Kenwood CMOS-320 User manual

CMOS-320
CMOS-220
UNIVERSAL MULTI-VIEW CAMERA/ UNIVERSAL REAR VIEW CAMERA
INSTRUCTION MANUAL
CAMÉRA MULTI-VUES UNIVERSELLE/ CAMÉRA DE RECUL UNIVERSELLE
MODE D’EMPLOI
UNIVERSAL MULTIVIEW-KAMERA/ UNIVERSAL RÜCKFAHRKAMERA
BEDIENUNGSANLEITUNG
UNIVERSELE MULTIVIEWCAMERA/ UNIVERSELE ACHTERUITRIJCAMERA
GEBRUIKSAANWIJZING
LYT2720-001A (W)
© 2014 JVC KENWOOD Corporation
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance
from your new Universal Camera.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card,
and in the space provided below. Refer to the model and serial numbers whenever you call upon your
Kenwood dealer for information or service on the product.
Model CMOS-320/CMOS-220 Serial number
US Residence Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
LVT2720-001A.indb 1 14/02/14 15:09

2|CMOS-320/CMOS-220
• Beforenallyinstallingtheunit,connectthewiring
temporarily,makingsureitisallconnectedupproperly,
andtheunitandthesystemwork.
• Whenmountingthisunit,makesurenoneoftheleadsare
trappedbetweenthisunitandthesurroundingmetalwork
orttings.
• Donotmountthisunitneartheheateroutlet,where
itwouldbeaectedbyheat,ornearthedoors,where
rainwatermightsplashontoit.(Neverinstallinlocations
suchastheabovebecauseofthedangerofmalfunction
duetohightemperatures.)
• Beforedrillinganymountingholesalwayscheckbehind
whereyouwanttodrilltheholes.Donotdrillintothegas
line,brakeline,electricalwiringorotherimportantparts.
• Ifthisunitisinstalledinthepassengercompartment,
anchoritsecurelysoitdoesnotbreakfreewhilethecaris
moving,andcauseinjuryoranaccident.
• Ifthisunitisinstalledunderafrontseat,makesureitdoes
notobstructseatmovement.Routeallleadsandcords
carefullyaroundtheslidingmechanismsotheydonotget
caughtorpinchedinthemechanismandcauseashort
circuit.
Care and maintenance
• Whentheproductgetsdirty,wipedrywithasiliconcloth
orsoftcloth.Ifitisseriouslystained,removestainwith
aclothmoistenedwithaneutralcleanerandthenwipe
thecleaneraway.Donotuseahardclothand/oravolatile
substancesuchaslacquerthinneroralcohol,scratches,
deformation,degradationand/ordamagemayresult.
• Whenalenscomponentgetsdirty,wipegentlywithasoft
clothmoistenedwithwater.Donotrubwithadryclothto
preventscratchingthelens.
Installation Procedure
1 Topreventashortcircuit,removethekeyfromthe
ignitionanddisconnectthe-battery.
2 Maketheproperinputandoutputwireconnections
foreachunit.
3 Connectthewiringharnesswiresinthefollowing
order:ground,ignitionandcameraunit.
4 Installtheunitinyourcar.
5 Reconnectthe-battery.
WARNING
To prevent injury or fire, take the following
precautions:
• Topreventashortcircuit,neverputorleaveanymetallic
objects(suchascoinsormetaltools)insidetheunit.
• Installationandwiringofthisproductrequirespecialist
skillandexperience.Toassureyoursafety,pleaserequesta
specialisttechniciantoinstalltheunit.
• Whenyoumakeaholetoinstallthecamera,checkthe
locationofpipes,tanksandwiringandavoidtouching
them.Otherwiseitmaycausethere.
• Whenyoumakeaholewithadrill,usegogglestoprotect
youreyes.
CAUTION
To prevent damage to the product, take the
following precautions:
• Makesuretogroundtheunittoanegative12VDCpower
supply.
• Whenreplacingafuse,onlyuseanewfusewiththe
prescribedrating.Usingafusewiththewrongratingmay
causeyourunittomalfunction.
• Donotuseyourownscrews.Useonlythescrewsprovided.
Ifyouusethewrongscrews,youcoulddamagetheunit.
NOTE
• Arearviewcameraisacamerathatprovidessymmetrical
imagesinthesamewayasrearandsideviewmirrors.
• ConnectiontoaTVwithanRCAvideoinputispossible,
butconrmwhethertheTVyouusehasareversegear
connectionfunction.
• Thisproductisdesignedtosupplementthedriver’srear
view,butthecameraimagesdonotshowalldangersand
obstacles.Besuretolookbehindyouwhenreversingto
conrmtheview.
• Thisproductfeaturesawide-anglelens,sothenearview
iswideandthefarviewisnarrow,whichmaycreatea
falsesenseofdistance.Besuretolookbehindyouwhen
reversingtoconrmtheview.
• Donotwashyourcarwithanautomaticcarwashor
high-pressurewaterasitmayresultinwaterenteringthe
cameraorthecamerafallingo.
• Checkcamerabracketinstallationbeforedriving.
 Arethescrewsloose?
-Isthecamerabracketrmlysecured?
-Iftherearviewcameracomesloosewhileyouaredriving
itmaycauseanaccident.
Before Use/ Installation Procedure
LVT2720-001A.indb 2 14/02/14 15:09

