Kenmore 758.15408010 User manual

1
Use & Care Guide
Manual de Uso y Cuidado
English / Español
Model 758.15408010
Kenmore ®
Humidifier
P/ 1B72044 05/10
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A .
www.kenmore.com
www.sears.com
Whole House
Humidifier
8 Gallon Output with Digital Readout

2
Safety Signal Words
DANGER: means if the safety information is
not followed someone will be seriously
injured or killed.
WARNING: means if the safety information
is not followed someone could be seriously
injured or killed.
CAUTION: means if the safety information is
not followed someone may be injured.
1. To reduce the risk of fire or shock
hazard, plug humidifier directly into a
120V, A.C. electrical outlet. Do not use
extension cords.
2. Keep the electric cord out of traffic areas.
To reduce the risk of fire hazard, never
put the electric cord under rugs, near heat
registers, radiators, stoves or heaters.
3. Always unplug the humidifier before
moving it, before cleaning, or whenever
the humidifier is not in service.
4. Keep the humidifier clean.
5. Do not put foreign objects inside the
humidifier.
Warranty Information.................................2
General Safety Instructions .............. .......2
To Save A Service Call...................... .......3
Know Your Humidifier........................ .......3
How Your Humidifier Works.......................4
Step 1. Getting Your Humidifier
Up and Running ...................................4
Step 2. Location Instructions ....................5
6. Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
7. Never use your humidifier while any part
is missing or damaged in any manner.
8. To reduce the risk of electrical hazard or
damage to humidifier, do not tilt, jolt or tip
humidifier while unit is running.
9. To reduce the risk of damage to
humidifier, unplug when not in use.
10. To reduce the risk of accidental electrical
shock, do not touch the cord or controls
with wet hands.
11. Note the warning label shown below.
Electrical Hook-Up ..............................5
Step 3. Water Fill .................................6
Step 4. Operating the Controls .........7-8
Using Your Humidifier .......................8-9
Replacement and Care of Filters........10
Cleaning and Maintenance.................11
Troubleshooting ............................12-13
Repair Parts..................................14-15
ONE YEAR FULL WARRANTY ON KENMORE HUMIDIFIER
If any part of this humidifier fails due to a defect in material or workmanship within
one year from the date of purchase, or if the humidifier motor fails due to a defect in
material or workmanship during the second year from the date of purchase,
RETURN THE HUMIDIFIER TO THE NEAREST SEARS PARTS & REPAIR CENTER,
and it will be repaired free of charge. This warranty does not include humidifier
filters, which are expendable parts that can wear out from normal use in less than
one year. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
GENERAL SAFETY INSTRUCTIONS
WARNING:
To reduce risk of fire, electric
shock, or injury always unplug before
servicing or cleaning.
Table of Contents
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬

3
Check the following if your humidifier is not operating.
1. Is power cord attached to outlet?
2. Is there electrical power to outlet?
3. Is fan control on?
4. Is humidity control set high enough?
5. Is the cabinet sitting on a level surface?
Know Your Humidifier ▬▬▬▬▬▬▬▬▬▬
Quiet Comfort
Base
Bottle
Speed &
Humidity
Controls
Bottle Handle
Fan Assembly
Filter:
Replacement No.
32-15508
Housing
Assembly
Humidistat
(On Power
Cord)
Description 758.15408010
* Gallon Output/24 hrs.
Capacity of Bottle
Capacity of Base
* Sq. Ft. Coverage
Fan Speeds
Auto Fan Speed
Replacement Filter
Auto Humidistat
Auto Shut Off
Controls
Rubber Feet
ETL Listed
Volts
Hertz
Amps (High Speed)
Watts (High Speed)
8
1.2 Gallons
1.2 Gallons
1700
3
Yes
32-15508
Yes
Yes
Electronic (Push Button)
6
Yes
120 A.C.
60
1.2
80
To Save A Service Call ▬▬▬▬▬▬▬▬▬▬▬
* Based on an area with average insulation and an 8 foot ceiling height.

