Kenwood TK-5720 User manual

TK-5720/ TK-5820
© B62-2206-00 (K)
09 08 07 06 05 04 03 02 01 00
VHF P25 TransceiVer/
UHF P25 TransceiVer
insTrUcTion ManUal
ÉMeTTeUr-rÉcePTeUr P25 VHF/
ÉMeTTeUr-rÉcePTeUr P25 UHF
MoDe D’eMPloi
TranscePTor P25 VHF/
TranscePTor P25 UHF
ManUal De insTrUcciones

VHF P25 TransceiVer/
UHF P25 TransceiVer
TK-5720/ TK-5820
insTrUcTion ManUal
enGlisH
Terminal Description
Microphone Jack
Pin NO. Pin Name Description Specification I/O Notes
OSOMClortnocthgilkcabyekciMCLB1
OV6.31tuptuOrewoPBS2
–dnuorGdnuorGDNG3
4 PTT/TXD PTT Input/Serial Data Output High Impedance/ CMOS I/O
–dnuorGdnuorGCIMEM5
006tupnIlangiSCIMCIM6 ΩI
7 HOOK/RXD Hook Detection/ Serial Data Input High Impedance I
O/IecnadepmIhgiHnoitceteDataDCIMMD8
ACC (D-SUB 25 Pin Connector)
Pin NO. Pin Name Description Specification I/O Notes
IelbitapmocC232-SRtupnIataDlaireS1DXR2
OelbitapmocC232-SRtuptuOataDlaireS1DXT3
ISOMCtupnIataDID5 input : 0.5 V p-p (Typ.) Data Rate : 9600 bps
High Impedance
006tupnIlangiSCIM2IM6 ΩI
–dnuorGdnuorGDNG7
OLTTtuptuOataDlaireS2DXT9
ILTTtupnIataDlaireS2DXR01
–dnuorGdnuorGDNG11
–dnuorGdnuorGDNG81
–dnuorGdnuorGCIMEM52
Antenna Connector
Impedance is 50 Ω .

Thank You
We are grateful you have chosen Kenwood for your personal mobile applications.
This instruction manual covers only the basic operations of your mobile radio. Ask your dealer for
information on any customized features that may have been added to your radio.
noTices To The user
uGovernment law prohibits the operation of unlicensed transmitters within the territories under
government control.
uIllegal operation is punishable by fine and/or imprisonment.
uRefer service to qualified technicians only.
SAFETY: It is important that the operator is aware of, and understands, hazards
common to the operation of any transceiver.
uEXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)
Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry
spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area.
uINJURY FROM RADIO FREQUENCY TRANSMISSIONS
Do not operate your transceiver when somebody is either standing near to or touching the
antenna, to avoid the possibility of radio frequency burns or related physical injury.
uDYNAMITE BLASTING CAPS
Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them
to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where
“TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps
in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not
transmit while the caps are being placed into or removed from the container.
The AMBE+2™ voice coding Technology embodied in this product is protected by intellectual
property rights including patent rights, copyrights and trade secrets of Digital Voice Systems,
Inc. This voice coding Technology is licensed solely for use within this Communications
Equipment. The user of this Technology is explicitly prohibited from attempting to extract,
remove, decompile, reverse engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in Kenwood product
memories are reserved for Kenwood Corporation.

i
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer for technical assistance.
Precautions
Observe the following precautions to prevent fire, personal injury, and transceiver
damage.
• Do not attempt to configure the transceiver while driving; it is too dangerous.
• Do not disassemble or modify the transceiver for any reason.
• Do not expose the transceiver to long periods of direct sunlight, nor place it near heating
appliances.
• If an abnormal odor or smoke is detected coming from the transceiver, switch the
transceiver power off immediately, and contact your Kenwood dealer.
• Use of the transceiver while you are driving may be against traffic laws. Please check
and observe the vehicle regulations in your area.
• Do not use options not specified by Kenwood.
◆The transceiver operates in 12 V negative ground systems only! Check the battery polarity and
voltage of the vehicle before installing the transceiver.
◆Use only a Kenwood optional DC power cable.
◆Do not cut and/or remove the fuse holder on the DC power cable.
For passenger safety, install the transceiver securely using an optional mounting bracket and screw
set so the transceiver will not break loose in the event of a collision.