CMOS-320/CMOS-220 |3
ENGLISH
• Laythecordsbyavoidinghigh-temperatureareas.Use
corrugatedtubesforwiringinsidetheengineroom.Ifa
cordcontactsahigh-temperatureareaofthevehicle,the
coatingmaymeltandcauseshort-circuiting,whichmay
leadtoareorelectricshockhazard.
Accessories
Before Use/ Installation Procedure
WARNING
• Ifyouconnecttheignitionwire(Red)tothecarchassis
(Ground),youmaycauseashortcircuit,thatinturnmay
startare.Alwaysconnectthosewirestothepowersource
runningthroughthefusebox.
• Donotcutoutthefusefromtheignitionwire(Red).The
powersupplymustbeconnectedtothewiresviathefuse.
CAUTION
• Ifyourcar’signitiondoesnothaveanACCposition,connect
theignitionwirestoapowersourcethatcanbeturnedon
andowiththeignitionkey.Ifyouconnecttheignition
wiretoapowersourcewithaconstantvoltagesupply,as
withbatterywires,thebatterymaydie.
• Ifthefuseblows,rstmakesurethewiresaren’ttouching
tocauseashortcircuit,thenreplacetheoldfusewithone
withthesamerating.
• Insulateunconnectedwireswithvinyltapeorothersimilar
material.Topreventashortcircuit,donotremovethecaps
ontheendsoftheunconnectedwiresortheterminals.
• Aftertheunitisinstalled,checkwhetherthebrakelamps,
blinkers,wipers,etc.onthecarareworkingproperly.
• Installsothatitdoesnotobstructthereareldofview.
• Installsothatitdoesnotprotrudefromthesideofthecar.
• Donotperforminstallationinrainorfog.
• Whenhumidityishigh,drythesurfacetowhichtheunitis
tobeattachedbeforeinstalling.
• Moistureontheattachmentsurfacereducesadhesive
strength,whichmayleadtotheunitcomingo.
• Donotattachthecamerabrackettoareasonthecarbody
treatedwithuorocarbonresin,orglass.
• Mayresultintherearviewcamerafallingo.
- Donotapplywatertotheunit.
- Donotexposetheunittorain.
- Donotsubjectthecameratounnecessaryforce.
- Thoroughlycleanwheretapeisusedforstickingonthe
unit.
• RefertotheInstruction’smanualfordetailsonconnecting
theotherunits,thenmakeconnectionscorrectly.
• Securethewiringwithcableclampsoradhesivetape.
Toprotectthewiring,wrapadhesivetapearoundthem
wheretheylieagainstmetalparts.
• Routeandsecureallwiringsoitcannottouchanymoving
parts,suchasthegearshift,handbrakeandseatrails.
• Donotroutewiringinplacesthatgethot,suchasnearthe
heateroutlet.Iftheinsulationofthewiringmeltsorgets
torn,thereisadangerofthewiringshort-circuitingtothe
vehiclebody.
• Whenreplacingthefuse,besuretouseonlyfuseofthe
ratingprescribedonthefuseholder.
• TominimizenoiselocatetheTVantennacable,radio
antennacableandRCAcableasfarawayfromeachother
aspossible.
Grommet..........1
Camerabracketclampingscrew..........1
Camera(withcamerabracket)..........1
Switchunit..........1
Double-sideadhesivetape..........1
CMOS-320 only
Powercord..........1
CMOS-320  CMOS-220
LVT2720-001A.indb 3 14/02/14 15:09