4
How Your Humidifier Works ▬▬▬▬▬▬▬
Your new Kenmore humidifier is designed
to satisfy home humidity requirements
through the principle of evaporation of
water in the air. Once the filter becomes
saturated, air is drawn in, passes through
the filter and moisture is absorbed into the
air. All evaporation occurs in the
humidifier so any residue remains in the
filter. This natural process of evaporation
virtually eliminates white dust.
CAUTION: To reduce the risk of
injury, fire or damage to humidifier,
use only cleaners specifically
recommended for humidifiers.
Never use flammable, combustible
or poisonous materials to clean your
humidifier. To reduce the risk of
scalds and damage to humidifier,
never put hot water in humidifier.
Once removed from its carton, remove all
packing materials. Verify the filter is
properly seated (See pg.10).
Dry air
enters
through
the
louvers
in the
housing
Humidified air is
then released
through the top
QuietComfort
Step 1. Getting Your Humidifier Up and Running ▬▬▬▬

5
Selecting A Location
Place humidifier on a flat level surface, take
extra care in leveling when placing the unit
on carpet. Position the humidifier where the
most humidity is needed or where the most
air will be circulated throughout the house
such as near a cold air return.
Moist air (humidity) produced will disperse
into the whole house, but the area closest
to the unit will have the highest humidity.
If the unit is positioned close to a window,
condensation may form on the window
pane. If this occurs the unit should be
repositioned in another location.
NOTE: Due to release of cool, moist air
from humidifier, it is best to direct air away
from thermostat and hot air registers and to
position humidifier next to an inside wall.
Unit should not be placed where cold air
from outside walls or warm air from a hot air
register blows directly on it.
Locate nearest 120V A.C. wall socket in
the location desired, preferably on inside
wall. With the humidifier in the desired
location, route the electrical cord safely so
no one will trip or upset the humidifier.
Plug in the electrical cord.
To reduce the risk of electrical shock, this
humidifier has a polarized plug (one blade is
wider than the other). This plug will fit in a
polarized outlet only one way.
Positioning The Unit
The humidifier should be positioned with the
back (cord exit side) and left side, at least 2
inches away from the wall. Air needs to
enter through all of the louvers in the
housing assembly in order for the
humidifier to operate at peak efficiency.
NOTE: Be sure humidistat (located
approximately 2 inches outside humidifier
body on power cord) is free from
obstruction and away from any hot air
source.
If the plug does not fit fully in the outlet,
reverse plug. If it still does not fit, contact
a qualified electrician to install the proper
outlet. Do not change the plug in any way.
Step 2. Location and Electrical Hook-Up ▬▬▬▬
WARNING:
For your own safety, do not
use humidifier if any parts are damaged
or missing.
Electrical Hook-Up ▬▬▬▬▬▬▬▬▬▬▬▬
WARNING:
To reduce the risk of fire
or shock hazard, humidifier should be
plugged into a 120V A.C. outlet. Do
not use extension cords.
QuietComfort
At least
2” from
wall

6
After the humidifier is positioned where it
will be operating you are ready to fill the
humidifier. The bottle lifts straight up and
away from the base. Take care not to
bump or damage fill valve assembly on
the bottom of the bottle.
Invert the bottle. Press the valve stem
button into the bottle and turn clockwise to
lock in open position. Place bottle under
the faucet. Fill the bottle, being careful not
to allow any debris to get in the bottle.
Debris may interfere with the valve
seating. Once the bottle is full, press the
valve stem button and turn counter
clockwise to release and close.
Place the water bottle back into the humidifier
base. When positioned properly, the plunger
will open and the water will flow into the base.
The base will hold the entire contents of the
water bottle. Once the bottle is empty,
remove it and repeat the filling process. The
humidifier is now filled to capacity. To benefit
from less frequent filling, let the humidifier
exhaust both the water from the bottle and
the base before filling.
Quiet Comfort
Spring Valve
Assembly
PUSH IN TURN
CLOCKWISE
Bottle
Base
Step 3. Water Fill ▬▬▬▬▬▬▬▬▬▬▬▬▬
WARNING:
To reduce the risk of fire or
shock hazard, do not pour or spill water into
control or motor area. If controls get wet, let
them dry completely and have unit checked
by authorized service personnel before
plugging in.
CAUTION:
Use only 32-14900 EPA
Registered Bacteriostat available
from Sears Retail store. Under no
circumstances should you use water
treatment products designed for Roto
belt or Ultrasonic humidifiers.