ii
CONTENTS
UNPACKING AND CHECKING EQUIPMENT ........................................................ 1
Supplied AcceSSorieS ......................................................................................... 1
PREPARATION....................................................................................................... 2
ToolS required .................................................................................................. 2
power cAble connecTion.................................................................................... 2
inSTAlling The TrAnSceiver .................................................................................. 3
GETTING ACQUAINTED........................................................................................ 4
FronT pAnel ....................................................................................................... 4
diSplAy ............................................................................................................... 5
PROGRAMMABLE FUNCTIONS............................................................................ 6
BASIC OPERATIONS ............................................................................................. 7
SwiTching power on/oFF.................................................................................. 7
AdjuSTing The volume ......................................................................................... 7
SelecTing AZone And chAnnel ............................................................................ 7
TrAnSmiTTing ....................................................................................................... 7
receiving ............................................................................................................ 8
MENU MODE .......................................................................................................... 9
menu AcceSS ...................................................................................................... 9
menu conFigurATion ........................................................................................... 9
chArAcTer enTry.............................................................................................. 11
ScAn ................................................................................................................... 12
TemporAry chAnnel lockouT ............................................................................ 12
ScAn deleTe/Add .............................................................................................. 12
prioriTy ScAn ................................................................................................... 12
prioriTy-chAnnel SelecT .................................................................................. 13
ScAn reverT..................................................................................................... 13
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION................................. 14
SelcAll (SelecTive cAlling) .............................................................................. 14
STATuS meSSAge................................................................................................ 14
ShorT/long meSSAgeS ...................................................................................... 15
gpS reporT..................................................................................................... 15
ADVANCED OPERATION .................................................................................... 16
dTmF (duAl Tone mulTi Frequency) cAllS ...................................................... 16
encyrpTion ....................................................................................................... 16
emergency cAllS.............................................................................................. 17
SignAling .......................................................................................................... 17
lcd brighTneSS ............................................................................................... 18
horn AlerT....................................................................................................... 18
public AddreSS (pA)......................................................................................... 18
clock ............................................................................................................... 19
BACKGROUND OPERATIONS ............................................................................ 20
Time-ouT Timer (ToT) ....................................................................................... 20
SignAl STrengTh indicATor................................................................................ 20
compAnder ....................................................................................................... 20
buSy chAnnel lockouT (bcl)........................................................................... 20
pTT id ............................................................................................................. 20
VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT......................................... 21
voice recorder................................................................................................ 21
voice guide ...................................................................................................... 22

1
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking instructions are for use by your Kenwood dealer, an authorized
Kenwood service facility, or the factory.
Carefully unpack the transceiver. We recommend that you identify the items listed in
the following list before discarding the packing material. If any items are missing or
have been damaged during shipment, file a claim with the carrier immediately.
Supplied AcceSSorieS
Microphone(withcable).............................................1
Microphone hanger (with 4 x 16 mm self-tapping screws) ...................1
DCpowercable...................................................1
• Fuse (15 A) ....................................................2
Mountingbracket..................................................1
Screw set
• 5 x 16 mm self-tapping screw ......................................4
• Hex-headed screw with washer ....................................4
• Spring washer ..................................................4
• Flat washer ....................................................4
Instructionmanual .................................................1

2
Various electronic equipment in your vehicle may malfunction if they are not properly protected
from the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-
skid braking, and cruise control systems are typical examples of equipment that may malfunction.
If your vehicle contains such equipment, consult the dealer for the make of vehicle and enlist
his/her aid in determining if they will perform normally while transmitting.
Note: The following preparation instructions are for use by your Kenwood dealer, an authorized
Kenwood service facility, or the factory.
ToolS required
Note: Before installing the transceiver, always check how far the mounting screws will extend
below the mounting surface. When drilling mounting holes, be careful not to damage vehicle wiring
or parts.
The following tools are required for installing the transceiver:
• 1/4 inch (6 mm) or larger electric drill
• 5/32 inch (4.2 mm) drill bit for the self-tapping screws used to mount the optional
mounting bracket
• Circle cutters
power cAble connecTion
◆The transceiver operates in 12 V negative ground systems only! Check the battery polarity and
voltage of the vehicle before installing the transceiver.
◆Use only a Kenwood optional DC power cable.
◆Do not cut and/or remove the fuse holder on the DC power cable.
1Check for an existing hole, conveniently located in the firewall, where a power
cable can be passed through. If no hole exists, use a circle cutter to drill the
firewall, then install a rubber grommet.
2Run the two power cable leads through the firewall and into the engine
compartment, from the passenger compartment.
3Connect the red lead to the positive (+) battery terminal and the black lead to
the negative (–) battery terminal.
• Locate the fuse as close to the battery as possible.
4Coil and secure the surplus cable with a retaining band.
• Be sure to leave enough slack in the cables so the transceiver can be removed for
servicing while keeping the power applied.
PREPARATION