4|CMOS-320/CMOS-220
CAUTION
•Theadjustmentsduringcamerasettingmaybehindered
dependingonthecamerainstallationposition.Donot
installthecamerasecurelybutattachitonlytemporarily
untilthecamerasettinghascompleted.
Recommended Installation Position
Examples of correct camera installation on the
rear of the vehicle
Installation position
The CMOS-320 should be installed at a height of 50 cm (1.64
feet) or more.
Mount so that the “KENWOOD”
logo appears at the top.
Examples of correct camera installation on the
front of the vehicle (CMOS-320 only)
The CMOS-320 should be installed at a height of 30cm to 80cm
(0.98feet to 2.62feet).
Mount so that the “KENWOOD”
logo appears at the top.
Installation position (standard)
Installation position (lower)
Installing the Camera/Adjusting its
angle
1Decide the camera installation position.
2Clean the camera installation surface.
Using a commercially available cleaner, wipe dirt, moisture
and oil away from the surface on which the camera bracket
is to be attached.
3Loosen the camera bracket retaining screws.
Using a commercially available
Phillips screwdriver, loosen the
two retaining screws.
Perform steps 4 and 5 only when they are required.
4If required, separate the camera bracket from
the camera and adjust the shape according to
the surface on which it will be attached.
Bend
Bend
Camera bracket
Adjust the camera bracket
shape so that it fits the
camera installation
position.
5Mount the camera on the camera bracket.
Mount so that the “KENWOOD” logo appears at the top.
6Fix the camera temporarily with tape, etc.
Using a piece of tape, etc., fix the camera temporarily.
12345
Install the camera at the center of the vehicle and not to
hide the number plate. And also install straight toward the
forward/reverse direction of the vehicle. Be careful not to
lean the camera toward other directions of the vehicle, etc.
7Complete all of the required connections.
Installation
LVT2720-001A.indb 4 14/02/14 15:10

CMOS-320/CMOS-220 |5
ENGLISH
Installing the Camera/Adjusting its
angle
1Decide the camera installation position.
2Clean the camera installation surface.
Using a commercially available cleaner, wipe dirt, moisture
and oil away from the surface on which the camera bracket
is to be attached.
3Loosen the camera bracket retaining screws.
Using a commercially available
Phillips screwdriver, loosen the
two retaining screws.
Perform steps 4 and 5 only when they are required.
4If required, separate the camera bracket from
the camera and adjust the shape according to
the surface on which it will be attached.
Bend
Bend
Camera bracket
Adjust the camera bracket
shape so that it fits the
camera installation
position.
5Mount the camera on the camera bracket.
Mount so that the “KENWOOD” logo appears at the top.
6Fix the camera temporarily with tape, etc.
Using a piece of tape, etc., fix the camera temporarily.
12345
Install the camera at the center of the vehicle and not to
hide the number plate. And also install straight toward the
forward/reverse direction of the vehicle. Be careful not to
lean the camera toward other directions of the vehicle, etc.
7Complete all of the required connections.
8Display the camera video.
Before viewing the camera, apply the parking brake
and chock the wheels so that the vehicle will not move.
Otherwise, an unexpected accident may result.
For displaying the camera video, read the instruction manual
for your video monitor.
When the camera is installed as a rearview
camera:
Change the shift lever to the R (Reverse) range
to view the image of the rear of the vehicle.
When the camera is installed as a front camera
(CMOS-320 only):
Refer to the instruction manual of the unit that
you have connected this camera to, and display
the image of the front of the vehicle.
9Adjust the camera angle.
When adjusting the camera angle, be careful not to stretch
the camera cord.
When installing CMOS-220 as a rearview
camera:
Adjust the angle so that the rear of the vehicle or the bumper
can be seen at the bottom of the monitor.
Vehicle rear part or bumper
When installing CMOS-320 as a rearview
camera:
Refer to “Display View Switching” (page 14) and switch the
image to [Overhead View]. Adjust the camera angle so that
the guideline and the parking lines become vertical.
Guideline
Installation
When installing CMOS-320 as a front camera:
Before adjusting the camera angle, perform “Camera ID
Setting” (page 13) and “Camera Setting Procedure” (page
10).
When you select [Standard] for “Mounting Position Setting”,
switch the image to [Overhead View] (page 14) and adjust
the camera angle so that the guideline and the parking lines
become vertical.
When you select [Lower] for “Mounting Position Setting”,
switch the image to [Corner View] (page 14) and then adjust
the angle of the camera to straighten the ground lines in the
left and right screens.
10Set the camera.
When using CMOS-320 as a rearview camera:
Refer to page 9 to 13 and perform “Preparation Before
Camera Setting”, “Overhead View Image Adjustment” and
“Wide View Guideline Adjustment”.
When using CMOS-320 as a front camera:
When you select [Standard] for “Mounting Position Setting”,
refer to page 9 to 13 and perform “Preparation Before Camera
Setting”, “Overhead View Image Adjustment” and “Wide
View Guideline Adjustment”.
When you select [Lower] for “Mounting Position Setting”,
refer to page 9 to 13 and perform “Preparation Before Camera
Setting” and “Overhead View Image Adjustment”. You cannot
perform “Wide View Guideline Adjustment”.
11 After adjusting the camera angle, tighten the
retaining screws firmly.
Inspect the retaining screws at times. If they are loose,
tighten them firmly.
Next page 3
LVT2720-001A.indb 5 14/02/14 15:10

