Kettler SVEN Champion 7043-190 User manual

Made in Germany
Weatherproof Tournament Table Tennis Table
SVEN®Champion
Owner’s Manual Model Number 7043-190
Printed on 100% recycled paper!
Absolutely Weatherproof
Thank you for purchasing our high quality KETTLER product.
If you have any questions or concerns regarding this product, please contact us:
KETTLER International, Inc. E-mail [email protected]
Parts & Service Department Tel: [phone] ext. 26
P.O.Box 2747 Fax: [phone]
Virginia Beach, Virginia 23450 USA
Please have this owner’s manual with you when you call.
DO NOT CONTACT YOUR RETAILER.

2
Assembly Instructions
Before assembling or using the table-tennis table, please read the following instructions carefully. They contain impor-
tant information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions
in a safe place for maintenance purposes or for ordering spare parts.
All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control
during manufacturing. The knowledge in this process is used to constantly improve and develop our products. In order to offer our cus-
tomers the very best in product quality, we reserve the right to make technical changes at any time. Should you have any cause for com-
plaint, please contact KETTLER at:
KETTLER International, Inc.
P.O.Box 2747
Virginia Beach, Virginia 23450 USA
Tel: [phone] ext. 26
Fax: [phone]
E-mail [email protected]
Note on Safety
■The table tennis table should be used only for its intended pur-
pose, i.e. for playing with suitable table tennis paddles and balls.
■All other uses are prohibited and may be dangerous. The man-
ufacturer cannot be held liable for damage or injury caused by
improper use of the table.
■Damaged or worn components may endanger your safety or
shorten the lifespan of the table tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufac-
tured by KETTLER.
■The table tennis table complies with all safety regulations. In-
correct repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the
safety of the user.
■Instruct other persons (in particularly children) using the table in
its correct use, and draw their attention to any potential source
of danger, especially folding or closing the table.
■When setting up or dismantling the table, stay clear of its fold-
ing radius.
■When folded up, the table tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a shel-
tered position.
■The unit complies with the standard DIN 7898-1/10.97.
■Depending on frequency of use, check all screws, bolts etc.
regularly to ensure that they are in good condition.
Handling the equipment
■Do not use the table tennis table until it has been fully and cor-
rectly assembled and checked.
■Set the table up on a level surface.
■For practising without a partner, the table halves can be fold-
ed up singly.
Limited One-Year Warranty (Residential use)
Manufacturer warrants to the original retail purchaser, this
product to be free from defects in material and workmanship for
a period of one (1) year from the date of purchase. Should this
product become defective due to material or workmanship within
the warranty period, contact our Customer Service Department
for repair or replacement at our opinion. This warranty is not
transferable and does not cover normal wear and tear, bowing
of the table or damage caused by improper handling, installation
or use of this product. This warranty is also void if product is in
any way abused, damaged, or modified from its original state,
or if used for other than residential use. This warranty gives you
specific legal rights, and you may have other rights which vary
from state to state.
If table does not seem level, it is probably because floor is not lev-
el. Move table several inches (set table in playing position) in dif-
ferent directions to find the best location for the table. If the floor
is extremely unleveled, table may not play or operate properly. If
table is high in the center, shim up under the outer legs.
■Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the en-
vironment. In most cases, a slightly dampened cloth is sufficient.

3
Instructions for Assembly
■Carefully read these assembly instructions before beginning
with the work itself. The individual steps are additionally ex-
plained in the sequence by means of symbols, in some cases a
text mark indicates that a written explanation is available.
Strictly follow the individual mounting steps to ensure a safe use
and operation of the unit.
■To ensure that the table-tennis table is properly assembled and can
be safely used, observe the instructions for assembly exactly.
■Please note that there is always a danger of injury when wor-
king with tools or doing manual work. Therefore please be ca-
reful when assembling this machine.
■Ensure that your working area is free of possible sources of
danger, for example don’t leave any tools lying around. Al-
ways dispose packaging material in such a way that it may not
cause any danger. There is always a risk of suffocation if child-
ren play with plastic bags!
■The fastening material required for each assembly step is sho-
wn in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
■Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand un-
til resistance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
■For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
■Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
2x M8
6x M6
4x M6
16x ø12
20x ø16
12x ø25
8x
4x 4x
2x
4x M8 2x ø20
2x
2x
4x
2x 2x2x2x1x
3x
6x M8x45
2x
2x
4x
4x M6x60
4x M6x35
6x M6x37
6x
2x
1x
2x
1x
2x
4x
2x
4x M8x110
2x M8x120
Checklist (contents of packaging)
You also need the following tools (Not included): SW13 SW10
2x 2x 1x