7
Where you set your desired humidity level
depends on your personal comfort level,
outside temperature and inside temperature.
A starting set point of 30% - 40% ROOM
humidity is recommended but there may be
conditions that require a different setting.
To Operate the Controls
Digital Display
Press the power button once to turn the unit
on* Initially there is a slight delay while
the electronics calibrate.
Two bars (- -) appear during this time. Once
calibration is complete a ROOM humidity
reading between 25% - 95% will be
displayed. A flashing 20 display indicates
that the room humidity is less than 20%
.NOTE: The default settings at initial
startup are (LOW) F1 fan speed and 65%
SET humidity. After desired settings are
selected by the user, they remain as long as
the unit remains plugged in and there is no
power interruption. If the unit is unplugged
the original default settings are employed.
* Humidifier fan should operate at initial start up. If
it does not, refer to “Fan not operating (digital
display is illuminated)” in the “Trouble Shooting”
section on page 12 of this manual.
When Outdoor
Temperature is:
Recommended
Indoor Relative
Humidity (RH)
is:
-10°F
2°F
10°F
20°F*
-24°C
-18°C
-12°C
-6°C*
20%
25%
30%
35%
* and above
Function
Buttons
Digital Display
®
Quiet Comfort
Step 4. Operating the Controls ▬▬▬▬▬▬▬▬▬▬
IMPORTANT:
Water damage
may result if condensation starts
to form on windows or walls.
Humidity SET point should be
lowered until condensation no
longer forms. We recommend
room humidity levels do not
exceed 50%.

8
Speed Button
This humidifier is equipped with a 3-speed
fan control. Initially depressing the speed
button will display the current speed setting.
Each push of the speed button advances the
mode through the settings of (HIGH) F3,
(MEDIUM) F2, (LOW) F1 and (AUTO) A.
The selected setting is displayed on the
digital readout. The higher the setting, the
faster water is evaporated and released into
the air. F1 (LOW) is the quietest setting and
is provided for conditions that do not require
a rapid evaporation rate. When (AUTO) A is
selected the humidifier will determine the
required fan speed needed to bring the actual
room humidity up to the set humidity.
Speed Button
®
Quiet Comfort
Refill Display
For maximum run time both the bottle and the
base should be filled. When both the bottle
and the base empties, the display alternates
the room humidity reading and “F” (FILL),
informing additional water is required. Also at
this time the unit will automatically switch into
DRY OUT MODE and continue to run on the
lowest speed until the filter is dry.
Humidity Control
This button allows you to adjust the
humidity to suit your needs. This
humidifier will automatically cycle on and
off as required to maintain the selected
setting. The readout displays both actual
(ROOM) and desired (SET) humidity
percentage (%) settings when humidity
control button is pressed. The ROOM
readout has a range of 20% to 95%. If the
room humidity level is equal to or less
than 20% the display will show a flashing
20.
The SET readout has a range of 25% to
65% and is adjusted in increments of 5%.
Initially depressing the humidity button will
display the current humidity setting. Each
additional press of the button increases
the setting by 5%. A SET point of 65%
operates the humidifier continuously
regardless of the ROOM reading. The
humidistat that senses the readings is
located on the power cord. Ensure that
this humidistat is free from obstruction.
Humidity Button
®
Quiet Comfort
®
Quiet Comfort
Refill / Dryout Mode
Display
Operating the Controls (cont’d.) ▬▬▬▬▬▬▬▬
Using Your Humidifier ▬▬▬▬▬▬▬▬▬▬▬▬▬