6|CMOS-320/CMOS-220
Enginekey
Camera
12 Fix the camera firmly in position.
Peel off the paper liner from the double-side adhesive tape
on the camera bracket and attach it. After attaching, push the
camera bracket with your finger to ensure close adhesion.
Do not touch the adhesive surface with your hand or peel and
reattach an attached tape, as these will degrade the adhesive
force and may cause the camera bracket to be detached. If
required, secure the bracket on the vehicle body using the
camera bracket clamping screw.
The camera bracket has two holes for the screw. Select one of
them to fit the position of the attachment.
Camera bracket clamping screw
(M3 x 8mm)
Installing the Switch Unit
(CMOS-320 only)
1Clean the switch unit installation surface.
Using a commercially available cleaner, wipe dirt, moisture
and oil away from the surface on which the switch unit is to
be attached.
2Attach double-side adhesive tape on the
bottom of the switch unit and then attach it in
an easy-to-operate position, for example near
the dashboard on the driver seat side.
When using the camera as a front camera and with a
Kenwood navigation system, this switch unit is used only for
the ID setting of the CMOS-320 unit. So you do not have to
attach the switch unit with double-side adhesive tape. For
the ID setting, see “Camera ID Setting”(page 13)
Installation
LVT2720-001A.indb 6 14/02/14 15:10

CMOS-320/CMOS-220 |7
ENGLISH
Videocord
Navigationsystem/videomonitor(separatelyavailable)
GNDcord(Black)
Accessorycord(Red)
GND
Battery
Mainfuse
Fuse
Enginekey
Connecttoametallicpartofvehicle(apartofchassisconnectedtothe
negativesideofpowersupply).
CAUTION
•IftheenginekeyofyourvehicledoesnothavetheACCposition,branchthewireenergizedwhentheenginekeyisONand
connectittotheaccessorypowercord.
•Beforeproceedingtoconnections,makesurethattheenginekeyisnotinsertedanddisconnectthe(-)terminalofthebattery
topreventtheshort-circuitingincident.
ConnecttotheON-OFFswitchablepowersupply.
DonotconnecttoapermanentlyONpowersupply.
Fuse(2A)
Camera
Connectthecameratothecameraconnectioncord.
Connecttotherearviewcameravideoinputortotheexternal
videoinputofthevideomonitor.
Powercord
Accessorypower(ACC)
Switchunit(CMOS-320only):1m(3.28feet)
Basic Connections
Camera’scordlength:1.5m(4.92feet),
Powercord:7.5m(24.6feet)
Connections
CAM+(Green/red)
CAM-(Green/white)
LVT2720-001A.indb 7 14/02/14 15:10

8|CMOS-320/CMOS-220
Videocord
Videocord
Camera1(Usedasrearviewcamera)
Camera2(Usedasfrontviewcamera)
Connecttothededicatedrearviewcameravideo
input.
Connecttotheexternalvideoinput.Selectthe
externalvideoinputtocheckthecameraimage.
Connecttothecamera
controlterminalsofthe
controlunit.
CAM+(Green/red)
CAM-(Green/white)
Connection of 2 Cameras
Powercord
System Connection (CMOS-320 only)
Powercord
Topowersupply
•WhenconnectingthecameratoaKenwoodnavigationsystemetc,(Controlunit)equippedwiththecameracontrolfunction,use
theprovidedcontrolunitconnectioncord.Thisallowsthecontrolunittoswitchthedisplayviewandadjustthecameraaswell
ontouchthecontrolunitscreen.
•WhenusingtwoCMOS-320units(forthefrontandrear),itisrequiredtosetanIDforthefrontcamera.Fordetails,see“Camera
IDSetting”(page13).
•Connectthepowersupplyinthesamewayas“BasicConnections”.
•Theprovidedswitchunitisnotusedinthesystemconnection.
LVT2720-001A.indb 8 14/02/14 15:10

