Keurig K150 User manual

1
Owner’s manual
Keurig® K-Cup® K150 Brewer
manuel D’uTIlIsaTIOn
Cafetière à K-Cup® K150 de Keurig®

2
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic
safety precautions should be followed,
including the following:
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
3. This appliance must be properly
installed and located in accordance
with these instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock
and injury do not immerse cords, plugs,
or the appliance in water or any other
liquid.
8. Do not overfill the Water Reservoir
with water.
9. Use only water in this appliance! Do
not put any other liquids or foods in the
Water Reservoir except as instructed in
the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
12. Do not operate any appliance with a
damaged cord or plug or after
the appliance malfunctions or is
damaged in any manner. Contact
Keurig Customer Service to report
any malfunction of or damage to the
brewer.
13. Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
14. To disconnect, press the Power Switch
on the brewer to “OFF” status and then
remove the plug from the wall outlet.
15. Close supervision is necessary when
any appliance is used by or near
children.
16. Do not lift the Handle while
brewing is in progress.
17. Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
18. This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The appliance must
be grounded using a 3-hole properly
grounded outlet. In the event of an
electrical short circuit, grounding
reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or
remove the third (ground) prong from
the Power Cord or use an adapter.
21. Consult a qualified electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
22.Do not use the appliance for other than
its intended use.
23.The Water Filter Starter Kit (#5072)
and cartridges (#5073) are compatible
with the K150 brewer but are not NSF
certified. Use of these accessories will
void NSF certification.
24. Always brew with the Puncture Plate
(item R on page 5) installed. Failure to
do so will result in a failure to properly
brew.
SAVE THESE
INSTRUCTIONS.

3
Removing the serial number label from the brewer will void warranty.
TABLE OF CONTENTS
KEURIG®GOURMET SINGLE CUP BREWING SYSTEM
KEURIG®K150 — Using Your Brewer
SET-UP
Helpful Hints........................................................................................4
Unpacking ............................................................................................4
Features ...............................................................................................5
SECTION 1—SET-UP & FIRST BREW
Set-Up & First Brew ...........................................................................6
SECTION 2—MENU CONTROLS & INDICATORS
Setting the Clock............................................................................... 12
Programming Brew Temperature .................................................12
Programming Brew Size .................................................................13
Programming On/Off Features ......................................................13
SECTION 3—CLEANING & MAINTENANCE
Cleaning..............................................................................................15
De-Scaling..........................................................................................16
Storage ...............................................................................................17
SECTION 4—TROUBLESHOOTING..................................................18
SECTION 5 —WARRANTY................................................................ 19
Pour des directives en français, veuillez vous reporter à la page 20.
Record your Brewer Serial Number here.
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use brewer unless there is adult
supervision. Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER
USING A HOT COCOA K-CUP® PACK, RUN a Hot Water Brew Cycle
without a K-Cup®pack to avoid the possibility of clogging the Exit
Needle. DO NOT assume the next user will do this.
CAUTION: There are two sharp needles that puncture the K-Cup®pack, one above the
K-Cup®Pack Holder and the other in the bottom of the K-Cup®Pack Holder. To avoid
risk of injury, do not put your fingers in the K-Cup®Pack Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup®Pack Holder during the
brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup®
Pack Assembly Housing during the brewing process.
CAUTION: Please always keep the brewer in its upright position to avoid potential
injury and/or damage to your brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the
risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or extension
cord should be at least as great as the electrical rating of the appliance; (2) the cord
should be arranged so that it will not drape over the countertop or tabletop where it can
be pulled on by children or tripped over unintentionally; and (3) the extension cord must
include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD AND COMMERCIAL USE.
WARNINGTHIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN !

4 5
Set-up
Helpful Hints
1. Keep your brewer turned “ON” at all times.
To brew a fresh cup of coffee, tea or hot cocoa
anytime you want, we suggest you keep your
brewer turned “ON” all the time. However, the
brewer is fully programmable so you can set it
to turn on and off automatically to match your
schedule. Or, if you prefer, set the brewer to
automatically turn off after a period of time.
Follow the simple instructions on pages 13–14 to
make using the brewer convenient for you.
2. For the best tasting gourmet coffee, tea or
hot cocoa, Keurig recommends using bottled
water or the Keurig™ Water Filter Starter Kit
(available at www.keurig.com).
Water quality varies from place to place. If you
notice an undesirable taste in your cup of
coffee, such as chlorine or other mineral tastes,
we recommend you consider using bottled water
or water from a filtration system. The Keurig™
Water Filter Starter Kit is compatible with the
K150 brewer but is not NSF certified. Use of this
accessory will void NSF certification.
3. Customize the Size, Flavor & Brew That’s
Perfect for You.™
With the choice of over 250 varieties of K-Cup®
packs and 5 brew sizes (Small Cup-4 oz.,
Small Mug-6 oz., Medium Mug-8 oz., Large
Mug-10 oz. and Travel Mug-12 oz.) your Keurig®
brewer gives you endless options to custom-
ize the size, flavor and brew that’s perfect for
you. For a strong, intense cup, select an Extra
Bold K-Cup®pack (with up to 30% more ground
coffee than regular varieties) and brew the size
that’s right for you. The smaller the brew size,
the more intense flavor in your cup. The larger
the brew size, the less intense flavor in your cup.
4. Plug brewer into its own grounded outlet.
If the electric circuit is overloaded with other
appliances, your brewer may not function
properly. The brewer should be operated on its
own circuit, separate from other appliances.
5. Brewing into a travel mug.
To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.
6. De-scale brewer regularly.
Please see pages 16 and 17 for instructions.
Unpacking Instructions
1. Place brewer box on a large steady surface
(such as a table or countertop) or on the floor.
Open the box.
2. Remove enclosed literature and K-Cup®
variety pack.
3. Turn the box on its side with the front of the box
facedown.
4. Reach into the box and grasp the foam insert
that contains the brewer.
5. Carefully pull the foam insert toward you and
out of the box. The brewer will still be encased
in the polyfoam and be on its side.
6. Remove the top polyfoam packaging material.
7. Carefully lift brewer off of the bottom polyfoam
and place it upright on a flat, steady surface.
8. Lift plastic bag off of brewer.
9. Record the serial number for this brewer on
page 3 of this guide. The serial number can be
found on the side of the brewer box or on the
bottom of the brewer.
10. Place the brewer upright on a flat, steady
surface. Remove tape holding Water Reservoir
in place.
We recommend you save all packing materials in
case future shipping of the product is necessary.
WARNING:
Keep all plastic bags away
from children.

5
A. Water Reservoir Lid
B. Water Reservoir
C. Water Reservoir
Lock Tab Slots
A
M
C
I
L
K
J
F
E
B
P
N
0
D. Handle
E. K-Cup®Pack Holder Funnel
F. K-Cup®Pack Holder
(E and F are the K-Cup®
Pack Holder Assembly)
G. K-Cup®Pack
Assembly Housing
H. Lid
I. Drip Tray Base
J. Drip Tray
K. Drip Tray Plate
L. LCD Screen
M. BREW Button
N. Housing
O. Power Switch
P. Power Cord
Q. Removable Float
R. Removable Puncture Plate
H
G
D
Features Keurig®— Model K150 Brewer
Keurig®K150 Brewer
Q
R

6
SECTION 1 Set-Up & First Brew
Setting Up Your Brewer
1. Remove all pieces of packing tape from the
brewer and Drip Tray. Remove the clear plastic
film from the LCD Display. Unwrap cord and
plug the brewer into a grounded outlet.
2. Turn the brewer on, the Power Switch is
located at the top left hand side of the brewer
on the back. The brewer’s LCD Display will
display the power up welcome screen (fig. 1).
3. Remove the Water Reservoir from brewer
by first removing Lid from the Water Reservoir
then lifting the Water Reservoir straight up
and toward the right of the brewer (may be
tight). Rinse the Water Reservoir thoroughly
with fresh, clean water.
IMPORTANT: You cannot use your Keurig®brewer
until it has been set up for its first use.
NOTE: If brewer has been exposed to temperatures
below freezing, allow brewer at least two hours to
reach room temperature before brewing. A frozen
or extremely cold brewer will not operate.
4. Fill the Water Reservoir up to the
fill mark with fresh, clean water.
Replace the Water Reservoir on
the brewer making sure that the
locking tabs engage with the
brewer (fig. 2). Replace Lid on
Water Reservoir.
5. The brewer will automatically fill
the Internal Hot Water Tank with
water and then the water will
be heated. This will take about
3 minutes. During the heating
period, “HEATING PLEASE WAIT”
will be displayed on the LCD
Screen (fig. 3).
6. Place a 10 oz. mug on the Drip Tray Plate,
then fully raise and lower the Handle. The
Brew Button will now be illuminated. Press
the Brew Button to start a cleansing brew.
NOTE: A K-Cup®pack should not be used for
this sequence.
7. When the cleansing brew is complete, the
brewer will go into its idle state and will be
ready to brew your first K-Cup®pack.
fig. 3
fig. 1
fig. 2
Welcome To The
Keurig®150 Brewing
System Designed
For The K-Cup®Pack
Español Français
Heating...
Please Wait

