KERN KBP V20 User manual

KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: [email protected]
Phone: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Installation Instructions
Platform
KERN KBP V20
Type TKBP-V20-A
Version 1.0
2023-09
GB
TKBP-V20-A-IA-e-2310

2 TKBP-V20-A-IA-e-2310
GB
KERN KBP V20
Platform
Version 1.0 2023-09
Installation Instructions
Contents
1General hints.................................................................................................. 3
2Technical data................................................................................................ 3
2.1 Technical data of the weighing cell........................................................................................ 4
3Basic Information (General).......................................................................... 5
3.1 Documentation ......................................................................................................................... 5
3.2 Proper use................................................................................................................................. 5
3.3 Improper Use ............................................................................................................................ 5
3.4 Warranty.................................................................................................................................... 5
3.5 Monitoring of Test Resources................................................................................................. 5
4Basic Safety Precautions.............................................................................. 6
4.1 Pay attention to the instructions in the Operation Manual .................................................. 6
4.2 Personnel training.................................................................................................................... 6
5Transport and storage................................................................................... 6
5.1 Testing upon acceptance ........................................................................................................ 6
5.2 Packaging / return transport ................................................................................................... 6
6Unpacking, Installation and Commissioning............................................... 7
6.1 Installation Site, Location of Use............................................................................................ 7
6.2 Unpacking, Scope of delivery ................................................................................................. 8
6.3 Placing....................................................................................................................................... 8
6.3.1 Transport Securing..................................................................................................................... 9
6.4 Levelling.................................................................................................................................. 10
6.5 Connecting a display unit...................................................................................................... 10
7Operation...................................................................................................... 10
8Operation limits............................................................................................ 11
9Servicing, maintenance, disposal .............................................................. 12
9.1 Cleaning .................................................................................................................................. 12
9.2 Servicing, maintenance ......................................................................................................... 12
9.3 Disposal................................................................................................................................... 12
10 Instant help for troubleshooting................................................................. 13
11 Preload, Deadload and Overload settings................................................. 14
12 Enclosure ..................................................................................................... 16

TKBP-V20-A-IA-e-2310 3
1 General hints
These installation instructions contain all data necessary for placing and
commissioning the following platforms:
KERN TKBP 6V20LM-A
KERN TKBP 15V20M-A, TKBP 15V20LM-A
KERN TKBP 30V20M-A
KERN TKBP 60V20M-A, TKBP 60V20LM-A
KERN TKBP 150V20M-A, TKBP 150V20LM-A
KERN TKBP 300V20M-A
KERN TKBP 600V20M-A
2 Technical data
Item no./ Type
Weighin
g range
Max
Readabi
lity
d
Verificati
on value
e
Minimum
load
Min
Cable
length
appro
x.
Transport
Securing
kg
g
g
g
m
TKBP 6V20LM-A
3 / 6
0,1 / 0,2
1 / 2
20 / 40
3
yes
TKBP 15V20M-A
6 / 15
0,2 / 0,5
2 / 5
40 / 100
3
yes
TKBP 15V20LM-A
6 / 15
0,2 / 0,5
2 / 5
40 / 100
3
yes
TKBP 30V20M-A
15 / 30
0,5 / 1
5 / 10
100 / 200
3
yes
TKBP 60V20M-A
30 / 60
1 / 2
10 / 20
200 / 400
3
yes
TKBP 60V20LM-A
30 / 60
1 / 2
10 / 20
200 / 1000
3
yes
TKBP 150V20M-A
60 / 150
2 / 5
20 / 50
400 / 1000
3
no
TKBP 150V20LM-A
60 / 150
2 / 5
20 / 50
400 / 1000
3
no
TKBP 300V20M-A
150 / 300
5 / 10
50 / 100
1000 / 2000
3
no
TKBP 600V20M-A
300 / 600
10 / 20
100 / 200
2000 / 4000
3
no

4 TKBP-V20-A-IA-e-2310
2.1 Technical data of the weighing cell
Sensitivity
2 mV/V
Input resistance (all TKBP models*)
406 Ω ± 6 Ω
*excepted
TKBP 6V20LM-A
TKBP 15V20M-A
TKBP 15V20LM-A
409 Ω ± 6 Ω
Output resistance
350 Ω ± 3 Ω
Power supply
5 –12 V AC/DC
Accuracy class
C3