CMOS-320/CMOS-220 |9
ENGLISH
Switch Unit Operation
Theswitchunitcanbeusedtoswitchtheimagedisplay
mode,view/hidetheguidelinedisplayandadjustthe
camera.
View button
•Switchestheimagedisplaymode.
•Selectaniteminthesettingmode.
•Pressandholdtodisplayorhidetheguidelines.
+/− button
Movesacrossthesettingmode
itemsorsetsanadjustmentvalue.
Preparation Before Camera Setting
When the camera is installed as a rearview
camera:
1Stop the vehicle.
In a parking space with white lines and tire stoppers, park the
vehicle in the center of the white line frame.
2Advance the vehicle.
• Move the vehicle forward until the entire parking space can
be viewed in the camera image.
• Be sure to apply the parking brake and push the brake
pedal so that the vehicle is completely stationary. Perform
the setting in a place that will not cause nuisance to other
people.
When installing the front camera at a height of
50cm (1.64 feet) or more:
Prepare as same as the rearview camera.
When installing the front camera below 50cm in
height:
1Install the camera at the center of the vehicle
(page 4).
• If not, the image may not be symmetric in the “Corner
View”.
2Move the vehicle on the center of the parking
line.
• You can use a long stick instead of the parking line if you
can not use the 2 parking lots etc.
• Be sure to apply the parking brake and push the brake
pedal so that the vehicle is completely stationary. Perform
the setting in a place that will not cause nuisance to other
people.
3Set the camera.
Adjust the “Overhead View Image Adjustment” (page 10, 11)
so that the parking line is displayed vertically in the center.
Camera Setting (CMOS-320 only)
LVT2720-001A.indb 9 14/02/14 15:10

10 |CMOS-320/CMOS-220
Camera Setting Procedure
1Complete all of the required connections in
advance.
2Display the camera video.
For displaying the camera video, read the instruction manual
for your video monitor.
3Press and hold the view and + buttons of the
switch unit simultaneously to enter the camera
adjustment mode.
4First select the positioning of the camera.
Use the + or – button to select an item and press the view
button to enter the selection.
•Whenusingthecameraastherearviewcamera,select
[OK].Andthengotostep6.
•Whenusingthecameraasthefrontcamera,select
[Normal]andthenselect[OK].Andthengotostep5.
•Selecting[ResetAll]resetsallofthecamerasettings
tothedefaults.
5Adjust the camera’s mounting position with
the + or – buttons on the switch unit.
Select [Standard] when installing the camera at a height of
50cm to 80cm (1.64feet to 2.62feet).
Select [Lower] when installing the camera at a height of
30cm to below 50cm (0.98feet to below 1.64feet).
6Select a camera adjustment item and adjust it.
The following items are available for camera adjustment.
1. Overhead view image adjustments
(Centering, Right-and-Left angle, Up-and-Down Angle)
2. Wide view guideline adjustments
(Size, Horizontal direction, Red Line Position Setting)
To select an item:
Press the + or – button to select an item and press the view
button to enter the selection. When an adjustment item is
selected, the frame of its icon turns from blue to yellow.
To adjust the item:
After selecting the item, press the + or – button to adjust it
and press the view button to enter the adjusted value.
7End the setting.
Overhead View Image Adjustment
(Centering)
Thisitemadjuststhecenterofthecamerainstallation
position.
1Select “OVERHEAD VIEW IMAGE ADJUSTMENT
(CENTERING)”.
2Press the + or – button of the switch unit so
that the two white lines appear on the position
corresponding to the center line of the vehicle.
Adjustment is possible by two steps to the left and right.
If the adjustment is not possible in the currently available
range, change the camera position before retry.
•Select[Back]togobacktothepreviousadjustment
item.
•Select[Next]toadvancetothenextadjustmentitem.
•Selecting[Reset]inanindividualadjustmentitem
resetsthecamerasettingofthatitemtothedefault.
Camera Setting (CMOS-320 only)
LVT2720-001A.indb 10 14/02/14 15:10

