Kensington KeyStand User manual

KeyStand™
Bluetooth® keyboard for iPad® family
QUICK START GUIDE
GUIDE DE DEMARRAGE RAPIDE
KURZANLEITUNG
SNELSTARTGIDS
GUIDA RAPIDA
GUÍA RÁPIDA
GYORSKALAUZ
PŘÍRUČKA ZAČÍNÁME
SZYBKI START
КРАТКОЕ РУКОВОДСТВО
ПОЛЬЗОВАТЕЛЯ
MANUAL DE INÍCIO RÁPIDO
Register Now!
Enregistrer maintenant !
Jetzt registrieren!
Nu registreren
Registrar ahora
Registra adesso
Regisztràljon most!
Zaregistrujte se nyní!
Zarejestruj się!
Зарегистрироваться!
Registe-se agora!
register.kensington.com
QUICK START GUIDE

2
AKeyStand Expert
BCharging Cable
CQuick Start Guide
DCaps Lock
EPower/Charging Indicator Light
FBluetooth Status Indicator Light
GOn/Off Switch/Bluetooth Connection Button
HMicroUSB Charging Connector
Contents
Components
English
F G
H
D E
QUICK START GUIDE
A
B
C

3
Attach Your iPad and Connect the Keyboard
1
2 Place your iPad on the ledge in either landscape or portrait orientation.
2 Press the On/Off Switch for 3 to 8 seconds. The Power Indicator Light glows.

4
NOTE: When you first turn on the Keyboard, both the Power Indicator Light and the
Bluetooth Status Indicator Light glow for 5 seconds. You cannot connect the Keyboard to
your iPad until only the Power Indicator Light glows.
3On your iPad, tap Settings.
4Open Bluetooth and make sure Bluetooth is on.
5On the Keyboard, press the Bluetooth Connection Button. The Bluetooth Status
Indicator Light starts blinking for 10 minutes or until connected to a device.
6The Keyboard now appears on your iPad screen. Tap Bluetooth Wireless Keyboard.
7Your iPad screen displays a passkey. Enter the passkey on the Keyboard, and press Enter.
8Your iPad screen shows the Keyboard as Connected. On the Keyboard, the Bluetooth
Status Indicator Light turns off.
9You can now use your Keyboard to type in any app.
NOTE: To insure the K Lock key works correctly please ensure you do the following:
Home page > Settings > General > Passcode key. Verify “Require Passcode” is set to
“Immediately” otherwise a keyboard unlock will not require a passcode. Go back to
previous menu and verify “Passcode Lock” is On.
Note the following about the Bluetooth connection between the keyboard and your iPad:
• KeyboardwillgointopairingmodeiftheOn/Off Switch press for 8 seconds or longer
then release (regardless of on or off state).
• PresstheOn/Off Switch for 3 to 8 seconds then release = toggle keyboard power (on
to off, off to on).
• Firstturn(Factorydefault,nopriorpairedBTdevices)–enterpairingmode
automatically.
• InONstateonly-Hold“CTRL + ALT + FN + F” for 3 seconds or more = reset to factory
default mode (clear all previously paired BT devices in memory), ALL LEDs should flash
on and off 3 times and keyboard should turn to off mode.
• Ifnoactivekeypressfor1minute,theunitshouldgotosleepmode.
• Anytimeakeyispressedinsleepmode,thekeyboardshouldautomaticallyconnectto
last paired iPad if present. If iPad is not found after waking from sleep mode within 30
seconds, the device should go back to sleep.

5
LED Behavior and Explanation
LED Behavior Explanation
• IftheKeyStandisoff,asleep,orthebatteryisdead,theLEDswillremain
off.
• Initiallyatpower-up,thePower and Bluetooth LEDs will turn on and stay
lit for 5 seconds.
• After5secondstheBluetooth LED will turn off, followed by the Power
LED 0.5s later.
• WhentheBluetooth Connection Button is pressed, the Power LED will
stay solidly lit, while the Bluetooth LED will begin to blink for 10 minutes
or until connected to an iPad.
• Blinkpattern:ON1s,OFF0.5s
• OncetheKeyStandisconnectedwithyouriPad,thePower LED will
remain lit and all others will go off.
• Also,iftheKeyStandisawokenfromsleepmode,thePower LED will turn
on immediately.
• WhiletheKeyStandisconnectedtoyouriPad,thestateoftheCapsLock
toggle is shown by the Caps Lock LED.
• WhentheKeyStandispluggedintoapowersource,theCharge LED will
turn flash red and turn off only when charge is completed.
Charge the Battery
Charge your KeyStand Expert before initial use or when the Charging Indicator glows red.
1Insert the small end of the Charging Cable into the micro USB Charging Connector on
the Keyboard.
2Insert the other end of the Charging Cable into your iPad charger.
3Plug your iPad charger into a working outlet. The Charging Indicator Light
glows red.
4When the Keyboard is fully charged, the Charging Indicator Light turns off.

