KBL Tower space 2000 User manual

TANNING DEVICETANNING DEVICE
ASSEMBLY INSTRUCTIONS & MENU SETTINGS

Copyright and Trademark
© Copyright 2018 KBL GmbH
This documentation only covers products manufactured by KBL GmbH. It must not be duplicated, photocopied,
translated or stored without prior special consent by KBL GmbH. Duplication on electronic media or in a machine
readable form, either in whole or in part, is also prohibited.
is a registered trademark of KBL GmbH.
DISCLAIMER
All information given in this document correspond to the status quo at the date of publication but may be subject
to changes. Therefore, we do not accept any liability for, nor do we guarantee the accuracy and/or completeness
of the information.
EXPORT
Technical equipment and versions of the devices are in accordance with the legal prescriptions of the respective
country of destination. Export to the European Union of the KBL products, listed in this guide, or operation of
the systems in these countries, are not permitted. KBL does not accept any manufacturers liability in case this
direction is not adhered to. It is expressly pointed out that any violation of the export/operation prohibition will
involve substantial risks of liability for the exporter and/or operator.
MANUFACTURER
KBL GmbH
Ringstraße 24-26 · 56307 Dernbach · Germany
DISTRIBUTED BY (CONTACT)
Specified in operating instructions
ORIGINAL ASSEMBLY INSTRUCTIONS
Version: MA_space2000_US_J
Date: June 2018
Item no: 0100036002
Tanning device name [tech.]: T3/50 - 180 u

Assembly Instructions |KBL Tower space 2000
4
Contents
1. General information .......................................... 5
1.1 About these instructions ............................... 5
1.2 Safety signs................................................... 5
1.3 Signal words.................................................. 5
1.4 Transport ....................................................... 6
2. Safety notes ....................................................... 7
2.1 General safety notes ..................................... 7
3. Installation site and dimensions ...................... 8
3.1 Dimensions ................................................... 8
3.2 Distances....................................................... 9
4. Assembly.......................................................... 10
4.1 Tools and aids ............................................. 10
4.2 Option: Alteration exhaust air outlet............ 10
4.3 Option: Alteration for central exhaust air ... 10
4.4 Assembling the tanning device ................... 10
5. Connections & Initial operation...................... 26
5.1 Class I ME equipment ................................. 26
5.2 Overview supply connections ..................... 26
5.3 Connecting the mains voltage..................... 26
5.4 Connecting an external audio source ......... 27
5.5 Level adjustment studio music................... 27
5.6 Operation using different audio sources ..... 27
5.7 Bluetooth connection.................................. 28
5.8 Connecting the channel selection............... 29
5.9 Connecting the external timer..................... 29
5.10 aquaCool-box connections....................... 30
5.11 Connections aquaCool box /tower ........... 30
5.12 Initial operation.......................................... 30
6. Service menu ...........................................................31
6.1 Layout of the interior control panel
numbers ...................................................... 31
6.2 Invoking the service menu .......................... 31
6.3 Service menu - Basics ................................ 32
6.4 Service menu - Overview ............................ 34
6.5 Service codes.............................................. 35
6.6 Service menu - options ............................... 35

Assembly Instructions |KBL Tower space 2000 5
1. General information
1.1 About these instructions
This manual is intended for use by
• qualified, trained and authorized service techni-
cians.
Any person handling, mounting or servicing this tan-
ning device must have read and understood these
instruction.
Keep this manual ready to hand at all times.
1.2 Safety signs
This symbol indicates that general haz-
ards exist for the human health.
This symbol indicates that due to elec-
trical tensions hazards exist to the
human health.
This symbol indicates that due to fall-
ing loads hazards exist to the human
health.
This symbol indicates the danger of
pinching.
When assembling heavy components,
you can pinch your fingers or hands.
This symbol indicates the danger of
burns from hot lamps and housing
parts.
If the tanning device was operated
before being opened, lamps and hous-
ing parts may be hot.
This symbol indicates that damages
may occur at the tanning device, at the
material or at the environment.
Danger due to leakages.
The tanning device can be damaged by
leaking connections.
• Slide the plastic tube up to the stop into the
quick connector socket.
1.2.1 IMPORTANT INFORMATION
This symbol does not identify safety
notices, but states information for a bet-
ter understanding.
1.3 Signal words
DANGER
• Death or serious injury is imminent.
WARNING
• Death or serious injury is possible.
CAUTION
• Moderate or minor injury is possible.

