Key Digital FatCAT KD-CATHD250POH User manual

HDBT/HDMI “Lite” via Single CAT5e/6 (Tx/Rx)
Extenders with Full Buffer System, IR
HDBT/HDMI “Lite POH” via Single CAT5e/6 (Tx/Rx)
Extenders with Full Buffer System, IR, Power Over HDBT
The Experts in Digital Video Technology and Solutions™
KD-CATHD250Lite
KD-CATHD250POH
Key Digital®Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553
Phone : [phone] Fax : [phone] Web : www.keydigital.com
Rev 1 – Sept 2013
Key Digital
®
, led by digital video pioneer Mike Tsinberg,
develops and manufactures high quality, cutting-edge
technology solutions for virtually all applications where
high quality video imaging is important. Key Digital
®
is at the forefront of the video industry for Home
Theater Retailers, Custom Installers, System Integrators,
Broadcasters, Manufacturers, and Consumers.
Setup Guide
KD-CATHD250Lite_POH_Manual.indd 2-3 9/6/13 12:12 PM

4 1
Please read all instructions to insure safe operation of the product.
CAT6/STP CABLING IS STRONGLY RECOMMENDED FOR OPTIMUM
SIGNAL TRANSMISSION, ESPECIALLY IN HARSH ENVIRONMENTS
You MUST use the Power Supply provided with your unit or you VOID
the Key Digital
®
Warranty and risk damage to your unit and associated
equipment.
About KD-CATHD250Lite/POH
The FatCAT Series
™
KD-CATHD250Lite/POH allow extension of 1080p/60, 1920x1200,
3D signals up to 200 ft. on CAT5e/UTP; 250 Ft on CAT6/STP with KD-CAT6STP1X
cable. 4K signal extension is 120 ft. with all cabling. KD-CATHD250Lite/POH carry IR
and RS-232 for controlling remotely located equipment.
Key Features
➔Auto-adjustment of feedback, equalization and amplification depending
on the length of cabling used
➔Extends either IR or RS-232 control signals
➔Full support for 12-Bit Deep Color Video
➔Supports lossless compressed digital audio:
»Dolby
®
TrueHD, Dolby
®
Digital Plus and DTS
™
-HD Master Audio
Key Benefits
➔HDMI, IR and RS-232 signals combined over a single CAT cable
➔Daisy chaining of Tx and Rx units allow allows almost unlimited extension
of HDMI, RS-232 and IR signals
➔Supports HDBaseT
®
Technology
Advanced HDMI®Features
➔3D – Capability to pass 3D stereoscopic signal formats
➔4K – Capability to pass 4K by 2K resolutions
Accessories
➔(2) 5V 2A DC Power Supply (KD-CATHD250Lite)
»KD-CATHD250Lite requires power on both Tx and Rx units
➔(1) 12V 2A (KD-CATHD250POH)
»KD-CATHD250POH only requires power on the Tx unit,
which extends power to the Rx unit
➔(2) Mounting Brackets
➔(2) Locking HDMI Cable Clips
➔(1) Grounding Wire
Table of Contents
About KD-CATHD250Lite/POH .......................................1
Connections .....................................................2
Extending IR and RS-232 Control .....................................4
Application Example ...............................................4
Settings.........................................................5
Specifications ....................................................6
Important Product Warnings & Safety Instructions .........................8
How to Contact Key Digital ..........................................9
Warranty ........................................................9
© 2013 Key Digital, Inc. All rights reserved.
KD-CATHD250Lite_POH_Manual.indd 1 9/6/13 12:12 PM

2 3
Connections
Before making any connections, power off your source and display devices.
Tx Extender:
➔Using a short HDMI cable, connect your source device to the HDMI port labeled
“HDMI Input”. To connect DVI use appropriate DVI to HDMI adapters.
➔Connect the CAT cable on the Tx extender to the port labeled “CAT5e/6
Output”.
➔If desired, you can connect IR or RS-232 signals to the 3.5mm jack at this time.
Refer to the below pin assignment chart for pin assignments.
➔Tx Pin Assignment Chart
Mode Tip Ring Sleeve
IR IR In IR Out Gnd
RS232 RxD TxD Gnd
Rx Extender:
➔Using a short HDMI cable, connect your display device to the HDMI port labeled
“HDMI Output”.
➔Connect the CAT cable on the Rx extender to the port labeled “CAT5e/6 Input”.
➔If you are extending IR or RS-232 signals, connect them to the 3.5mm jack.
Refer to the below pin assignment chart for pin assignments.
➔Rx Pin Assignment Chart
➔
Mode Tip Ring Sleeve
IR IR Out IR In Gnd
RS232 TxD RxD Gnd
Power up the extenders using the included power supplies and then power up
your source and display equipment.
»KD-CATHD250Lite requires power on both Tx and Rx units
»KD-CATHD250POH only requires power on the Tx unit, which extends power
to the Rx unit
KD-CATHD250Lite_POH_Manual.indd 3 9/6/13 12:12 PM