3
inSTAlling The TrAnSceiver
For passenger safety, install the transceiver securely using an optional mounting bracket and screw
set so the transceiver will not break loose in the event of a collision.
1Mark the position of the holes in the dash by using the mounting bracket as a
template. Drill the holes, then attach the mounting bracket using self-tapping
screws.
• Be sure to mount the transceiver in a location where the controls are within easy
reach of the user and where there is sufficient space at the rear of the transceiver for
cable connections.
2Connect the antenna and power cable to the transceiver.
3Slide the transceiver into the mounting bracket and secure it using
hex-headed screws.
4Mount a microphone hanger in a location where it will be within easy reach of
the user.
• The microphone and microphone cable should be mounted in a location where it will
not interfere with the safe operation of the vehicle.
When replacing the fuse in the DC power cable, be sure to replace it with a fuse of the same value.
Never replace a fuse with a fuse that has a higher value.
Hex-headed
screws
DC power
cable
Mounting
bracket
Antenna
connector
Power input
connector
Fuse
Black (–) cable
Red (+) cable
12 V vehicle
battery
Microphone
Ignition
sense cable
Flat washer
Spring washer
Self-tapping screw
External
speaker jack

4
GETTING ACQUAINTED
FronT pAnel
①(power) switch
Press and hold for approximately 1 second to switch the transceiver power ON
and OFF.
②key
Press to activate its programmable function {page 6}.
③key
Press to activate its programmable function {page 6}.
④key
Press to activate its programmable function {page 6}. Acts as an Up key for
certain functions.
⑤key
Press to activate its programmable function {page 6}. Acts as a Down key for
certain functions.
⑥Microphone jack
Insert the microphone plug into this jack.
⑦LED indicator
If enabled by your dealer, lights red while transmitting, green while receiving
a call, and orange when receiving an optional signaling call (2-tone, DTMF
signaling, etc.).
⑧key
Press to activate its programmable function {page 6}.
⑨key
Press to activate its programmable function {page 6}.
⑩key
Press to activate its programmable function {page 6}.
⑪key
Press to activate its programmable function {page 6}.
:
B> 2 8    
@ . =;



5
⑫key
Press to activate its programmable function {page 6}.
⑬key
Press to activate its programmable function {page 6}.
⑭Speaker
Internal speaker
⑮PTT (Push-to-Talk) switch
Press and hold this switch then, speak into the microphone to call a station.
diSplAy
Indicator Description
Monitor or Squelch Off is activated.
Blinks when an incoming call matches your Optional
Signaling.
The current zone (left icon) or channel (right icon) is added to
scan.
Scan is in progress. Blinks while scan is paused.
A message is stored in memory. Blinks when a new
message has arrived.
The current channel is a Priority channel.
Operator Selectable Tone (OST) is activated.
Talk Around is activated.
Signal Strength indicator {page 20}
Encryption is activated.
Auto Recording on the VGS-1 option is activated.
Auto Reply Message on the VGS-1 option is activated.
The auxiliary A function is activated.
The auxiliary B function is activated.
Lone Worker is activated.

6
PROGRAMMABLE FUNCTIONS
Following is a list of available programmable functions. Please contact your
dealer for further details on those functions which have been programmed on your
transceiver.
• None (No function)
• 2-tone 1
• Auto Reply Message 1, 2
• Autodial 1
• Autodial Programming 1
• AUX A
• AUX B
• Call 1 ~ 6
• Channel Down
• Channel Entry
• Channel Recall
• Channel Up
• Clock
• Clock Adjustment
• Direct Channel 1 ~ 5
• Direct Channel Select 1 ~ 5
• Display Format
• Emergency 3
• Encryption 4
• Encryption Code 4
• Fixed Volume
• Function
• GPS Position Display
• Home Channel
• Home Channel Select
• Horn Alert
• Individual 4
• Key Delete
• LCD Brightness
• Lone Worker
• Maintenance
• Menu
• Monitor
• Monitor Momentary
• Operator Selectable Tone 1
• Playback 2
• Priority-channel Select
• Public Address
• Scan
• Scan Delete/Add
• Selcall 1
• Selcall + Status 1
• Selcall + Short Message 1
• Send the GPS data 1
• Squelch Level 1
• Squelch Off 1
• Squelch Off Momentary 1
• Stack
• Status 1
• Short Message 1
• Talk Around
• Talkgroup 4
• Talkgroup Reset 4
• Transceiver Password
• Voice Memo 2
• Volume Down
• Volume Up
• Zeroize 4, 5
• Zone Delete/Add
• Zone Down
• Zone Up
1Available only for analog operation.
2Available only if the VGS-1 optional board has been installed.
3Can be programmed only on the key and an optional auxiliary switch, such as an emergency
foot switch.
4Available only for P25 operation.
5Available only if the Secure Cryptographic Module (SCM) optional board has been installed.