TKBP-V20-A-IA-e-2310 5
3 Basic Information (General)
3.1 Documentation
These installation instructions contain all data necessary for placing and
commissioning the platform KERN TKBP V20-A.
In combination with a display unit, described below as weighing system, for operation
configuration, please refer to the operating instructions of the display unit.
3.2 Proper use
The platform purchased by you is intended to define the weighing value of weighed
goods. It is intended to be used as a “non-automatic balance”, i.e. the material to be
weighed is manually and carefully placed in the centre of the weighing pan. As soon
as a stable weighing value is reached, the weighing value can be read.
3.3 Improper Use
•Our balances are non-automatic balances, not provided for the use in dynamic
weighing processes. However, the balances can also be used for dynamic weighing
processes after verifying their individual operative range, and here especially the
accuracy requirements of the application.
•Do not leave permanent load on the weighing pan. This can damage the measuring
mechanism.
•Impacts and overloading exceeding the stated maximum load (max) of the weighing
system, minus a possibly existing tare load, must be strictly avoided. The weighing
system could be damaged.
•Never operate the weighing system in explosive environment. The serial version is
not explosion protected.
•Changes to the weighing system's design are not permitted. This may lead to
incorrect weighing results, safety-related faults and destruction of the balance.
•The weighing system unit may only be operated in accordance with the described
default settings. Other areas of use must be released by KERN in writing.
3.4 Warranty
Warranty claims shall be voided in case:
•Our conditions in the operation manual are ignored
•The appliance is used beyond the described intended use
•Structural changes of the device
•Mechanical damage and damage caused by media, liquids
•Natural wear and tear
•The appliance is improperly set up or incorrectly electrically connected
•Overload of the measuring system
3.5 Monitoring of Test Resources
In the framework of quality assurance the measuring-related properties of the weighing
system and, if applicable, the testing weight, must be checked regularly. The
responsible user must define a suitable interval as well as type and scope of this test.

6 TKBP-V20-A-IA-e-2310
Information is available on KERN’s home page (www.kern-sohn.com with regard to the
monitoring of weighing system test substances and the test weights required for this.
In KERN's accredited DKD calibration laboratory test weights and weighing systems
may be calibrated (return to the national standard) fast and at moderate cost.
4 Basic Safety Precautions
4.1 Pay attention to the instructions in the Operation Manual
Carefully read this operation manual before setup and
commissioning, even if you are already familiar with KERN
balances.
4.2 Personnel training
The appliance may only be operated and maintained by trained staff.
The installation and maintenance must only be carried out by a well acquainted
specialist with the workings of weighing balances.
5 Transport and storage
5.1 Testing upon acceptance
When receiving the appliance, please check packaging immediately, and the appliance
itself when unpacking for possible visible damage.
5.2 Packaging / return transport
Keep all parts of the original packaging for a possibly required
return.
Only use original packaging for returning.
Prior to dispatch disconnect all cables and remove loose/mobile
parts.
Reattach possibly supplied transport securing devices.
Secure all parts against shifting and damage.

TKBP-V20-A-IA-e-2310 7
6 Unpacking, Installation and Commissioning
6.1 Installation Site, Location of Use
The platforms are designed in a way that reliable weighing results are achieved in
common conditions of use.
You will work accurately and fast if you select the right location for your weighing
system.
On the installation site observe the following:
•Place the weighing system on a firm, level surface. The floor must be able to
carry safely the weight of the maximally loaded platform at the resting points. At
the same time it should be sufficiently stable, that no vibrations may occur during
weighing work. This is to be considered too when the platform is installed in
conveyor systems and similar.
•In the installation site possibly no vibrations, e.g. by neighbouring machines
should occur.
•Do not use the weighing system in an explosive environment.
•Avoid extreme heat as well as temperature fluctuation e.g. caused by installing
next to a radiator or in the direct sunlight.
•Protect the weighing system against direct draughts e.g. due to open windows
and doors.
•Use weighing system only in dry environment, protect it against high humidity,
vapours and dust.
•The platform must have been stabilized to room temperature, before power
supply is switched on.
•Do not expose the appliance to heavy moisture over a longer time period. Non-
permitted condensation (condensation of air humidity on the appliance) may
occur if a cold appliance is taken to a considerably warmer environment. In this
case, acclimatize the disconnected appliance for ca. 2 hours at room
temperature.
•Avoid jarring during weighing.
•Avoid static charge of weighed goods and weighing container.
•Keep away chemicals (such as liquids or gasses), which could attack and
damage the balance inside or from outside.
•Keep IP protection of the device.
•If electromagnetic fields (e.g. by mobile phones or radio equipment), static
charges (e.g. when weighing or countings plastic parts), as well as instable
current supply occur, the displayed indications may differ considerably (wrong
weighing results, damage to the balance). Change location or remove source of
interference.

