Kettler SKYLON 6 User manual

Assembly instructions Table Tennis Table
„Indoor 6”
Art.-Nr. 07138-960
13
10
8
90 min.
– US – Adult Assembly Required
Please do not return this product to the store. Contact KETTLER®for parts and service: call toll free
866.804.0440 or send email to [email protected]. Please visit our web site www.kettlerusa.com to
view a video demonstration of product assembly.

2
Note on Safety
■ The table-tennis table should be used only for its intended pur-
pose, i.e. for playing with suitable table-tennis bats and balls.
■ All other uses are prohibited and may be dangerous. The ma-
nufacturer cannot be held liable for damage or injury caused
by improper use of the table.
■ Damaged or worn components may endanger your safety or
shorten the lifespan of the table-tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufactu-
red by KETTLER.
■ The table-tennis table complies with all safety regulations. In-
correct repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the sa-
fety of the user.
■ Instruct other persons (in particular children) using the table in
its correct use, and draw their attention to any potential source
of danger, especially when setting up or dismantling the table.
■ When setting up or dismantling the table, stay clear of its fol-
ding radius.
■ When folded up, the table-tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a shelte-
red position.
■ The table-tennis table may be pushed only into the transport po-
sition because there is otherwise a danger of injury.
■ The unit complies with the standard EN 14468–1:2004.
■ Depending on frequency of use, check all screws, bolts etc. re-
gularly to ensure that they are in good condition.
■ Caution: While assembly of the product keep off children’s
reach (Choking hazard - contains small parts).
■ In case of enquiry, please contact your KETTLER dealer.
Handling the equipment
■ Do not use the table-tennis table until it has been fully and cor-
rectly assembled and checked.
■ Ensure that table-tennis tables which are not weatherproof are
not exposed to dampness or rain. Keep them well away from
direct sources of heat. Should the surface become warped, lay
the table on a level surface for a few days.
■ Set the table up on a level surface.
■ Do not cover it with plastic foil, under which condensation may
form. We recommend the weatherproof KETTLER tarpaulin, art.
no. 7032-300.
■ For practising without a partner, the table halves can be folded
up singly.
■ For more information on the sport of table-tennis, you are re-
ferred to the specialist literature on the subject.
■ Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment. In most cases, a slightly dampened cloth is suffi-
cient.
■ Waste Disposal: KETTLER products are recyclable. At the end of
its useful life please dispose of this article correctly and safely
(local refuse sites).
Please read these instructions carefully prior to carrying out assembly and using for the first time. They contain in-
formation which is important for your safety as well as for the use and maintenance of the appliance. Keep these
instructions in a safe place for reference purposes, maintenance work and to assist you when ordering spare parts.
– US – Important Instructions
Instructions for Assembly
■ The equipment must be assembled with due care by two adult
persons.
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■ Please note that there is always a danger of injury when wor-
king with tools or doing manual work. Therefore please be ca-
reful when assembling this machine.
■ Ensure that your working area is free of possible sources of dan-
ger, for example don’t leave any tools lying around. Always
dispose packaging material in such a way that it may not cau-
se any danger. There is always a risk of suffocation if children
play with plastic bags!
■ The fastening material required for each assembly step is sho-
wn in the diagram inset. Use the fastening material exactly as
instructed.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function cor-
rectly (the locking device is destroyed), and must be replaced.
■ For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary. Goods may only be retur-
ned after prior arrangement and in (internal) packaging, which is
safe for transportation, in the original box if possible. It is important
to provide a detailed defect description / damage report!
List of spare parts
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see spare parts drawing).
Example order: Art. no. 07138-970 / spare-part no. 10100016
/ 2 pieces / S/N......
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material“.
KETTLER GB Ltd.
Kettler House, Merse Road
North Moons Moat
Redditch, Worcestershire B98 9HL
www.kettler.co.uk
GB
[phone]
[phone]
[e-mail]-mail:
KETTLER International Inc.
1355 London Bridge Road
Virginia Beach, VA 23453
www.kettlerusa.com
USA
[phone]
[phone]
[e-mail]-mail:

3
2
5
5
5
5
1
1
1
1
4x M8x110
4x M8
2
2x M8x65
2x
ø25x8,4
2x 66 mm
3
4x
4x 4x
8x 3,9x16
4
4
4
4
4
4x M6x90
4x
4x
12x6,4x12
12x6,4
8x 3,9x16
4x 26x19x6
6
6
6
6
4x M8x65
4x
ø25x8,4
4x
4x
ø12x5,3
4x M5
4x 3,9x16
4x M5x16
7
7
7
7
4x
ø12,5x6,4
4x M6
1
Pay attention to the numbering of the bag of screws!
Checklist (contents of packaging)
– US –Please use the cardboard packaging during mounting as underlay in order to avoid
scratching and damaging the product.