7
7. There may be a short pause prior to coffee
being dispensed. The entire brew process
lasts for approximately 1 minute and ends
with a burst of air to remove all liquid from
the K-Cup® pack.
CAUTION: There is extremely hot water in
the K-Cup®Pack Holder during the brew
process. To avoid risk of injury, do not lift the
Handle or open the K-Cup®Pack Assembly
Housing during the brew process.
8. The end of brew is indicated by “KEURIG
BREWED ENJOY”.
9. Lift the Handle, remove and dispose
of the used K-Cup®pack.
CAUTION: K-Cup®pack will be hot.
10. Enjoy your first cup of Keurig Brewed®
gourmet coffee, tea or hot cocoa!
11. Your brewer may display “HEATING
PLEASE WAIT” as it heats water for the
next brew cycle.
Ready to Brew Your First Cup
1. The LCD Display will be in its idle state (fig. 4).
2. Lift the Handle. The K-Cup®Pack Holder
will open toward you (fig. 5).
3. Select a K-Cup® pack.
NOTE: Do not remove the foil lid
or puncture the K-Cup®pack.
4. Place a K-Cup®pack
in the K-Cup®Pack Holder (fig. 6).
CAUTION: There are two sharp needles that
puncture the K-Cup®pack, one above the K-Cup®
Pack Holder and the other in the bottom of the
K-Cup®Pack Holder. To avoid risk of injury, do
not put your fingers in the K-Cup®Pack Assembly
Housing.
5. Lower the Handle to close the Lid over the
K-Cup®Pack Holder. (When it is closed
completely, the BREW Button will flash up to
60 seconds.)
6. Place a mug on the drip tray and select
your brew size (fig. 7), then press BREW (fig. 8).
NOTE: If you do not press BREW within 60
seconds the brewer will return to its idle state
and the Brew Button will cease to flash to prevent
accidental activation. Re-activate by lifting the
handle fully and then closing it.
fig. 4
fig. 6
fig. 5fig. 7
fig. 8
12:30 PM
Ready
Choose Your
K-Cup®Pack
& Lift Handle
WATER
LEVEL
Español Français
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.
Place Mug,
Select
Brew Size

8
Stopping the Brew Process
If you need to stop the brewing after the process has started, press and
release the Power Switch to turn the brewer ‘OFF’. The flow of coffee, tea or
hot cocoa will stop and the heating element and the LCD Screen will shut off.
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next
brew. We recommend that you perform a cleansing brew with water only after a
terminated brew. Then your next brew will be the volume you have selected.
Adding Water
The LCD Display of your brewer will indicate
when the water level in the Reservoir is low
or if the Water Reservoir has been removed by
displaying the words “FILL WATER RESERVOIR”
(fig. 9). The brewer will not allow you to brew
when “FILL WATER RESERVOIR” is displayed
(fig. 9).
The Water Reservoir can be filled in three ways.
1. Remove the Water Reservoir from brewer by
first removing Lid from the Water Reservoir,
then lifting the Water Reservoir straight up
and toward the right of the brewer. Fill with
water. Place the Water Reservoir back on the
brewer and replace the Lid.
IMPORTANT: Do not remove the Water Reservoir
during the brewing process.
2. Lift off the Water Reservoir Lid and pour
water directly into the Water Reservoir
while it is still attached to the brewer,
then replace the Lid.
3. The brewer can also be connected directly into
the water line. To order a K150 Direct Plumb Kit
please call 1.888.CUP.BREW (287.2739).
SECTION 1 Set-Up & First Brew (continued)
fig.9
2. Fill Water Reservoir

9
Brewing Hot Water
Your brewer is able to produce hot water for making hot cocoa from a
packet, or for use in cooking, for making soups, etc. Simply follow the
instructions on page 7, “Ready To Brew Your First Cup” without adding a
K-Cup®pack. NOTE: After brewing a hot cocoa K-Cup® pack, we recommend
running a hot water brew cycle without a K-Cup® pack.
Purging the Brewer
If your brewer has not been used for more than one week, you should purge
the water from the internal water tank.
1. If there is water in the Water Reservoir, remove the Lid, then lift the
Water Reservoir straight up and away from brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Be sure the brewer is turned ‘ON’. Lift and lower the Handle on the brewer
without inserting a K-Cup®pack.
3. The LCD Display will be in its idle state (fig. 4).
4. Place a large mug on the drip tray and
select Large Mug (10 oz. serving) brew size
from the Select Brew Size Menu (fig. 10).
5. Discard water.
6. Repeat steps 2 - 5 two more times to
completely purge water from the Internal
Hot Water Tank.
fig.10
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.
Place Mug,
Select
Brew Size