8 TKBP-V20-A-IA-e-2310
6.2 Unpacking, Scope of delivery
Remove the underconstruction and the weighing plate from the package, remove
packaging material and place the devices at the planned workplace. Check if all parts
of the scope of delivery are present and free of damage.
Scope of delivery:
•Underconstruction (lacquered steel)
•Weighing pan (stainless steel)
•Transport securing (depending on model, see chap. 2)
•Installation Instructions
6.3 Placing
1. Remove transport securing (see chap. 6.3.1).
2. Put the weighing plate on the underconstruction.

TKBP-V20-A-IA-e-2310 9
6.3.1 Transport Securing
General hints for transport securing
•Please consult the Technical Data whether your balance is equipped
with a transport securing, chap. 2.
•Do not remove the off-centre load attachments (1) as otherwise the
balance could be damaged. The off-centre load attachments are
located between the upper and the lower part of the platform. They
consist of a screw and a nut.
Note on transport securing
Type of transport securing
•4 x rubber plate in the corners
1. Remove the weighing plate.
2. Remove the transport securings.

10 TKBP-V20-A-IA-e-2310
6.4 Levelling
Accurate weighing results require a platform with perfect horizontal alignment. During
initial installation and after each change of work area it is necessary to level the
platform.
As the air bubble is located under the weighing plate,
remove it.
Align the platform with the adjustment feet until the
air bubble of the water balance is in the prescribed
circle.
6.5 Connecting a display unit
Before any installation work, disconnect the appliance from the operating
voltage.
Put the connecting cable to the display unit in a manner that it is protected
against damage.
Connect the platform to the display unit according to the following table.
Output load cell
ConnectionofplatformKERNKBP
EXC+ (5V)
see labelling of load cell
EXC- (0)
SIG-
SIG+
SEN+
SEN-
7 Operation
Information about
•Mains connection
(power is supplied via the connecting cable of the display unit)
•Initial Commissioning
•Connection of peripheral appliances
•Adjustment, linearization and verification
(only the complete balance is verifiable, i.e. platform in conjunction with a
suitable display unit)
and the correct operation you will find in the operating instructions included in the scope
of delivery of the display unit.

TKBP-V20-A-IA-e-2310 11
8 Operation limits
The platform is designed so robust thata casual excess of the maximum weighing load
will not cause any damage.
The static carrying capacity, i.e. the maximum admitted load depends on the type of
load carrier (Position A –C). The maximum static carrying capacity must not be
exceeded.
A= with centrical load
B= with side load
C= with one-side load
Avoid falling load, shock loads and impacts from
the side!
Observe the following operation limits:
Item no./ Type
A
B
C
TKBP 6V20LM-A
9 kg
6 kg
3 kg
TKBP 15V20M-A
22 kg
15 kg
7 kg
TKBP 15V20LM-A
22 kg
15 kg
7 kg
TKBP 30V20M-A
45 kg
30 kg
15 kg
TKBP 60V20M-A
90 kg
60 kg
30 kg
TKBP 60V20LM-A
90 kg
60 kg
30 kg
TKBP 150V20M-A
225 kg
150 kg
75 kg
TKBP 150V20LM-A
225 kg
150 kg
75 kg
TKBP 300V20M-A
450 kg
300 kg
150 kg
TKBP 600V20M-A
900 kg
600 kg
300 kg