CMOS-320/CMOS-220 |11
ENGLISH
•Select[ ]toinverttheiconupsidedown.
3After completing the adjustment, press the
view button.
Advances to “OVERHEAD VIEW IMAGE
ADJUSTMENT (Right-and-Left ANGLE)”.
Overhead View Image Adjustment
(Right-and-Left Angle)
Thisitemadjuststhehorizontalangle(intherotary
direction)ofthecamerainstallationposition.
1Select “OVERHEAD VIEW IMAGE ADJUSTMENT
(Right-and-Left ANGLE)”.
2Press the + or – button of the switch unit
so that the center of the parking space is
displayed vertically.
Adjustment is possible by one step to the left and right. If the
adjustment is not possible in the currently available range,
change the camera position before retrying.
3After completing the adjustment, press the
view button.
Advances to “OVERHEAD VIEW IMAGE
ADJUSTMENT (Up-and-Down ANGLE)”.
Overhead View Image Adjustment
(Up-and-Down Angle)
Thisitemadjuststheverticalangle(inclination)ofthe
camerainstallationposition.
1Select “OVERHEAD VIEW IMAGE ADJUSTMENT
(Up-and-Down ANGLE)”.
2Press the + or – button of the switch unit so
that the lines indicating the vehicle width are
shown vertical.
Adjustment is possible by one step up and down. If the
adjustment is not possible in the currently available range,
change the camera position before retrying.
3After completing the adjustment, press the
view button.
4Select [Next].
Advances to “GUIDELINE ADJUSTMENT (Size)”.
Camera Setting (CMOS-320 only)
LVT2720-001A.indb 11 14/02/14 15:10

12 |CMOS-320/CMOS-220
For Guideline Adjustment
• The subsequent adjustments adjust the sizes, lengths and positions
of the guidelines displayed in the wide view and overhead view.
By default, guidelines shown below are displayed assuming that
the camera installation height is 80 cm (2.62 feet) and that the
distance between the left and right lines of the parking space is 2.2
meters (7.22 feet).
• The red line is used to indicate the parking position and can set it
independently from other guide lines.
Green
Red
2.7m
(8.86feet)
2.2m(7.22feet)
Wide View Guideline Adjustment (Size)
Thisitemadjuststheoverallsizeofguidelinesdisplayedin
thewideview.
1Select “GUIDELINE ADJUSTMENT (Size)”.
2Press the + or – button of the switch unit to
adjust the size.
3After completing the adjustment, press the
view button.
Advances to “GUIDELINE ADJUSTMENT
(Horizontal direction)”.
Wide View Guideline Adjustment
(Horizontal Direction)
Thisitemadjuststheleft-rightpositioningofthe
guidelinesdisplayedinthewideview.
1Select “GUIDELINE ADJUSTMENT (Horizontal
direction)”.
2Press the + or – button of the switch unit to
adjust the left-right positioning.
3After completing the adjustment, press the
view button.
Advances to “GUIDELINE ADJUSTMENT (Red Line
Position Setting)”.
Camera Setting (CMOS-320 only)
LVT2720-001A.indb 12 14/02/14 15:10

CMOS-320/CMOS-220 |13
ENGLISH
Wide View Guideline Adjustment
(Red Line Position Setting)
Thisitemadjuststhepositionoftheredlinedisplayedin
thewideview.Theredlinecanbeusedindependentlyto
setthereferencelineforthevehicleparkingposition.
1Select “GUIDELINE ADJUSTMENT (Red Line
Position Setting)”.
2Press the + or – button of the switch unit to
adjust the position of the red line.
Move the red line until the edge of your vehicle’s bumper.
If the edge of your vehicle’s bumper cannot be seen in the
monitor, move the red line around the edge of your vehicle.
3After completing the adjustment, press the
view button.
4Select [Next].
Advances to “SETTING COMPLETE”.
Finishing the Camera Setting
1Press the + or – button of the switch unit to
select [Finish] and press the view button.
Camera Setting (CMOS-320 only)
Camera ID Setting
WhenconnectingaCMOS-320asafrontcameratoa
Kenwoodnavigationsystemequippedwiththecamera
controlfunction,itisrequiredtoassigntheIDto[Front
Camera].
1Install the switch unit.
Refer to “Basic Connections” (page 7) for the connection.
2Display the image of the front camera on the
monitor of the Kenwood navigation system.
For displaying the image, refer to the instruction manual of it.
3Press and hold the + button of the switch unit
for more than 2 seconds, and then press and
hold the – button for more than 2 seconds.
4Press the + or – button of the switch unit
to select the camera ID, and press the view
button.
5After setting, press the + or – button of the
switch unit to select [Finish] and press the view
button.
6Turn off the ACC.
7Disconnect the switch unit.
8Connect CAM+/CAM– to the Kenwood car
navigation system.
9Turn on the ACC.
LVT2720-001A.indb 13 14/02/14 15:10