10
Menu Mode
To enter the MENU MODE the brewer’s power must be off. Press and hold
your finger on the display while pressing and releasing the Power Switch.
Continue pressure on the display for 5 seconds (fig. 11). The MENU screen
will appear (fig. 12).
Press any line item to enter the set up for that particular feature.
Please reference the Menu navigation on page 11.
If you are experiencing any problems with your brewer, please contact
Customer Service at 1.888.CUP.BREW (287.2739).
5 seconds.
SECTION 2 Menu Controls & Indicators
Home
Auto OFF
Brew Temp
Language
Clock
ON/OFF Time
Brew Size(s)
Contact
fig. 11
fig. 12

11
Home
Auto OFF
Brew Temp
Language
Clock
ON/OFF Time
Brew Size(s)
Contact
Menu Key Navigation
Home
Press HOME at any time to return your brewer to an idle state.
Clock
Setting the clock is optional. To program the clock, follow the
instructions on page 12.
Brew Temp
The brew temperature is pre-set at 193˚F. You do not have to set
the brew temperature but you can adjust it up or down by 5˚.
Simply follow the instructions on page 12.
Brew Size(s)
Five brew sizes are available: 4 oz., 6 oz., 8 oz., 10 oz., and 12 oz.
To program the brew sizes see page 13.
Auto OFF
Auto Off allows you to program your brewer to automatically turn off two
hours after the last brew. See page 14 for programming instructions.
ON/OFF Time
You can leave your brewer on all the time and use the Power Switch to turn
it off. Or you can program the brewer to brew at a specific time as shown
on page 13.
Language
This brewer is shipped with English as the default language.
To change the language, follow the instructions on page 14.
Contact
The contact setting features allows you to program the contact
information you need for brewer support and help. To program,
follow the instructions on page 14.

12
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the
LCD Control Center. NOTE: You must set the clock if you will be programming
the Auto On/Off Time feature.
1. From the Menu Mode, press “CLOCK”.
2. The set clock screen will display
“DISABLED” if the brewer is new or if
electrical power has been interrupted.
Press “DISABLED” to set a time. Press H
repeatedly to advance the hour in steps or
hold it down to scroll through the hours
quickly. When you have set the hour then
press the M to set the minutes, press
repeatedly to advance by a minute each time
or keep it pressed to scroll quickly (fig. 13).
3. Press “OK” when you are finished.
The Clock is now set.
4. The correct time should now be displayed in
the LCD Home Screen.
fig.13
Programming Brew Temperature (188°–198º F)
The brewer brews at a preset temperature of 193°F. You can adjust this
temperature up or down by 5°. Simply follow the instructions below.
1. From the Menu Mode, press “BREW TEMP”.
2. The LCD Display will now display the Brew
Temperature programming options (fig. 14).
The temperature 193°F (initial setting) will
be displayed at the top of the LCD Display
to indicate the current temperature setting.
3. Press the + symbol to increase the
temperature and the – symbol to lower the
temperature one degree at a time.
4. Once you have reached your desired brew
temperature, press “OK”. The Brew
Temperature is now set.
5. To change the brew temperature, repeat
steps 1 through 4.
NOTE: At high altitudes (over 5,000 feet)
if boiling occurs, use the temperature
adjustment (-5°) to lower the temperature.
Clock
12:00 AM
OK
MH
193°F
+-
Temperature
OK
fig.14 fig.14
NOTE: If power is interrupted to the brewer, follow the procedure above to
reset the time as the clock will not be visible. Brew size and brew
temperature menu settings will be restored automatically. All other
settings will be restored automatically after clock is set.
NOTE: To disable the clock, press the time. However, the ‘On/Off’ time setting
will also be disabled.
SECTION 2 Menu Controls & Indicators (continued)

13
Programming Your Brew Size
All brew sizes are enabled in the default setting. If you want to disable any
brew size, just press on the appropriate icon(s). Please follow instructions
outlined below.
1. From the Menu Mode, press
“SET BREW SIZE(S)”.
2. The LCD will display all enabled brew sizes.
To disable a brew size press the icon. The
check mark will change to an “X” indicating
that the brew size is disabled (fig. 15).
3. Once you have selected your desired brew
size(s), press “OK”. The brew size(s) are now
set.
NOTE: You can not delete all brew sizes.
To enable a brew size you have already
disabled, just press its icon and then press
“OK”. The 8 oz. setting is the default brew size
if all sizes have been disabled.
Programming On/Off Features
The brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule.
1. Leave it ON all the time. The brewer can be
left on all the time so that it is always ready
to brew a fresh cup of gourmet coffee, tea or
hot cocoa. To turn the brewer off at any time,
simply press and release the Power Switch.
Press and release the Power Switch again
to restore power to the brewer. You will have
to wait for the water to heat up before the
brewer is ready to brew.
2. Program the brewer for a specific On/Off
Time. NOTE: To use this programming feature,
the clock must be set to the correct time.
fig.15
fig.16
a. After setting the correct time (see “Setting The Clock” page 12), return to
the Menu Mode and press “ON/OFF TIME”.
b. To set the ON time, press “DISABLED”. The display will change to a time of
day. Press “H” to set the hours and “M” to set the minutes. Once the
desired time is set, press “OK” to accept this time.
c. To set the OFF time, press “DISABLED”. The display will change to a time
of day. Press “H” to set the hours and “M” to set the minutes. Once the
desired time is set, press “OK” to accept this time (fig. 16).
ON/OFF Time
ON 12:00 AM
OFF 12:00 PM
OK
MH
MH
4 OZ.
12 OZ.
6 OZ.
10 OZ.
8 OZ.
OK
3
3
3
3