Assembly Instructions |KBL Tower space 2000
6
1.4 Transport
WARNING
Overturning load
Danger of being crushed by heavy parts
of the equipment.
• Keep the safety distance to the trans-
port machine.
• Do not walk under the load.
• Wear safety shoes.
1.4.1 TRANSPORT BY FORKLIFT TRUCK
During transport the tanning device may
be damaged when using forklift forks that
are too short.
• Use only sufficiently long forks.
The box with the tanning device components is
mounted on a pallet.
• Insert the forks carefully into the openings of the
pallet.
• Lift the load by a few centimeters.
• Transport the load carefully to the place of
installation.
1.4.2 OTHER MODES OF TRANSPORT
If a forklift truck cannot be used for transport, the
box must be unpacked and the parts inside must be
transported individually to the place of installation,
e.g. using a dolly. Depending on the weight of the
components, lifting them might require several
people.

Assembly Instructions |KBL Tower space 2000 7
2. Safety notes
2.1 General safety notes
• Follow all instructions given in this manual and all
other documents enclosed with the tanning device.
In addition, observe all relevant statutory provi-
sions and regulations, also those applicable in the
country of operation.
• The tanning device must only be installed and
assembled by qualified, trained and authorized
service technician.
• Arbitrary modifications or conversions of the tan-
ning device are not permissible.
• Observe all danger signs and safety notices
attached to the tanning device.
• Safety notices must not be removed, and safety
equipment must not be disabled or removed.
• The tanning device must only be operated when in
perfect working condition.
• Never operate the tanning device with the outer
covers or acrylic panes removed.
• This tanning device must be operated with an
external timer that is listed in compliance with UL
917.
• Before carrying out any work, the tanning device
must be disconnected from the mains voltage.
DANGER
Live parts
Danger of life or fatal injury due to electric
shock when touching live parts.
• Switch neutral
• Secure against reconnection
• Check for neutrality
• Ground and short-circuit
• Cover or shield any adjacent live parts or
components
CAUTION
Hot surfaces
Danger of burns from hot lamps and
housing parts. If the tanning device was
operated before being opened, lamps
and housing parts may be hot.
• Wait until the tanning device has
cooled down.

Assembly Instructions |KBL Tower space 2000
8
3. Installation site and dimensions
In dry rooms (booths) with sufficient airing.
• Even floor with sufficient load capacity
• Relative humidity: ≤ 70 %
• Room temperature ≤ 30 0C (86 0F)
• Minimal room height 2270 mm (≈89,37 inches)
• Only on a non-combustible basement
3.1 Dimensions
85.83 in
55.12 in
55.31 in
77.28 in

Assembly Instructions |KBL Tower space 2000 9
3.2 Distances
20 in
20 in
20 in
110 in
3,54 in
2,83 in
89.37 in
20 in

Assembly Instructions |KBL Tower space 2000
10
4.1 Tools and aids
• Assembly of the tanning device has to be done
with two persons.
• Combination spanner: SW 13, 17
• Suction cup
• Phillips screwdriver
• Set of Allen keys
• Set of socket spanners
• Potentially ladder
4.2 Option: Alteration exhaust
air outlet
Factory-made, the exhaust air outlet is on the upper
side. If the exhaust air is to be let out on the lower
side, the exhaust air grid has to be exchanged with
the exhaust air cover and the fan accordingly.
4.3 Option: Alteration for
central exhaust air
If the tanning device has to be connected to the
central exhaust air, the exhaust air grid has to be
exchanged with the exhaust air socket.
4.4 Assembling the tanning
device
The line of sight used in the text is from the door side
to the back side.
• Lay down the baseplate and the associated pad
for its entrance area. The baseplate has pits
for the feet of the back plane and side plates.
4. Assembly