Kenwood KWVXL1 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
V1.0321
KWVXL1
INSTALLATION MANUAL
This dash image is a visual representaon for display purposes only.
VAUXHALL
VIVARO (B)
2014-2018

2
www.topvehicletech.com
ABOUT THIS PRODUCT
The KWVXL1 installaon kit allows for the retenon of the vehicle’s steering wheel controls and helps maintain
the original aesthec of the interior when installing a new car stereo. The KWVXL1 gives you everything you
need for a complete install in one box. The components of this kit are compable for the Vauxhall Vivaro (B,
2014-2018) with factory stereos. The wiring harness and interface will retain the steering wheel controls.
The interface supplied features an OEM specic connector.
CUSTOMER SUPPORT
Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: [phone] E-Mail: [e-mail]
CONTENTS
• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x DAB antenna adapter
• 1x USB retenon lead
• 1x Stereo patch lead

3
www.topvehicletech.com
FITTING GUIDE
1. Using a panel removal tool remove the main fascia panel.
1. Open the passenger side door and proceed to pull away the door trim from the pillar.
STEREO REMOVAL
DAB ANTENNA INSTALLATION
2. Using a set of panel removal tools, begin to pry away the pillar casing.
4. The DAB antenna not only has a self adhesive backing, but also features a black earth sheet. When plac-
ing the DAB antenna, the earth sheet MUST be placed onto the metal part of the pillar. The antenna itself
must be located roughly 15cm from the top of the windscreen.
Note: this antenna must not be placed atop any kind of heang elements, this will interfere with the
antenna’s signal.
5. Once happy with the placement, take the 3m of wiring extension and feed it down through to the
stereo’s opening. With the wiring adjusted to the appropriate length, feel free to re-install the glovebox.
3. The glovebox will need to be dropped down to route the antennas wiring. To do this, rst open the
glovebox and unclip the glovebox side panel. You will need to remove 2x bolts atop the inside lip and 2x
underneath. Once free, simply leave in the footwell.
FASCIA PLATE SET-UP
1. Transfer any/all clips from the back of the old fascia panel to the new fascia panel.
2. Once the panel is out of the way, undo the 4x screws that hold the radio in place and remove whilst
disconnecng the wiring.
2. Aach the brackets that come with the kit to the relevant sides of the stereo. Place into the vehicle and
roughly test t with the fascia to measure whether the brackets need moving forwards/backwards.
3. When happy with the alignment of the brackets, and the “Stereo Installaon” process is complete,
screw the stereo into the dashboard ulising the pre-exisng bolts and clip on the new fascia thereaer.
1. Take the steering wheel control interface in hand and connect both the 12-way stereo patch lead and
the 14-way steering wheel harness connectors to the corresponding sides.
2. Connect the bullet connector from the stereo patch lead to the ‘steering wheel remote input’ on the
back of the new stereo.
3. Connect the antenna adapter to both the pre-exisng vehicle connecon and to the back of the new
stereo.
4. Connect the DAB antenna’s SMB connector to the back of the new stereo.
STEREO INSTALLATION
5. Connect the USB retenon lead between the original connector and the back of the new stereo.
6. When all the above wires (and any addional accessories) have been connected, nally make the
connecons between the stereo and the vehicles pre-exisng connector.

4
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
STEERING WHEEL CONTROL FUNCTIONALITY
1
2
3
4
SRC
Front
Back 4
Front
1. Volume +
2. Volume -
3. Source
Back
4. Track + / Track -
Front
1. Volume +
2. Volume -
3. Source
Back
4. Scroll
Original Buon New Funcon

5
www.topvehicletech.com
WIRING DIAGRAM
ISO Connector
Connect to new stereo
OEM Specific Connector [x2]
Connect to connector from vehicle
Stereo Patch Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first, before power
connection is made to the interface
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
Stereo Patch Lead Bullet Connector
Connect to ‘Steering Wheel Remote Input’ on back
of the stereo.

6
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone: [phone]
E-Mail: [e-mail]
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE
If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.