful handshake with PD and supplying
power to PD.
E-L/A
Orange
On/Blink
On: Ethernet link is normal.
Blink: Data is active.

Page 4 of 8
Ethernet RJ45 Definition
Pin
Signal
1
TD+
2
TD-
3
RD+
4
N/A
5
N/A
6
RD-
7
N/A
8
N/A
UTP Port Definition
Pin
Signal
1
PoW+
2
PoW+
3
PoW-
4
PoW+
5
PoW+
6
PoW-
7
PoW-
8
PoW-
Notes:
★Please use straight-through cable rather than cross-over cable.
8 wires transmission: all 8 wires need to be connected.
4 wires transmission: any 2 wires of PIN 1,2,4 and 5 as “+”, any 2 wires of PIN
3,6,7 and 8 as “-”.
2 wires transmission: any 1 wire of PIN 1,2,4 and 5 as “+”, any 1 wire of PIN
3,6,7 and 8 as “-”.

Page 5 of 8
Dimensions (Unit = mm)
Equipment:
29
30
Installation Accessories:

Page 6 of 8
Specifications
Items
Description
Power
Power input
>40Vdc PoW
Consumption
<2W (Non-PoE)
Cable
Transmission Medium
Cat5e/6 cable
Operating frequency
2M~28M
Modulation
Wavelet-OFDM
Transmission rate
210Mbps (Max.)
Power negotiation cycle
1S
Overcurrent
720mA
Overcurrent protection time
<2mS
Transmission distance
*400m
Ethernet Port
Transmission medium
Cat5e/6
Standard
IEEE802.3，IEEE802.3U
Ethernet delay
<1mS
Protection
ESD
IEC61000-4-2
Anti-thunder protection
IEC61000-4-5 level 3
Operation
Environment
Operating temperature
-20℃~+70℃
Storage temperature
-40℃~+85℃
Humidity (Non-Condensing)
0~90%
Mechanical
Dimension (L×W×H)
76mm*37mm*29mm
Material
Aluminum
Color
Black
Weight
0.2Kg
*Transmission distance depends on signal source and cable quality.

Page 7 of 8
Installation Instructions
Please check the following items before installation. If any are missing, please
contact the dealer.
⚫EoU Transmitter-----------------------x1
⚫Wall clamp with screws --------------x1
Or Velcro strip-------------------------x1
⚫QSG/User manual ---------------------x1
Please follow the installation steps below:
1) Attach the clamp to the wall using the 3X10mm screws.
2) Press the receiver into the clamp.

Page 8 of 8
3) Plug the flying cable into the powered device. Plug the network cable into
the UTP port of the transmitter and use a grounding wire to connect the
grounding terminal.
4) Check that the installation is correct and power on the device to be sure
it is operating normally.
Please follow the installation steps below for product with Velcro strip:
1) Clean and dry surface before application;
2) Peel the loop side of the strip off the product;
3) Peel the sticker off the loop side, and stick it on the surface;
4) Bond the hook side on the product to the loop side and press firmly into
place.
Troubleshooting
Please refer to the following information if the device does not work:
⚫Confirm the installation is done according to factory installation
requirements.
⚫Confirm if the RJ45 cable order is following the EIA/TIA568A or 568B
industry standards.
⚫The maximum transmission distance depends on the signal source and
cable quality. Please do not exceed the maximum transmission distance.
⚫Please replace the failed device with a known working unit to determine
if you have a damaged or faulty unit.
⚫If the problem persists, please contact your nearest KBC office or dealer.
Need Help?
Please visit our website www.kbcnetworks.com or contact your nearest KBC
office or dealer.