7
BASIC OPERATIONS
SwiTching power on/oFF
Press and hold for approximately 1 second to turn the transceiver power ON.
Press and hold again to turn the transceiver OFF.
■Transceiver Password
If the transceiver is password protected, “PASSWORD” will appear on the
display when the power is turned ON. To unlock the transceiver, enter the
password:
1Select a character using / .
• If you are using a microphone keypad, you can enter the password by direclty.
2Press to enter the selected character.
• This step is unnecessary when using the keypad.
3Repeat steps 1 and 2 to enter the entire password.
• Press or #to delete a character. Press and hold or #to delete all
characters.
4Press or to confirm the entry.
• If you enter an incorrect password, an error tone sounds and the transceiver
remains locked.
• The password can contain a maximum of 6 digits.
AdjuSTing The volume
Press the keys programmed as Volume Up/Volume Down to adjust the volume
level.
SelecTing AZone And chAnnel
Select the desired zone using the keys programmed as Zone Up/ Zone Down.
Each zone contains a group of channels.
Select the desired channel using the keys programmed as Channel Up/
Channel Down. Each channel is programmed with settings for transmitting and
receiving.
• You can toggle the display between the zone and channel names and numbers by
pressing the key programmed as Display Format, or by accessing the Menu {page 9}.
TrAnSmiTTing
1Select the desired zone and channel.
2Press the key programmed as Monitor or Squelch Off to check whether or
not the channel is free.
• If the channel is busy, wait until it becomes free.

8
3Press the microphone PTT switch and speak into the microphone. Release
the PTT switch to receive.
• For best sound quality, hold the microphone approximately 1.5 inches (3 ~ 4 cm)
from your mouth.
■Making Group Calls (P25)
Channels programmed for P25 operation already have a Talkgroup ID
assigned. For these channels, simply press and hold the microphone PTT
switch to make the call. Otherwise, if a key has been programmed with
Talkgroup, you can select a group ID to make a call to those parties.
1Press the key programmed as Talkgroup.
2Press / to select a group ID/name.
3Press or to set the selected Talkgroup.
4Press and hold the microphone PTT switch to make the call.
•Speak into the microphone as you would during a normal transmission.
■Making Individual Calls (P25)
If a key has been programmed with Individual, you can make calls to specific
persons.
1Press the key programmed as Individual.
2Press / to select a unit ID/name.
• If you are using a microphone keypad, you can enter a unit ID directly.
3Press and hold the microphone PTT switch to make the call.
•Speak into the microphone as you would during a normal transmission.
receiving
Select the desired zone and channel. If signaling has been programmed on the
selected channel, you will hear a call only if the received signal matches your
transceiver settings.
Note: Signaling allows your transceiver to code your calls. This will prevent you from listening to
unwanted calls. Refer to “SIGNALING” on page 17 for details.
■Receiving Group Calls (P25)
When you receive a group call with a group ID that matches the ID set up on
your transceiver, and the Network Access Code also matches, you can hear the
caller’s voice.
■Receiving Individual Calls (P25)
When you receive an individual call, a ringing tone will sound. If the Network
Access Code matches and the squelch type is set to Selective call, the caller’s
ID will also appear on the display.
To respond to the call, press and hold the microphone PTT switch and speak
into the transceiver as you would during a normal transmission.