9
NOTE: During this time the room humidity
level will continue to be monitored and the
humidifier will cycle the fan on and off until
the filter is completely dry. The fan will
shut off leaving you with a dry humidifier
that is less prone to mold and mildew
growth. If DRY OUT MODE is not desired,
refill the humidifier with water and the fan
will return to the set speed.
NOTE: Fan automatically switches to
lowest speed during DRY OUT MODE.
Check Filter Indicator
The ability of any humidifier to efficiently
supply humidity output relies heavily on
the condition of the filter. As the filter
loads with impurities it gradually loses its
wicking capability. When this happens,
moisture output is reduced and the
humidifier has to work longer to satisfy the
selected setting. This humidifier has a
check filter reminder timed to appear after
720 hours of operation. When the display
shows an alternating “CF” and “room
humidity” setting at 5 second intervals it is
a reminder to check the filter condition.
NOTE: Some areas have high water
mineral content causing the need for more
frequent filter changes.
Refer to “Replacement and Care of Filter”
on page 10. If a build-up of deposits or
severe discoloration is evident replace the
filter to restore maximum efficiency.
®
Check Filter
Display
Quiet Comfort
Humidistat
The humidistat located on the power cord
senses the percentage of humidity in the
air. It causes the humidifier to cycle on
and off to maintain the selected humidity
SET point. The fan will turn on if the
“ROOM” reading falls 3% below the SET
point and will continue to run the
humidifier until a reading of 1% above the
SET point is achieved. The fan will turn off
until the ROOM reading falls 3% below
the SET point again.
Control Lock Out
To avoid unwanted tampering with the
humidifier settings the controls can be
locked.
Activation Procedure
After the humidifier functions have been
set up, hold the power button down for 5
seconds. The display will show “CL” for 2
seconds; release the power button and
the control will resume the display of the
room humidity. The room humidifier will
continue to function with the locked in
settings. If buttons are operated while
“CL” is active, the “CL” is displayed and
settings are unaffected.
Deactivation Procedure
To deactivate the “CL” function simply
press and hold the power button for 5
seconds. “CL” will flash at the rate of 1
second on and 1 second off for a period of
2 seconds and then resume the display of
room humidity.
QuietComfort
NOTE: Be sure humidistat is located
approximately 2 inches outside humidifier
body and power cord is free from
obstruction and away from any hot air
register.

10
Replace the evaporative wicking filter at least
once per humidification season or more
depending on water conditions in your area.
Filter Replacement
1. Unplug humidifier. Before removing
the filter, we recommend moving the
humidifier to an area where floor
coverings are not susceptible to water
damage. (i.e. kitchen or bath areas.)
2. Remove the water bottle and set aside.
Be sure not to bump or damage the fill
valve.
3. Grasp the housing assembly and lift
straight up and away from the base and
set aside. The filter is now accessible.
4. Take note of the filter position. Remove
the filter. You may want to clean the base
at this time. See the "Cleaning Your
Humidifier" section of this manual.
5. Install a new filter (32-15508) into the
base. Coil the filter and position it
between the uprights in the bottom of the
base. The start and finish of the coil
should be captured at the center of the
base (see diagram) and the filter should
be resting on the floor of the base.
6. Return the housing assembly to the top of
the base. Reposition the humidifier to its
operating position.
7. The humidifier is now ready to be filled for
operation.
QuietComfort
Replacement and Care of Filter ▬▬▬▬▬▬▬▬
WARNING:
To reduce the risk of shock
or injury from moving parts, always unplug
humidifier before removing or replacing
any parts.
CAUTION:
To help retard bacteria growth
and keep maximum efficiency, the filter
should be replaced at least once per
season, or more often under hard water
conditions. Use Kenmore 32-15508
recommended
replacement filter.
QuietComfort