4
– US – You also need the following tools (Not included):
123
123
1x
2x
2x
2x
4x
4x
2x
2x
2x
2x
8x
2x
1x/4x
3x
13
10
8
90 min.
Checklist (contents of packaging)
/

5
Exemple Exemplos Příklady
Példák Exempel
Beispiele
Measuring help for screw connections
1 a
2x
M8x110
1x
1x
M8
13
1
2x

1 b
2x
6
1
2x
M8x110
1x
1x
M8
13
!
2
M8x65
2x
ø25
2x
13
66mm
2x
2

7
3 b
13
A
2x
2x
D
2x
E
4x
AB
A
C
D
E
2x
3,9x16
3
2x
– US – A flat subsurface free from foreign objects is required for
assembly steps image 3b to image 4c. For this use the un-
damaged lid of the packaging box as a subsurface. You
must ensure that no screws or other fasteners or foreign
objects are on the cardboard base.
3a
A) Insert lock pin into hole and push through until it is
seated flush against frame and while holding lock pin in
place, attach “L” shaped guide block and press together
until both the guide block and lock pin are both seated
flush against the frame.
B) Use 13 mm wrench to hold lock pin steady and rotate
"L" shaped guide block ¼ turn counter-clockwise to secu-
re the lock pin and guide block together.
C) Position the "L" shaped guide block as shown in ima-
ge above.
D) Place retaining clip into position which keeps lock pin
and guide block secured together
E) Attach the outer half of guide block using two 3.9 x
16 screws from hardware bag #3 and then repeat all
steps for opposite side. Also repeat all steps for the
other table half.

4 a
8
4
ø3,9x16
4x
A
B
2x
4 b 4
A
B
M6x110
2x
ø12x12 mm
2x
ø12x2 mm
2x
10
A
2x
B
2x

9
4 c 4
2x
ø 26 mm
A
B
B
2x

10
2x
2x
2x
ø 25 mm
M8x65
13
A
B
C
C
E
E
D
5
2x
5

11
6 c
6 b
6 a 6
A
B
ø3,9x16
2x
M5x16
2x
ø12
2x
M5
2x
8
6
6
2x 2x

7 b
12
B
A
M6
2x
12,5x6,4
2x
10
7
2x
7 a

13
8
9
B
A
C
D
A
B
2x
4x

14
B
A
A
B
10
– US – Folding the table halves
11
– US – Unfolding the table halves

15
max 1 cm = ok.
max 1 cm = ok. max 1 cm = ok.
STOP
+/– 5 mm
12
– US – Handling

16
A
C
D
B
12
– US – Handling

17

18
7
2
6
3
2
5
11
50
51
4
72
73
Spare parts order
Spare parts drawing and list

19
12 94138970
22 94111711
32 94111709
44 70120864
62 94111687
94 94111713
10 3 94111694
11 4 40120143
12 4 40120144
.14 2 94608258
15 2 94319409
16 2 70130848
18 4 97201441
20 1 94180697
21 2 94608241
22 8 10100232
23 4 10100030
30 2 70120914
31 2 70120915
32 2 94319410
33 1 94180681
34 2 10128013
35 2 94608237
36 4 57132900
38 4 10209011
39 2 70130825
40 4 70130525
41 2 94319407
42 2 97202847
45 4 10100009
47 4 70130890
48 4 70130830
49 2 25058709
50 1 94180741
51 1 94180744
58 2 70120916
59 2 94180734
60 4 70113757
61 4 70120886
62 4 70120891
63 2 94111836
64 2 94111683
65 2 94111684
66 2 70120948
67 4 94111688
68 8 10107067
69 4 70130859
70 8 70120888
71 8 70120889
72 1 07090-701
73 1 07222-550
qty. . . part no..
# 07138-960
INDOOR 6
Spare parts list (PLEASE ALWAYS QUOTE THE TT TABLE ARTICLE NUMBER AS WELL.)

docu 4275/08.18
KETTLER GmbH · Hauptstraße 28 · D-59469 Ense-Parsit
www.kettler.de
!
!