12 TKBP-V20-A-IA-e-2310
9 Servicing, maintenance, disposal
Before any maintenance, cleaning and repair work disconnect the
appliance from the operating voltage.
9.1 Cleaning
Clean the platform with a soft cloth soaked with a mild cleaning agent.
Remove the weighing plate and wipe-off the dirt and the foreign bodies under it.
Do not use hard or sharp objects for this.
Remove regularly corrosive substances.
Keep IP protection.
9.2 Servicing, maintenance
The appliance may only be opened by trained service technicians who are
authorized by KERN.
Ensure that the weighing system is regularly calibrated, see chap. 3.5 Testing
instruments monitoring.
9.3 Disposal
Disposal of packaging and appliance must be carried out by operator according
to valid national or regional law of the location where the appliance is used.

TKBP-V20-A-IA-e-2310 13
10 Instant help for troubleshooting
In case of an error in the program process, briefly turn off the balance and disconnect
from power supply. The weighing process must then be restarted from the beginning.
Help:
Fault
Possible cause
The displayed weight is permanently
changing
•Draught/air movement
•Floor vibrations
•The platform has contact with foreign
objects.
•Electromagnetic fields / static charging
(choose different location/switch off
interfering device if possible)
The weighing result is obviously
wrong
•No zero display with unloaded balance
•Adjustment is no longer correct.
•Great fluctuations in temperature.
•Platform on an uneven surface.
•Electromagnetic fields / static charging
(choose different location/switch off
interfering device if possible)
Should other error messages occur, switch balance off and then on again. If the error
message remains inform manufacturer.

14 TKBP-V20-A-IA-e-2310
11 Preload, Deadload and Overload settings
Item no./ Type
Deadload** (kg)
**= already applied
preload
Centric overload
protection (kg)
Off-centre overload
protection (kg)
Minimum capactiy of the
load cell Emin (kg)
Maximum capacity of
the load cell Emax (kg)
TKBP 6V20LM-A
3,06
7,5
4,8
0
10
TKBP 15V20M-A
2,36
18,75
12
0
20
TKBP 15V20LM-A
3,68
18,75
12
0
20
TKBP 30V20M-A
3,85
37,5
24
0
50
TKBP 60V20M-A
3,85
75
48
0
100
TKBP 60V20LM-A
6,5
75
48
0
100
TKBP 150V20M-A
6,5
187,5
120
0
200
TKBP 150V20LM-A
15,84
187,5
120
0
200
TKBP 300V20M-A
15,84
375
240
0
350
TKBP 600V20M-A
21,5
750
480
0
750

15 TKBP-V20-A-IA-e-2310
Item no./ Type
Dimensions of
the platform
(mm)
Load cell type
Test certificte no.
Accur
acy
class
Ratio of min.
load cell
verification
interval
Maximum admitted
number of interval
sizes
Allowable
temperature
range
Ratio of min.
dead load output
return
Error
percentage
Y
nLC/nmax
Tmin
Tmax
Z
PLC
( °C)
( °C)
TKBP 6V20LM-A
300 x 300 x 121
L6D-10KG
TC7868 rev. 1
C3
10000
3000
-10
40
3000
0,7
TKBP 15V20M-A
300 x 240 x 121
L6D-20KG
C3
10000
3000
-10
40
3000
0,7
TKBP 15V20LM-A
400 x 300 x 112
L6D-20KG
C3
10000
3000
-10
40
3000
0,7
TKBP 30V20M-A
400 x 300 x 120
L6E-50KG
TC7838 rev. 1
C3
10000
3000
-10
40
4200
0,7
TKBP 60V20M-A
400 x 300 x 120
L6E-100KG
C3
10000
3000
-10
40
4200
0,7
TKBP 60V20LM-A
500 x 400 x 125
L6E-100KG
C3
10000
3000
-10
40
4200
0,7
TKBP 150V20M-A
500 x 400 x 125
L6E-200KG
C3
10000
3000
-10
40
3300
0,7
TKBP 150V20LM-A
650 x 500 x 149
L6E3-200KG
TC7836 rev. 1
C3
10000
3000
-10
40
6000
0,7
TKBP 300V20M-A
650 x 500 x 149
L6E3-350KG
C3
10000
3000
-10
40
6000
0,7
TKBP 600V20M-A
800 x 600 x 155
L6G-750KG
TC11191 rev. 1
C3
11000
4000
-10
40
10000
0,7