11
Step 1
To make cleaning easier, the humidifier
base should be empty and completely
dried out. To accomplish this, use the
following method:
a. Allow the humidifier to run until the
REFILL message “F” illuminates and
the automatic shutoff has stopped
the humidifier fan.
b. Unplug humidifier.
Step 2
To Remove Parts
See “Replacement and Care of Filter” page 10.
NOTE: There may be a little water still in the
base. Carefully dump the water out or remove
with a sponge.
NOTE: Remove excess
water before cleaning
Step 3
Bi-Weekly Maintenance
Removing Scale
1. Fill the humidifier base with one 8 oz.
cup of undiluted white vinegar. Let
solution stay 20 minutes.
2. Clean all interior surfaces with a soft
brush. Dampen a soft cloth with
undiluted white vinegar and wipe out
the base to remove scale.
3. Rinse thoroughly with clean warm
water to remove scale and cleaning
solution.
Disinfecting Base
1. Pour 1/2 gallon of water and 1/2
teaspoon chlorine bleach into the
base. Let solution stay for 20
minutes, carefully swishing every
few minutes. Wet all surfaces
normally exposed to water.
2. Empty base after 20 minutes. Rinse
with water until bleach smell is gone.
Allow unit to dry out completely.
NOTE: The water bottle should be
cleaned in the same manner as the base.
Rinse thoroughly with clean water after all
steps are complete.
End of Season Maintenance
1. Follow “Bi-Weekly Maintenance”
instructions at end of humidification
season.
2. Remove filter.
3. Let humidifier dry completely before
storing.
4. Store in cool, dry location.
5. Install a new filter in clean humidifier
before next season begins.
NOTE: “Bi-Weekly Maintenance”
procedure is also recommended if
you do not plan to run the humidifier
for one week or more.
Cleaning and Maintenance ▬▬▬▬▬▬▬▬▬▬
WARNING:
To reduce the risk of injury,
fire or damage to humidifier, use only
cleaners specifically recommended for
humidifiers. Never use flammable,
combustible or poisonous materials to
clean your humidifier. To reduce the risk of
scalds and damage to humidifier, never
put hot water in humidifier.
CAUTION:
Local water purity varies from
area to area and under certain conditions
water impurities and airborne bacteria may
promote the growth of microorganisms in
the reservoir of the humidifier. To retard
bacteria growth that may cause odors and
be harmful to your health, use only
Kenmore replacement filters. We also
recommend using EPA approved
bacteriostat, and humidifier cleaner,
available at your local
Sears store.
WARNING:
To reduce the risk of shock,
always unplug humidifier before cleaning
or servicing. If humidifier is not unplugged,
fan could start after housing is removed.

12
TROUBLE PROBABLE CAUSE REMEDY
Digital display not
illuminated.
• No Power.
• Power button has not been
depressed.
• Check 120 volt power source.
• Press power button once to turn
on.
Fan not operating (Digital
display is illuminated).
• ROOM humidity level
is not 3% or more
• Reservoir is empty.
• Raise SET humidity level if
desired.
• Increase fan speed.
• Fill humidifier with water.
Fan running continuously.
• SET humidity level is
65%.
• ROOM humidity level has not
reached 1% or more above
SET humidity level.
• A SET humidity percentage of
65% operates fan continuously.
Adjust SET level between 25% -
60%.
• Continue to run until desired
humidity level is achieved. This
may take up to 48 hours initially.
Poor evaporation of water.
• CHECK FILTER message
flashing.
• Mineral buildup on filter.
• Change to a fresh new filter.
• NOTE: Local water purity varies
from area to area.
Bottle empties completely.
• This is normal for initial
filling.
.• Refill bottle for maximum run
time.
Bottle continues to empty
after complete filling. • Air is entering water bottle. • Check for leak in water bottle.
Bottle not emptying.
• Spring Valve Assembly
damaged or missing post in
bottom of base.
• Base full of water.
• Check orientation of bottle.
Reposition so that fill valve on
bottom of bottle is depressed by
post in bottom of base.
• The base will hold the contents
of water bottle (1.2 gallons).
Continue to run humidifier to
deplete water from base.
Display blinks or fan moves
slightly when humidifier is
plugged in.
• Normal. • No action required.
Fan operating slower than
speed registered on digital
display.
• Humidifier in “DRY OUT
MODE”.
• Humidifier automatically
switches fan to (LOW) F1 when
“F” and alternating room
humidity is displayed.
Humidifier not shutting off
during “DRY OUT MODE”. • Filter not dry.
• During DRY OUT mode the
humidifier will continue to run on
LOW speed as required for up to
2 hours or until the filter is
completely dry.
Alternating “F” and room
humidity displayed. • Reservoir is empty. • Fill humidifier with water.
Alternating “CF” and room
humidity displayed. • Filter may be dirty.
• Replace filter.
• Unplug unit for 30 seconds and
replug into clear display.
Troubleshooting ▬▬▬▬▬▬▬▬▬▬▬▬▬▬