4
1
4x
4x
4x
!
!
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE

5
2
18,6cm
C
A
D
A
ø25
A
B
2x
2x
B
2x
2x 2x
C
8x
2x 2x
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE

6
3
4
C
8x
2x 2x
2x
2x
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE

7
4x
2x
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
5
6
To do this, the braces for the frame
must be bent slightly to the side. Pro-
ceed with care when doing this.
Ensure that it cannot slip or tilt over.
2x
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
4x
2x
2x

8
7
A
A
B
B
1x
1x 2x 1x
B
2x 4x 2x
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE
AACCTTUUAALLSSIIZZEE

9
8
10
9
CLICK!
CLICK!
Carry out steps 5–8 for the second half of the table. Again, ensure that the table cannot slip or tilt over!
4x

10
2
A
B
1 Handling
A
B
C
Folding the table halves down:
press the left-hand tip lock. Hold the ta-
ble firmly with one hand, press the
right-hand lock and lower the table-half
slowly into position. Never allow it to
drop down!
Folding the table halves up:
press the locking lever up and lift the ta-
ble half upwards. Continue to press the
lever during the first part of the upward
motion.

11
3 4
19mm Wood
22mm Aluminium
A Adjustment knob; pull knob off net post
and select desired thickness (i.e. 19mm)
B Slide the netposts between the table halves.
C Slide the tension pin through net
D Place pin in designated slots
E Tie tension string to plastic tension tab.
F Place tension string in slots over tension pin
and net post. Adjust net tension by adjust-
ing plastic tension tab.
A B
C
D
E
F
Spare parts list
Item Description Pieces Part No.
for 7043-190
(weatherproof)
Ordering spare parts
When ordering spare parts, always state the full product number, spare-part number, the quantity required and the control number stamped on the back.
Example order: Product No. 7043-190 / spare-part no. 10100046 / 2 pieces / inspection no......
Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.) is required, this should be clearly stated
on the order by adding the words „with fastening material“.
For parts, please contact us at:
KETTLER International, Inc. E-mail [email protected]
P.O.Box 2747 Tel: [phone] ext. 26
Virginia Beach, VA 23450-2747 USA Fax: [phone]
1TT-Platte (BITTE UNBEDINGT ARTIKEL-NUMMER DES TT-TISCHES ANGEBEN!) 2 94130003
2Fussbügel/-gestell mit Bodenschonern 2 94110769
3Bodenschoner 4 70130540
4Stützbügel (kpl. mit Rohrverbindern, Sicherungen und Bundschrauben M6x30mm) 2 94110771
5Sicherungshebel 1 4 94110762
6Sicherungshebel 2 2 94110763
10 Lagerböckchen 8 10128024
11 Schubstange mit Rohrverbinder 2 94110758
12 Schubstange (kpl. mit Sicherung, Bundschraube M6x30mm und Rohrverbindern) 2 94110755
13 Verbindungsstange 3 94110764
14 Grundbügel (714mm) 1 94110765
15 Radhalter 2 70130811
16 Grundbügel (890mm) mit Stopfen für VKT 25mm 1 94110767
17 Abweisstange 2 70130602
18 Seitenverkleidung 2 70130817
19 Räder-Satz (4 Stück) mit Radverbinder 2 94180177
20 Radverbinder 2 70130812
21 Handdruckplatte 6 70130530
22 Bundschraube M6x37mm (o.Abb.) 6 10201209
23 Rechteckmutter M6 4 10301000
24 Stopfen für VKT 25mm 2 10100046
25 6kant-Schraube M8x120mm (o.Abb.) 2 10206115
26 6kant-Schraube M8x110mm (o.Abb.) 4 10206081
27 Distanzrohr ø12x1,8x64mm 2 97201453
28 Spreizniet ø6x9,5 4 10418503
29 Schraubenbeutel 1 94180178
30 Netzhalter 2 10128022
31 Netz 1 73301010
32 Schläger-/Ballhalterung (o.Abb.) 1 70130561
33 Spannlasche 2 10128002
34 Klemme zu Schläger-/Ballhalterung (o.Abb.) 2 70130567

In case of complaint, please state this control number.
docu 934a/10.02
Spare parts drawing
10
1
3
6
4
15
14
21
5
12
21
17
5
11
2
20
27 16
24
18
13 23
28
19
31
32
33
30
10
19