6
Troubleshooting
I can’t connect the Keyboard to my iPad.
Try the following in sequence. You can stop when the problem is fixed.
1Make sure you have installed and set up Bluetooth correctly on your iPad. Check the
documentation that came with your iPad for instructions.
2Make sure that the Keyboard is within range of your iPad. Maximum Bluetooth range
is about 10 meters/33 feet.
3If your iPad is connected to other Bluetooth devices, you may need to disconnect
some devices before you can connect to the Keyboard.
4If you changed any Bluetooth settings on your iPad, try connecting the Keyboard to
your iPad again.
5Make sure that both your iPad battery and the Keyboard battery are sufficiently
charged.
If this does not solve the problem, please contact Kensington Support at kensington.com.
Technical Support
Technical support is available to all registered users of Kensington products. Technical
Support contact information can be found on the back page of this manual.
Web Support
You may find the answer to your problem in the Frequently Asked Questions (FAQ) section
of the Support area on the Kensington Website: www.support.kensington.com.
Telephone Support
There is no charge for technical support except long-distance charges where applicable.
Please visit www.kensington.com for telephone support hours. In Europe, technical
support is available by telephone Monday to Friday 09:00 to 21:00 (Central European
time).
Please note the following when calling support:
• Callfromaphonewhereyouhaveaccesstoyourdevice.
• Bepreparedtoprovidethefollowinginformation:
 – Name,address,andtelephonenumber
 – NameoftheKensingtonproduct
 – Makeandmodelofyourcomputer
 – Systemsoftwareandversion
 – Symptomsoftheproblemandwhatledtothem
WARNING! IMPORTANT SAFETY INSTRUCTIONS
Failure to read and follow these safety instructions could result in fire, explosion, electrical
shock or other hazard, causing serious and/or fatal injury and/or property damage.
• Donotmodify,disassemble,open,drop,crush,puncture,orshredtheKeyStand.
• TheKeyStandcontainsalithium-polymerbattery,whichisflammable.Keepawayfromopen
flame.
• Topreventshortcircuitorotherpotentialhazards,preventmetalobjectssuchascoinsorkeys
fromcomingintocontactwiththeKeyStand,anddonotinsertforeignobjectsintotheKeyStand
or its ports.
• KeepyourKeyStanddry,anddonotusewithwethands.MoistureinorontheKeyStandmaylead
to electrical shock. If exposed to moisture during use, unplug the KeyStand immediately. If your

7
KeyStand gets wet, have a qualified technician evaluate the product’s safety before resuming use.
• YourKeyStandmaybecomewarmduringoperation.Thisisnormal.However,toprevent
overheating, keep area around KeyStand ventilated and do not place anything on or around
KeyStand during operation. Do not operate your KeyStand near a heat source, heat vent, or in
directsunlight.YourKeyStandshouldbeusedintemperaturesbetween50–80°F(10–27°C).
• IftheKeyStandbeginstoswellorexpand,emitsastrongodor,orbecomeshottothetouch,
discontinue use of the KeyStand, and have the product examined by a qualified electronic
technician.
• InspectyourKeyStandandcablesfordamagebeforeuse.Haveanydamagedpartrepairedor
replaced before use.
• YourKeyStandisnotuserserviceable.Donotattempttoopen,modify,orrepair.
• IfthebatteryinsidetheKeyStandleaksforanyreason,discontinueuse,anddonotallowthe
KeyStand’s contents to contact your skin or eyes. In the event of accidental contact wash the
affected area with large amounts of water and seek medical attention immediately.
• YourKeyStandisnotatoy.Keepthemawayfromchildren.Insurethatallpersonswhousethis
product read and follow these warnings and instructions.
• DonotleavetheKeyStandonprolongedchargewhennotinuse.
Enhancing Performance by Proper Care and Storage of your KeyStand
• DonotstoreyourKeyStandeitherfullychargedordischarged.ItisbesttostoreyourKeyStand
with at least 30 % charge remaining. To check the charge level of your KeyStand press the battery
indicator button.
• AvoidfrequentfulldischargesbecausethisputsadditionalstrainonthebatteryintheKeyStand.
Charge your KeyStand between uses even if it is not fully discharged. The lithium-polymer battery
used in this product has no “memory effect.” Therefore, several partial discharges with frequent
recharges are better than one full discharge, and will help prolong the life of your KeyStand. Short
battery life in laptops is mainly caused by heat, rather than charge/discharge patterns.
•
Do not store your KeyStand at elevated temperatures (such as in your car) or in high humidity.
Disposing of your KeyStand
• DonotincinerateordisposeofyourKeyStandinafireormicrowave.
• DonotdisposeofyourKeyStandasordinaryrefuse,asitcontainsalithium-polymerbattery.
Consult your local municipal or civil authority for instructions on correctly disposing of a
lithium-polymer battery.
• IntheUSAandCanada:Thismark indicates your KeyStand can be recycled by the
Rechargeable Battery Recovery Corporation (“RBRC”). When you are ready to dispose of the
KeyStand, please contact the RBRC at 1-800-8-BATTERY or www.rbrc.org.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses. and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
MODIFICATIONS: Modifications not expressly approved by Kensington may void the user’s authority to operate the
device under FCC regulations and must not be made.
SHIELDED CABLES: In order to meet FCC requirements, all connections to equipment using a Kensington input device
should be made using only the shielded cables.
FCC DECLARATION OF CONFORMITY COMPLIANCE STATEMENT
ThisproductcomplieswithPart15oftheFCCrules.Operationissubjecttothefollowingtwoconditions:(1)This
device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation. As defined in Section 2.909 of the FCC Rules, the responsible party