13
2
3
4
6
5
7
8
1
Parts List for Kenmore Humidifier
Model No. 75
8.154
080
10
Repair Parts
▬▬▬▬▬▬▬▬▬▬▬▬▬▬

14
Parts List for Kenmore Humidifier
Model No. 758.15408010
Always order by part number - Not by key number
Key No. Part No. Description
1 758.15408010 Housing, Upper Assembly
(includes all parts 1-9)
2 32-15508 † Filter
3 831188-1 Support, Float
4 831189 Float, Reservoir
5 831187-1 Base
6 831190 Foot Rubber
7 831199 Bottle Assembly
8 831207 Cap, Screw
9 1B72044 Owner’s Manual (not shown)
* Standard Hardware Item - May be purchased locally.
† Stock item - May be secured through the Hardware Department of most
Sears retail stores.
• Any attempt to repair the control assembly or motor may create a hazard
unless repair is done by a qualified service technician. Repair service is
available at your nearest Sears store.

15
Notes ▬▬▬▬▬▬▬▬▬▬
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________

16
Notes ▬▬▬▬▬▬▬▬▬▬
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________
________________________

17
Manual de Uso y Cuidado
Use & Care Guide
Español / English
Model 758.15408010
Kenmore ®
P/ 1B72044 05/10
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A .
www.kenmore.com
www.sears.com
Humidificador Para Toda
La asa
Producción de 8 galones con lectura digital

18
Palabras de señal de seguridad
PELIGRO: Significa que si no se sigue la información
de seguridad, alguien resultará lesionado gravemente
o morirá.
ADVERTENCIA: Significa que si no se sigue la
información de seguridad, alguien podría resultar
lesionado gravemente o morir.
PRECA CIÓN: Significa que si no se sigue la
información de seguridad, alguien pudiera resultar
lesionado.
1. Para reducir el riesgo de peligro de incendio o
descargas eléctricas, enchufe el humidificador
directamente en un tomacorriente de 120 V .A.
No use cordones de extensión.
2. Mantenga el cable eléctrico alejado de las zonas
de tráfico. Para reducir el riesgo de peligro de
incendio, no ponga nunca el cordón eléctrico
debajo de alfombras ni cerca de salidas de calor,
radiadores de calor, estufas de cocina o
calentadores.
3. Desenchufe siempre el humidificador antes de
trasladarlo, antes de limpiarlo o siempre que no
esté en servicio.
4. Mantenga limpio el humidificador.
5. No ponga objetos extraños dentro del humidificador.
Información de garantía..........................................18
Instrucciones generales de seguridad....................18
Para ahorrarse una llamada de servicio.................19
Familiarícese con el humidificador .........................19
ómo funciona el humidificador .............................20
Paso 1. Preparación y puesta en
marcha del humidificador........................20
Paso 2. Instrucciones de ubicación........................21
6. No deje que el humidificador se use como un
juguete. Es necesario prestar mucha atención
cuando el humidificador sea usado por niños o
cerca de ellos.
7. No utilice nunca el humidificador mientras
alguna pieza falte o esté dañada de cualquier
manera.
8. Para reducir el riesgo de peligro eléctrico o
daños al humidificador, no incline, sacuda ni
vuelque el humidificador mientras la unidad
esté en marcha.
9. Para reducir el riesgo de daños al
humidificador, desenchúfelo cuando no esté
en uso.
10. Para reducir el riesgo de descargas eléctricas
accidentales, no toque el cable de
alimentación ni los controles con las manos
mojadas.
11. Fíjese en la etiqueta de advertencia que se
muestra a continuación.
onexión eléctrica............................................... 21
Paso 3. Llenado con agua ..................................22
Paso 4. Utilización de los controles...............23-24
Utilización del humidificador ..........................25-26
Reemplazo y cuidado del filtro............................ 26
Limpieza y mantenimiento .................................. 27
Resolución de problemas...............................28-29
Piezas de repuesto ........................................30-31
Índice ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
GARANTÍA COMPLETA DE N AÑO PARA EL H MIDIFICADOR
KENMORE
Si cualquier pieza de este humidificador falla debido a un defecto de material o de fabricación dentro
del plazo de un año a partir de la fecha de compra, o si el motor del humidificador falla debido a un
defecto de material o de fabricación durante el segundo año a partir de la fecha de compra,
DEVUELVA EL HUMIDIFI ADOR AL ENTRO DE PIEZAS Y REPARA IÓN DE SEARS MÁS
ER ANO y será reparado sin ningún cargo. Esta garantía no incluye los filtros del humidificador,
que son piezas perecederas que se pueden desgastar por causa del uso normal en menos de un
año. Esta garantía le confiere a usted derechos legales específicos y es posible que usted también
tenga otros derechos que varían de un estado a otro.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
INSTR CCIONES GENERALES DE SEG RIDAD
ADVERTENCIA:
Para reducir el riesgo de
incendio, descargas eléctricas o lesiones,
desenchufe siempre el humidificador antes
de hacerle servicio de ajustes y
reparaciones o limpiarlo.