14 |CMOS-320/CMOS-220
Display View Switching (CMOS-320 only)
Display View Switching
TheCMOS-320camerasystemcandisplay4kindsofcamera
images.
1With an image displayed on the monitor, press
the view button of the switch unit.
Each press switches the image display mode in the following
order.
Ultra Wide View
Wide-angle image covering a horizontal angle of about 195°.
Wide View
Camera image covering a horizontal angle of about 135°.
Overhead View
Image seen from the viewpoint straight up above the vehicle.
Depending on the camera installation position, the Overhead
View image may not be displayed correctly.
• Overhead View may appear twice, depending on the
connected navigation system.
Corner View
The views seen from the two corners of vehicle are displayed
on the left and right halves of the screen.
When connecting the camera to a Kenwood navigation
system etc, (Control unit) equipped with the camera control
function, use the provided control unit connection cord. This
allows the control unit to switch the display view as well on
touch the control unit screen (page 8).
LVT2720-001A.indb 14 14/02/14 15:10

CMOS-320/CMOS-220 |15
ENGLISH
Camnit (CMOS-320)
Outputvideo
: Wide-angle mirror image (for rearview)/wide-
angle normal image (for front view)
Sensor:1/3.6-inch color CMOS sensor
Numberofpixels: Approx. 330,000 pixels
Lens
: Wide angle, Focal length f=1.05 mm, F value 2.0
Anglesofview
: Horizontal: Approx. 195°
: Vertical: Approx. 145°
Videooutput: 1.0Vp-p/ 75Ω
Illuminationrange: Approx. 0.9 to 100,000 lux
Irissystem: Electronic iris
Scanningsystem: Interlace
Synchronizingsystem: Internal synchronization
Dimensions(WxHxD): 23.4 x 23.4 x 26.1 mm
Weight: Approx. 23 g (without cable)
Camera Unit (CMOS-220)
Outputvideo
: Wide-angle mirror image (for rearview)
Sensor: 1/3.6-inch color CMOS sensor
Numberofpixels: Approx. 330,000 pixels
Lens
: Wide angle, Focal length f=1.12 mm, F value 2.2
Anglesofview
: Horizontal: Approx. 128°
: Vertical: Approx. 103°
Videooutput: 1.0Vp-p/ 75Ω
Illuminationrange: Approx. 0.9 to 100,000 lux
Irissystem: Electronic iris
Scanningsystem: Interlace
Synchronizingsystem: Internal synchronization
Dimensions(WxHxD): 23.4 x 23.4 x 23.9 mm
Weight: Approx. 22 g (without cable)
Switch Unit (CMOS-320 only)
Dimensions(WxHxD): 27.5 x 32.8 x 12 mm
Weight: Approx. 10 g (without cable)
General
Operatingvoltage: 14.4V (9.0 V – 16.0 V)
Max.currentconsumption(CMOS-320): 100 mA
Max.currentconsumption(CMOS-220): 50 mA
•Mirrorimagemeansthatthevideoimageinvertstheleft
andrightjustliketheimageseenontherearviewmirror
orasidemirror.
•Specificationssubjecttochangewithoutnotice.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for countries that have adopted separate waste
collection systems)
Productsandbatterieswiththesymbol(crossed-
outwheeledbin)cannotbedisposedas
householdwaste.
Oldelectricalandelectronicequipmentand
batteriesshouldberecycledatafacilitycapable
ofhandlingtheseitemsandtheirwaste
byproducts.
Contactyourlocalauthorityfordetailsin
locatingarecyclefacilitynearesttoyou.
Properrecyclingandwastedisposalwillhelp
conserveresourceswhilstpreventing
detrimentaleffectsonourhealthandthe
environment.
Notice:Thesign“Pb”belowthesymbolfor
batteriesindicatesthatthisbattery
containslead.
Specifications
LVT2720-001A.indb 15 14/02/14 15:10