9
Many functions on this transceiver are selected or configured through the Menu
instead of physical controls. Once you become familiar with the Menu system,
you will appreciate the versatility it offers.
menu AcceSS
1Press the key programmed as Menu.
• The category list is shown.
• When there is only 1 category, the function list is shown (proceed to step 4).
2Press / to select a category item.
• If you are using a microphone keypad, you can enter a category number directly.
3Press or to view the function list.
4Press / to select a function item.
• If you are using a microphone keypad, you can enter a function number directly.
5Press or to set up the selected function item.
• Press or # to return to the category list.
6Press / to select your desired setting.
• For settings with more than 1 level, repeat steps 5 and 6.
7Press or to set the selected setting and exit Menu mode.
• Press or #at any time to return to the previous display.
• Press at any time to exit Menu mode.
menu conFigurATion
Some transceiver keys may already be programmed with functions listed in the
Menu. Those functions can be accessed directly by pressing the key. All other
functions can still be accessed using the transceiver Menu. The following table
lists the available Menu items.
Display Description
2-TONE 2-tone Mode
AUTO REPLY MSG Auto Reply Message ON/OFF
AUTO DIAL Autodial Mode
AUTO DIAL PROG Autodial Programming Mode
AUX A AUX A ON/OFF
AUX B AUX B ON/OFF
CLOCK Clock ON/OFF
CLOCK ADJUST Clock Adjustment mode
MENU MODE

10
Display Description
DIRECT CH1 SEL ~
DIRECT CH5 SEL Direct channel 1 ~ 5 Select
DISP FORMAT Display Format ON/OFF
ENCRYPTION Encryption ON/OFF
ENCRYP CODE Encryption Code mode
FIXED VOLUME Fixed Volume
GPS POS DISP GPS Position Display mode
HOME CH SEL Home Channel Select
HORN ALERT Horn Alert ON/OFF
INDIVIDUAL Individual mode
KEY DELETE Encryption Key Delete mode
LCD BRIGHTNESS LCD Brightness level
MONITOR Monitor ON/OFF
OST OST ON/OFF
OST LIST OST mode
PLAYBACK Playback mode
PRI CH SEL Priority Channel Select mode
PUBLIC ADDRESS Public Address System ON/OFF
SCAN Scan ON/OFF
SCAN DEL/ADD Scan Delete/Add
SELCALL Selcall mode
SELCALL+STATUS Selcall + Status mode
SELCALL+SDM Selcall + SDM mode
SEND GPS DATA Transmit your GPS data
SHORT MESSAGE Short Message mode
SQUELCH LEVEL Squelch Level mode
SQUELCH OFF Squelch Off ON/OFF
STACK Stack mode
STATUS Status mode
TALK AROUND Talk Around ON/OFF
TALKGROUP Talkgroup mode
TALKGROUP RST Talkgroup Reset
PASSWORD Transceiver Password mode
VOICE MEMO Voice Memo mode

11
Display Description
ZEROIZE Zeroize
ZONE DEL/ADD Zone Delete/Add
chArAcTer enTry
There are 2 methods available for entering characters:
1) / keys
Press / to cycle through the chracters A ~ Z, 0 ~ 9 and a space (default
settings).
You can also assign a character to an optional key and later press that key to
recall the assigned character: A ~ Z, a ~ z, 0 ~ 9, or a space and characters.
2) Microphone keypad
Press the microphone keypad keys to enter characters as shown in the table
below:
DTMF Key Character Cycle
1 1
2 A B C a b c 2
3 D E F d e f 3
4 G H I g h i 4
5 J K L j k l 5
6 M N O m n o 6
7 P Q R S p q r s 7
8 T U V t u v 8
9 W X Y Z w x y z 9
0 [space] 0

12
SCAN
Scan monitors for signals on the transceiver channels. While scanning, the
transceiver checks for a signal on each channel and only stops if a signal is
present.
To begin scanning, press the key programmed as Scan.
• The icon appears on the display.
• When a signal is detected on a channel, Scan pauses at that channel. The transceiver
will remain on the busy channel until the signal is no longer present, at which time Scan
resumes.
To stop scanning, press the Scan key again.
Note: To use Scan, there must be at least 2 channels in the scan sequence.
TemporAry chAnnel lockouT
During scan, you can temporarily remove specific channels from the scanning
sequence by selecting them and pressing the key programmed as Scan Delete/
Add.
• The channel is no longer scanned. However, when scanning is ended and restarted, the
channels are reset and deleted channels will again be in the scanning sequence.
ScAn deleTe/Add
You can add and remove zones and/or channels to and from scan.
1Select your desired zone and/or channel.
2Press the key programmed as Zone Delete/Add (to add/remove zones) or
Scan Delete/Add (to add/remove channels).
• You can also press and hold the key programmed as Scan Delete/Add to add/
remove zones.
prioriTy ScAn
Note: To use Priority Scan, a Priority channel must be programmed.
When using a single Priority channel, the transceiver will automatically change to
the Priority channel when a call is received on that channel, even if a call is being
received on a normal channel.
When using dual Priority channels, Priority channel 1 is given precedence over
Priority channel 2. So, if a call is received on Priority channel 1 while a call is
already on Priority channel 2, the transceiver will change to Priority channel 1.