14
SECTION 2 Menu Controls & Indicators (continued) Setting Contact Screen
The contact screen is pre-programmed with
the following information: Keurig, Incorporated.
and www.keurig.com.
You can reprogram the brewer with your contact
information. The contact screen will appear in
the screen saver.
1. From the Menu Mode, press “CONTACT”.
The LCD screen will display the Keurig
default contact information (fig. 19).
2. Press the Upper (Company Name) Box. The
Keypad will appear along with the current
information (fig. 20). NOTE: Unless changed
by the user, Keurig contact information will be
present on the display.
a. Press Delete Key repeatedly to remove
current information. Enter new information
using the Keypad.
NOTE: To select Upper Case, Lower Case,
Numerals, Upper Case Accents, Lower Case
Accents, press the Keypad Change Key located
at the bottom center of the screen.
fig.19
fig.20
fig.18
WWW.KEURIG.COM
PHONE #
KEURIG,
INCORPORATED
Contact
OK
Language
Español
English
Français
OK
3. Set the brewer to “AUTO OFF” to automatically
turn off 2 hours after the last brew.
a. From the Menu Mode, press “AUTO OFF”.
The LCD Display will now display the
“AUTO OFF” programming option (fig.17).
b. To enable the “AUTO OFF” feature, press “ON”.
“ENABLED” will appear on the screen and
press “OK”. To disable the “AUTO OFF” feature,
press “OFF”. “DISABLED” will appear on the
screen and press “OK”.
Language Settings
The brewer is shipped with English as the default
language. To change the default to Francais or
Espanol, follow the instructions outlined below.
Set Language
1. From the Menu Mode, press “LANGUAGE”.
2. The LCD Display will now display the
Language programming options (fig. 18).
3. Press the desired Language button, then
press OK to confirm your selection.
fig.17
Auto OFF
Auto Off 2 hours
After Last Brew
OK
OFFON
ABC DEF
GHI JKL MNO
PQRS TUV WX Y Z
Delete . , - Space
KEURIG,
INCORPORATED
OK
ABC
abc
123

15
b. Press “OK” to save your changes and
return to the Main Contact Screen.
NOTE: Pressing the Back Arrow Key will
return to the Main Contact Screen without
saving changes.
3. Press the Middle (Phone Number) Box. The
Numeral Keypad Mode will appear along
with the current information (fig. 21).
a. Delete current phone number and enter
new information using the Keypad.
b. Press “OK” to save your changes and
return to the Main Contact Screen.
4. Press the Lower Box. This box can be
customized to contain any information
such as web/email address, contact
name, etc (fig. 22).
a. Enter new information using the Keypad.
b. Press “OK” to save your changes and
return to the Main Contact Screen.
c. In Main Contact Screen (fig. 19), press “OK”
to save the updated screen as the default
and return to the Menu Screen.
fig.21
SECTION 3 Cleaning & Maintenance
Cleaning External Parts
Regular cleaning of the brewer’s external components is recommended.
The following section provides instruction for standard cleaning procedures.
For in-depth NSF certified instructions, please refer to the Cleaning and
Sanitization Guide.
1. Never immerse the brewer in water or other liquids. The Housing
and other external components may be cleaned with a damp, soapy,
non-abrasive cloth.
2. The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray
and Drip Tray Plate should be periodically inspected and rinsed clean.
To remove the Drip Tray Assembly, simply slide it toward you, keeping it
level at all times to avoid spilling. The Drip
Tray and Drip Tray Plate should not be placed
in the dishwasher. They should be cleaned
with a damp, soapy, non-abrasive cloth and
rinsed thoroughly.
Cleaning the K-Cup®Pack
Holder Assembly
1. Cleaning the Parts—The K-Cup®Pack
Holder Assembly can be placed onto the top
shelf of a dishwasher. NOTE: Use low
temperature cycles in the dishwasher. To
remove the K-Cup®Pack Holder Assembly
from the brewer, open the cover by lifting
the Handle.
fig.23
fig.22
21 3
456
789
Delete 0Space
PHONE #
OK
ABC
abc
123
ABC DEF
GHI JKL MNO
PQRS TUV WX Y Z
Delete . , - Space
WWW.KEURIG.COM
OK
ABC
abc
123