16 TKBP-V20-A-IA-e-2310
12 Enclosure

012345673ÿ9623
10343ÿ373
37ÿÿÿÿÿÿÿÿÿÿÿÿÿ5623
4ÿ5623ÿ4137016
456
7373
5413
960
4316
163433740165035413
0023
132ÿ61540ÿ61
5034526
7523
5


2ÿ !
"#"
"#"
$
"
$
%&
&
$
%"%'()*%%
+&
"+"
"&
"%&
,&-
%"
#+
""
,#++
,#+%
0.ÿ$"2'5
"%#&"%
/0123ÿ 4/5 34!/0 !)!64ÿ 7/628
0/)2 70/!ÿ7/0!4!602
#ÿ*
9:;<=:ÿ?@:ÿABCC:AÿDA<;
?@:ÿE<AF:AGÿC:D<A:ÿBG:
H
%. 43456ÿ41ÿ"%#&"%I435 JK%JK"" 956
956
256
26 68L628ÿ7)!M !)62 ÿ !N
)!O0/( !P40)!3N
((
.
053/ÿ40)!ÿQ7)2!02ÿ##&Q

01234
05334
121
671
83
13
65
13
69
83
9
19
11
ÿ
ÿ
ÿÿÿÿÿÿÿÿÿÿÿÿÿ
5ÿÿ





 ! 
"
#ÿ!ÿ!
# 

5
$ÿ6913#%
316293511
&'&(ÿ)&*)
+,-./ÿ)0+&1
(&0*+,)*2*30ÿ)4+3.5
2ÿ6
789:;8ÿ=>8ÿ?@AA8?ÿB?:9
=>8ÿC:?D8?EÿA8B:?8ÿ@E8
F
+2.)4,+*ÿ4+,*&0*3,.
16!9
G97
#61
024
11
G2!
G2!6



&35H3.5ÿ4(2*&I)*23.(&))ÿ)*&&(J
(2*K,+L")*&&(M0,2*&/J
LL
$
,1/&+ÿ0,2*ÿN42.*,.&ÿ229N
6$ ÿ#ÿ316293511O PQ6PQ1315 
616%0L26!6564
#8

012345673ÿ9623
10343ÿ373
37ÿÿÿÿÿÿÿÿÿÿÿÿÿ5623
4ÿ5623ÿ4137016
456
7373
5413
960
4316
163433740165035413
0023
132ÿ61540ÿ61
5034526
7523
5






!
!
"
"

0#ÿ 2$5
 
ÿ%
&'()*'ÿ,-'ÿ./00'.ÿ1.)(
,-'ÿ2).3'.4ÿ0'1).'ÿ/4'
5

6 7

"

6""
6"
956
256
26
89:;9<:ÿ=>?@8AB@?9<>8BBÿB@88>C
>?@DEFGB@88>HIE?@8JC
GG
#
EKJ8FÿIE?@ÿL=?<@E<8ÿ L
#43456ÿ41ÿ M435 NONO 956
$G?%
!
0F?<B=EF@ÿ=FE@8I@9E<
28P8>ÿB8@B
3>8I@FEB@?@9IÿB=F9<:
FEQ<JÿBIF8K

01223
04223
415
515
52
67
82
82
67
98
7
57
45
ÿ
ÿ
ÿÿÿÿÿÿÿÿÿÿÿÿÿ
4ÿÿ





!
"
9ÿ!ÿ!
9

4
#ÿ42529$
256172451
1ÿ%
&'()*'ÿ,-'ÿ./00'.ÿ1.)(
,-'ÿ2).3'.4ÿ0'1).'ÿ/4'
5
56!7
677
965
013
55
61!
61!6
898:ÿ;8<;
:8=<>?;<@<A=ÿ;B>ACD
>?ECFÿ;=>8G
652$0H@%!6423
>@C;B?><ÿB>?<8=<A?C
6# ÿ9ÿ256172451I JK52K5254 


 8ADLACDÿB:@<8M;<@AC:8;;ÿ;<88:N
:@<O?>H";<88:P=?@<8FN
HH
#
?GF8>ÿ=?@<ÿQB@C<?C8ÿ117Q