13
prioriTy-chAnnel SelecT
If the Priority channel has been set as Operator Selectable by your dealer, you
can reprogram the Priority channels.
1Select your desired zone and channel.
2Press the key programmed as Priority-channel Select.
3Press / to select “NORMAL”, “PRIORITY 1” ( ), “PRIORITY 2” ( ), or
“PRIORITY 1&2” ( ).
4Press to save the setting.
ScAn reverT
The Scan Revert channel is the channel selected when you press the microphone
PTT switch to transmit during scan. Your dealer can program one of the following
types of Scan Revert channels:
• Selected: The last channel selected before scan.
• Selected + Talkback: Same as “Selected”, plus you can respond to calls on
the channel at which scan is paused.
• Priority 1/ Priority 2: The Priority channel (either Priority 1 or Priority 2).
• Priority 1 + Talkback/ Priority2 + Talkback: Same as “Priority 1/ Priority 2”,
plus you can respond to calls on the channel at which scan is paused.
• Last Called + Selected: Same as “Selected + Talkback”, plus you can
respond on the last channel on which you received a call after scan has
resumed.

14
FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by
Kenwood Corporation.
Note: This function is available only in analog operation.
SelcAll (SelecTive cAlling)
A Selcall is a voice call to a station or group of stations.
■Transmitting
1Select your desired zone and channel.
2Press the key programmed as Selcall or Selcall + Status to enter Selcall
mode.
3Press / to select the station you want to call.
• If Manual Dialing is enabled, you can directly enter the station ID using the
microphone keypad.
4Press the microphone PTT switch and begin your conversation.
■Receiving
An alert tone will sound and the transceiver will automatically enter Selcall
mode. The calling station’s ID will appear when a Selcall is received. You can
respond to the call by pressing the microphone PTT switch and speaking into
the microphone.
■Identification Codes
An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number.
Each transceiver has its own ID.
• Enter a Fleet number (100 ~ 349) to make a group call.
• Enter an ID number (1000 ~ 4999) to make an individual call in your fleet.
• Enter a Fleet number and select “ALL” ID to make a call to all units in the selected
fleet (Fleet call).
• Select “ALL” Fleet and enter an ID number to make a call to the selected ID in all
fleets (Supervisor call).
• Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call).
STATuS meSSAge
You can send and receive 2-digit Status messages which may be decided in your
talk group. Messages can contain up to 16 alphanumeric characters. Status
messages range from 10 to 99 (80 ~ 99 are reserved for special messages).
A maximum of 15 received messages (combined status messages and short
messages) can be stored in the stack memory of your transceiver.
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION

15
■Transmitting
1Select your desired zone and channel.
2Press the key programmed as Status to enter Status mode (proceed to
step 5) or Selcall + Status to enter Selcall mode (proceed to step 3).
3Press / to select the station you want to call.
• If Manual Dialing is enabled, you can enter a station ID by using the microphone
keypad.
4Press to enter Status mode.
5Press / to select the status you want to transmit.
• If Manual Dialing is enabled, you can enter a status ID by using the microphone
keypad.
6Press the microphone PTT switch or to initiate the call.
• “<<COMPLETE>>” appears on the display when the status has been
successfully transmitted.
■Receiving
The icon will flash and a calling ID or text message will appear when a
Status call is received. Press any key to return to normal operation.
■Reviewing Messages in the Stack Memory
1Press the key programmed as Stack, or press and hold the key
programmed as Selcall, Status, or Selcall + Status to enter Stack mode.
• The last received message is displayed.
2Press / to select the desired message.
• Message types are identified as follows:
I: Caller ID, S: Status Message, M: Short Message
• Press and hold for 1 second to cycle the display information as follows:
ID Name > Status/Short Message > Channel > Time Stamp
3 Press to return to normal operation.
• To delete the selected message, press or #. To confirm the deletion, press
or .
• To delete all messages, press and hold or #for 1 second. To confirm the
deletion, press or .
ShorT/long meSSAgeS
Received short messages are displayed the same as Status messages and are
stored in the same stack memory.
To send short messages, and to send and receive long messages, you must
connect the transceiver to a PC. Ask your dealer for details.
gpS reporT
To send your location data, you must first connect a GPS unit to the transceiver.
Once connected, press the key programmed as Send the GPS data, or access the
Menu {page 9}. If set up by your dealer, GPS data may be automatically transmitted
at a preset time interval.