16
Grasp the top of the K-Cup®Pack Holder with
one hand while pushing up on the bottom of the
K-Cup®Pack Holder from underneath with the
other until it releases (fig. 23). After cleaning,
align the K-Cup®Pack Holder with the opening
using the two front ribs as a guide, and snap
them into place from the top.
2. Cleaning the Funnel—The Funnel can be
removed from the K-Cup®Pack Holder by
pulling on it until it pops off (fig. 24). The Funnel
is dishwasher safe. To replace it, just snap it
back onto the K-Cup®Pack Holder Assembly.
3. Cleaning the Exit Needle—The Exit Needle is
located on the inside bottom of the K-Cup®
Pack Holder Assembly. Should a clog arise due
to coffee grinds, it can be cleaned using a paper
clip or similar tool. Remove the K-Cup®Pack
Holder Assembly and detach Funnel. Insert the
paper clip (as shown in fig. 24) into the Exit
Needle to loosen the clog, then flush with water.
The K-Cup®Pack Holder Assembly can be
placed onto the top shelf of a dishwasher.
NOTE: Use low temperature cycles in the
dishwasher.
4. Cleaning the Puncture Plate—The Puncture Plate can be removed by
grasping the finger grips of either side and pulling forward (fig. 25).
SECTION 3 Cleaning & Maintenance (continued)
!
fig.24
Once removed, spray the Puncture Plate with detergent, brush clean and
rinse if necessary. Be sure to replace the Puncture Plate after cleaning to
ensure proper brewer operation.
CAUTION: There are sharp needles that puncture the K-Cup®pack above the
K-Cup®Pack Holder and in the bottom of the K-Cup®Pack Holder. To avoid
risk of injury, do not put your fingers in the K-Cup®Pack Assembly Housing.
Cleaning the Water Reservoir & Water Reservoir Lid
The Water Reservoir Lid or Water Reservoir should not be put into the
dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth
and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a
cloth as lint may remain. CAUTION: Please rinse the Water Reservoir
thoroughly after cleaning to ensure that no cleaners or cleaning solutions
remain in this area as they may contaminate the water supply in the brewer.
De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the mineral
content of the water in your area, calcium deposits or scale may build up in
your brewer. Scale is non-toxic, but left unattended, it can hinder brewer
performance. De-scaling your brewer helps maintain the heating element
and other internal parts of the brewer that come in contact with water.
The brewer should be de-scaled every 3-6 months to ensure optimal
performance. It is possible for calcium deposits to build up faster, making it
necessary to de-scale more often.
Properly follow the de-scaling procedure described on page 17.
fig.25

17
De-Scaling Instructions
A. PREPARE
Step 1: Make sure you have at least 90 oz. of undiluted white vinegar
on hand. You will also need an empty sink and a large ceramic mug
(do not use a paper cup).
Step 2: Empty the water in the Water Reservoir.
Step 3: Disable “Auto Off” and programmed “On/Off” time (pages 13-14).
B. FILL AND CLEAN
Step 1: Pour approximately 90 oz. of the vinegar into the Water Reservoir.
Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle.
DO NOT USE A K-CUP®PACK just select the Large Mug brew size. Pour
the contents of the large mug into the sink.
Step 3: Repeat the brew process 3 times.
Step 4: Let the brewer stand for at least 4 hours while still on.
C. RINSE
Step 1: Ensure the Water Reservoir is filled with fresh water.
Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle.
Pour the contents of the large mug into the sink.
Step 3: Repeat brew process until the Water Reservoir is empty.
Step 4: You may need to perform additional cleansing brews if you notice any
residual taste or odor.
Service
Beyond these recommended cleaning and maintenance procedures this brewer is
not user serviceable. For service, please refer to the Warranty section of this guide.
Storage
Draining the Brewer
1. Turn off the brewer, unplug it, and allow the brewer to cool approximately
30 minutes.
2. Empty the Water Reservoir by first removing the Lid from the Water
Reservoir then lifting the Water Reservoir straight up and toward the right
of the brewer (may be tight). Rinse and Empty the Water Reservoir.
3. Turn the brewer around so the back is facing
out. Unscrew the small knob to release the
back panel, remove the panel from the
brewer, and set it aside. If the screw is tight,
you may need to use a flathead screw driver.
Pull the tube downward until the end is free
(fig. 25). Over a large pitcher, remove the
plug and drain the water from the Internal
Hot Water Tank into the pitcher. CAUTION: If
the brewer was not allowed to cool sufficiently,
the water draining from the tube may be very
hot. Re-cap the tube. NOTE: To avoid losing
parts, when finished, re-insert the tube and
screw the panel back onto the brewer.
fig.25