8
for this device is Kensington Computer Product Group, 333 Twin Dolphin Drive, Redwood Shores, CA 94065,USA.
INDUSTRY CANADA CONFORMITY
ThisdevicehasbeentestedandfoundtocomplywiththelimitsspecifiedinRSS-210.Operationissubjecttothe
following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES-003.
CE DECLARATION OF CONFORMITY
Kensington declares that this product is in compliance with the essential requirements and other relevant provisions
of applicable EC directives. For Europe, a copy of the Declaration of Conformity for this product may be obtained by
clicking on the Compliance Documentation link at www.support.kensington.com.
INFORMATION FOR EU MEMBER-STATES ONLY
The use of the symbol indicates that this product may not be treated as household waste. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For
more detailed information about recycling of this product, please contact your local city office, your
household waste disposal service, or the shop where you purchased the product.
Kensington and the ACCO name and design are registered trademarks of ACCO Brands. The Kensington Promise is a
service mark of ACCO Brands. KeyStand is a registered trade mark of ACCO Brands. iPod is a trademark of Apple Inc.,
registered in the U.S. and other countries. iPhone is a trademark of Apple Inc. “Made for iPod” means that an electronic
accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple
performance standards. “Works with iPhone” means that an electronic accessory has been designed to connect
specifically to iPhone and has been certified by the developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with safety and regulatory standards. All other registered
and unregistered trademarks are the property of their respective owners.
© 2012 Kensington Computer Products Group, a division of ACCO Brands USA LLC. Any unauthorized copying,
duplicating, or other reproduction of the contents hereof is prohibited without written consent from Kensington
Computer Products Group. All rights reserved. 01/12

901-2582-00
KL
Kensington Computer Products Group
A Division of ACCO Brands
333 Twin Dolphin Drive, Sixth floor
Redwood Shores, CA 94065
Designed in California, U.S.A.
by Kensington
Made in China
ACCO Brands Europe
Oxford Road
Aylesbury
Bucks, HP21 8SZ
United Kingdom
www.kensington.com
Patents Pending
For technical support visit:
Pour tout support
technique veullez visiter:
www.kensington.com
Complete warranty terms are available at:
www.warranty.kensington.com
ACCO Australia
Level 2, 8 Lord St
Botany NSW 2019
Australia
Technical Support / Assistance technique / Technischer Support / Technische
ondersteuning / Supporto tecnico / Asistencia técnica / Műszaki támogatás / Technická
podpora / Pomoc techniczna / Техническая поддержка / Assistência técnica
België / Belgique 02 275 0684 Nederland 053 482 9868
Canada 1 800 268 3447 Norway 22 70 82 01
Denmark 35 25 87 62 Österreich 01 790 855 701
Deutschland 0211 6579 1159 Portugal 800 831 438
España 91 662 38 33 Russia 007 495 933 5163
Finland 09 2290 6004 Schweiz / Suisse 01 730 3830
France 01 70 20 00 41 Sweden 08 5792 9009
Hungary 20 9430 612 United Kingdom 0207 949 011
Ireland 01 601 1163 United States 1 800 535 4242
Italia 02 4827 1154 International Toll [phone]
México 55 15 00 57 00