19
ompruebe lo siguiente si el humidificador no
funciona.
1. ¿Está el cable de alimentación conectado a un
tomacorriente?
2. ¿Hay alimentación eléctrica al tomacorriente?
3. ¿Está el control de humedad ajustado a un nivel
lo suficientemente alto?
4. ¿Está el gabinete ubicado en una superficie
nivelada?
Para ahorrarse una llamada de servicio ▬▬▬▬▬▬▬
Familiarícese con el humidificador ▬▬▬▬▬▬▬▬▬
Descripción 758.15408010
* Producción en galones /24 h
apacidad de la botella
apacidad de la botella
* obertura en pies cuadrados
Velocidades del ventilador
Velocidad automática del ventilador
Filtro de repuesto
Higrostato automático
Apagado automático
ontroles
Pies de goma
atalogado por ETL
Voltaje
Frecuencia
Intensidad (alta velocidad)
Potencia (alta velocidad)
8 (30 litros)
1,2 galones (4,5 litros)
1,2 galones
1700 (158 m2)
3
Sí
32-15508
Sí
Sí
Electrónicos (pulsadores)
6
Sí
120 V .A.
60 Hz
1,2 A
80 W
* Basada en una zona con aislamiento promedio y una altura de habitación de 2,44 m (8 pies).
Quiet Comfort
Base
Botella
Asa de la botella
Filtro:
No. de repuesto
32-15508
Hygrostato
(En la cordón de
alimentación)
Conjunto del ventilador
Conjunto de
la carcasa
Controles de
velocidad y
humedad

20
Su nuevo humidificador Kenmore está diseñado para
satisfacer los requisitos de humedad del hogar a
través del principio de la evaporación del agua en el
aire. Una vez que el filtro se satura, se hace entrar
aire, el cual pasa a través del filtro y absorbe hume -
dad. Toda la evaporación ocurre en el humidificador,
por lo que todos los residuos permanecen en el filtro.
Este proceso natural de evaporación elimina
prácticamente el polvo blanco.
Una vez que haya sacado el humidificador de la caja de
cartón, quite todos los materiales de empaquetamiento.
Verifique que el filtro esté asentado apropiadamente
(consulte la página 26).
QuietComfort
Luego, se expulsa aire humidificado a través
de la parte superior
El aire seco
entra a través
de las rejillas
ubicadas
en la carcasa
Cómo funciona el humidificador ▬▬▬▬▬▬▬▬▬▬
PRECA CIÓN:
Para reducir el riesgo de
lesiones, incendio o daños al humidificador,
utilice únicamente limpiadores recomendados
específicamente para humidificadores. No
utilice nunca materiales inflamables,
combustibles o tóxicos para limpiar el
humidificador.
Para reducir el riesgo de quemarse y de
dañar el humidificador, no ponga nunca agua
caliente en el humidificador.
Paso 1.
Preparación y puesta en marcha
del humidificador
▬▬▬