18
SECTION 4 Troubleshooting
SITUATION
Brewer does not
have power
Brewer will
not brew
SOLUTION
•Plug brewer into an independent outlet.
•Check to be sure that it is plugged in securely.
•Plug into a different outlet.
•Reset circuit breaker if necessary.
•Make sure that the Power Switch has been turned on
and LCD Display is illuminated.
• After placing the K-Cup®pack in the K-Cup®Pack
Holder, make sure the Handle is pushed down securely
and the LCD Control Center reads “READY TO BREW”
with the BREW Button flashing, then press the BREW
Button.
• The Exit Needle may be clogged (refer to page 16).
LCD Messages
• If the water reservoir is empty and needs to be refilled,
the LCD Screen will direct you to “Lift Water Reservoir,
Fill Water Reservoir, Replace Water Reservoir” with
slideshow of images. Follow these instructions.
• In pour-over mode, if the water flow has been
interrupted, the LCD Screen will state “Water Flow
Interrupted. To Reset, Please Lift and Remove Water
Reservoir”. When Reservoir has been removed, screen
states “If necessary, please fill water reservoir to Max
Fill Line. Then replace”. Follow these instructions.
• In plumbed mode, if the water flow has been interrupted,
LCD Screen will state “Water Flow Interrupted. To Reset,
Please Press Brew Button”. Follow these instructions.
• If the messages persist after following these
instructions, contact Customer Service at
1.888.CUP.BREW (287.2739).
SITUATION
Chlorine or mineral
taste in coffee
Brewing a partial cup
The time is not
displayed on the LCD
Message Center
Brewer shuts
off or turns on
automatically
SOLUTION
•Consider using bottled water, filtered water, or the
Keurig™Water Filter Starter Kit
(available at www.keurig.com).
•The Exit Needle may be clogged (refer to page 16).
•Clean the K-Cup®Pack Holder Assembly if necessary
and rinse under faucet (refer to pages 15-16).
•The Water Reservoir may have been removed
during brewing. Replace the Water Reservoir
and perform a water brew without a K-Cup®pack.
•“De-Scale” the brewer (refer to pages 16-17).
•If you have repeated the de-scale procedure on
your brewer two times and it is still only brewing
a partial cup, contact Customer Service at
1.888.CUP.BREW (287.2739).
•The time will not be displayed on the LCD
unless you have set it. To set the clock, follow the
procedure on page 12.
•If power is interrupted to the brewer, you will
need to set the clock again using the procedure
on page 12.
•Check to make sure that the Auto Off timer
and/or On/Off time features have not been set. To
do this, press the MENU Button below “MENU”
and scroll through the programming options.
“OFF” should be displayed for Auto Off timer and
On/Off. If “OFF” is not displayed, follow directions
on pages 13-14 to reset.
If any problems persist, contact Customer Service at 1.888.CUP.BREW (287.2739)

19
SECTION 5 Warranty
Limited One Year Warranty
Keurig, Incorporated warrants that your brewer will be free of defects in
materials or workmanship under normal use for one year from the date of
purchase. It is recommended that you fill out and return the warranty card
enclosed with your brewer so that your purchase information will be stored
in our system. Keurig will, at its option, repair or replace a defective brewer
without charge upon its receipt of proof of the date of purchase. If a
replacement brewer is necessary to service this warranty, the replacement
brewer may be new or reconditioned. If a replacement brewer is sent, a new
limited one year warranty will be applied to the replacement brewer.
This warranty only applies to brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
Only the use of Keurig Brewed®K-Cup®brand packs and accessories will
guarantee the proper functioning and lifetime of your Keurig®brewer. Any
damage to or malfunction of your brewer resulting from the use of non
Keurig Brewed®K-Cup®brand packs and accessories may not be covered by
this warranty or may result in a service fee if the damage or malfunction is
determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
Nor does this warranty cover damages caused by use of non Keurig Brewed®
K-Cup®brand packs or accessories, services performed by anyone other
than Keurig or its authorized service providers, use of parts other than
genuine Keurig®parts, or external causes such as abuse, misuse, inappro-
priate power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR K150 BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some
states or provinces do not allow disclaimers of such implied warranties or
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?
Keurig®brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.888.CUP.BREW (287.2739). Please do not
return your brewer for servicing without first speaking to Keurig Customer
Service to obtain an Authorization to Return number (ATR). Keurig®
brewers returned without an ATR number will be returned to the sender
without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.888.CUP.BREW (287.2739)

20
RÈGLES DE SÉCURITÉ IMPORTANTES
Fonctionnement et utilisation sans danger
Lors de l’utilisation de tout appareil électrique,
des mesures de sécurité de base devraient être
suivies, et notamment :
1. Lire toutes les instructions avant l’utilisation.
2. Ne pas toucher les surfaces chaudes. Utiliser
les poignées s’il y en a.
3. Installer correctement l’appareil et le placer
dans un endroit conforme aux présentes
instructions avant de l’utiliser.
4. L’utilisation d’accessoires non recommandés
par le fabricant de l’appareil risque de causer
un incendie, des chocs électriques ou des
blessures.
5. Éviter le contact ou la proximité de l’appareil
avec un élément électrique ou un brûleur à
gaz. Éviter également de placer l’appareil à
l’intérieur d’un four chaud.
6. Ne pas utiliser à l’extérieur.
7. Pour éviter les risques d’incendie, de chocs
électriques ou de blessures, ne pas immerger
la fiche, le cordon d’alimentation ou l’appareil
dans l’eau ni dans aucun autre liquide.
8. Ne pas trop remplir le réservoir d’eau.
9. Utiliser seulement de l’eau dans cet appareil!
Ne verser aucun autre liquide ou aliment dans
le réservoir d’eau, à moins d’indications à cet
effet dans les instructions de nettoyage.
10. Éteindre et débrancher l’appareil avant de
le nettoyer ou d’en faire l’entretien. Laisser
l’appareil refroidir avant d’ajouter ou d’enlever
des pièces et avant de le nettoyer.
11. Pour une utilisation optimale, brancher
l’appareil dans une prise de courant séparée
sur un circuit spécialisé pour éviter que les
lumières vacillent, que les fusibles sautent ou
que les disjoncteurs se déclenchent.
12. Ne jamais utiliser un appareil dont la fiche ou
le cordon d’alimentation est endommagé ou
un appareil qui présente un trouble de fonc-
tionnement ou qui a été endommagé. Commu-
niquer avec le Service à la clientèle de Keurig
pour signaler tout mauvais fonctionnement de
la cafetière ou tout dommage à celle-ci.
13. Ne pas laisser le cordon d’alimentation pendre
d’une table ou d’un comptoir ni entrer en
contact avec une surface chaude.
14. Pour débrancher la cafetière, éteindre d’abord
l’appareil en appuyant sur l’interrupteur, puis
retirer le cordon de la prise.
15. Ne jamais laisser des enfants utiliser
la cafetière ni rester à proximité sans
surveillance.
16. Ne pas soulever la poignée durant l’infusion.
17. Toujours laisser le couvercle sur le
réservoir d’eau, sauf lors du remplissage.
18. L’appareil est équipé d’un cordon
d’alimentation muni d’un fil et d’une prise de
mise à la terre. L’appareil doit être mis à la
terre en utilisant une prise de courant à contact
de mise à la terre à trois trous. En cas de
court-circuit, la mise à la terre réduit les
risques de chocs électriques.
19. Si la prise de courant est une prise de courant
murale standard à deux trous, le propriétaire
a l’obligation et la responsabilité de la faire
remplacer par une prise de courant de mise à
la terre à trois trous.
20. Il ne faut en aucun cas couper ou enlever la
troisième broche (mise à la terre) de la fiche du
cordon d’alimentation, ni utiliser un adaptateur.
21. Consulter un électricien qualifié si les instruc-
tions sur la mise à la terre ne sont pas parfaite-
ment comprises ou en cas de doutes sur la
mise à la terre de l’appareil.
22. Ne pas utiliser l’appareil à d’autres fins que
celle pour laquelle il a été conçu.
23.L’ensemble de départ pour filtre à eau (n
o
5072)
et les cartouches (n
o
5073) sont compatibles
avec la cafetière K150, mais ne sont pas homo-
logués par la NSF. L’utilisation de ces acces-
soires annulera l’homologation de la NSF.
24.Ne jamais infuser si la plaque de perforation
(article R à la page 23) n’est pas en place pour
assurer le bon déroulement du processus
d’infusion.
CONSERVER CE MANUEL.
AVERTISSEMENT AUX UTILISATEURS ET AUX PARENTS
1. NE permettezPAS aux enfants d’utiliser l’appareil sans
la supervision d’un adulte. L’appareil distribue de l’eau
très chaude.
2. AVIS SPÉCIAL AUX UTILISATEURS DE CHOCOLAT
CHAUD : APRÈS L’UTILISATION D’UNE DOSETTE K-CUP®
DE CHOCOLAT CHAUD, LANCEZ IMMÉDIATEMENT un
cycle d’infusion d’eau chaude sans dosette K-Cup®pour
éviter une possible obstruction de l’aiguille de sortie. NE
tenez PAS pour acquis que le prochain utilisateur le fera.