4 5
Extending IR and RS-232 Control
You can extend IR or RS-232 control signals over the KD-CATHD250Lite/
KD-CATHD250POH baluns, for controlling remotely located equipment.
To extend control signals, follow the below pin assignment charts.
NOTE: The pin assignments are different on the Tx and Rx units.
➔Tx Pin Assignment Chart
Mode Tip Ring Sleeve
IR IR In IR Out Gnd
RS232 RxD TxD Gnd
➔Rx Pin Assignment Chart
Mode Tip Ring Sleeve
IR IR Out IR In Gnd
RS232 TxD RxD Gnd
Application Example
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
HDMI
CAT5e/6 or CAT6/STP
IR
Up to 250’ – with Key Digital
®
KD-CAT6STP1X
Up to 200’ – with CAT5e/6
Achieved Distance: up to 518’
6’
6’
6’
Up to 250’ – with Key Digital
®
KD-CAT6STP1X
CAT6/STP
CAT6/STP
CAT6/STP
CAT6/STP
HDMI
HDMI
HDMI
HDMI
HDMI
Display
Display
Blu-Ray
Blu-Ray
IR Emitter
IR
IR
KD-IRKIT300
IR Receiver
To control Blu-Ray
Daisy Chain Example:
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
KD-CATHD250Lite
HDMI
CAT5e/6 or CAT6/STP
IR
Up to 250’ – with Key Digital
®
KD-CAT6STP1X
Up to 200’ – with CAT5e/6
Achieved Distance: up to 518’
6’
6’
6’
Up to 250’ – with Key Digital
®
KD-CAT6STP1X
CAT6/STP
CAT6/STP
CAT6/STP
CAT6/STP
HDMI
HDMI
HDMI
HDMI
HDMI
Display
Display
Blu-Ray
Blu-Ray
IR Emitter
IR
IR
KD-IRKIT300
IR Receiver
To control Blu-Ray
Settings
Range and Resolution:
➔Using KD-CAT6STP1X Super CAT6 Shielded cabling:
All resolutions up to 1080p, 1920x1200, 3D up to 250 ft.; 4K up to 120’
➔Using Third-Party CAT5e/6 cabling: All resolutions up to 1080p, 1920x1200,
3D up to 200 ft.; 4K up to 120’
NOTE: Use metal shielded RJ45 connectors with soldered
ground wires when terminating the CAT6 STP.
Firmware Updates:
The KD-CATHD250Lite/POH Tx and Rx have an “Operation
Mode” switch. The 2 position slide switch is marked “Normal”
and “Program”. This switch should only be used in the
“Program” position when updating the unit’s firmware. Be sure
the switch is in the “Normal” mode for standard operation.
Forced HPD:
The KD-CATHD250Lite/KD-CATHD250POH baluns allow
modifying HPD (Hot Plug Detection) protocol between the source
and display. Modifying HPD protocol will allow overcoming HPD
handshake incompatibility between the source and display.
Modifying HPD protocol may also help fix other problems related
to HDMI connectivity.
KD-CATHD250Lite_POH_Manual.indd 4-5 9/6/13 12:12 PM

6 7
General
➔Regulation: CE, RoHS, WEEE
➔Enclosure: Black Metal
➔Product Dimensions (Each): L = 6” W = 4.1” H = 1.2”
➔Shipping Carton Dimensions: L = 7.48” W = 6.54” H = 5.2”
➔Product Weight (Each): 1 lb
➔Shipping Weight: 3 lbs
➔Power: UL Certified Power Supply – 5V / 2A, 110-240 VAC, 50-60 Hz
➔Power Consumption: Tx - 2.5 Watts, Rx - 5 Watts
Accessories
➔(2) 5V 2A DC Power Supply (KD-CATHD250Lite)
»KD-CATHD250Lite requires power on both Tx and Rx units
➔(1) 12V 2A (KD-CATHD250POH)
»KD-CATHD250POH only requires power on the Tx units,
which extends power to the Rx unit
➔(2) Mounting Brackets
➔(2) Locking HDMI Cable Clips
➔(1) Grounding Wire
Specifications
Technical:
➔Inputs Tx (Each): (1) HDMI, (1) 3.5mm Stereo (as either input or output)
➔Outputs Tx (Each): (1) CAT5e/6
➔Inputs Rx (Each): (1) CAT5e/6
➔Outputs Rx (Each): (1) HDMI, (1) 3.5mm Stereo (as either input or output)
➔HDMI
®
and HDCP Licensing: Fully licensed and compatible with all HDMI
and HDCP techologies
➔Link and Range: 1080p/60, 1920x1200, 1080i/60, 720p, 1080p/24;
up to 250 ft. when used with KD-CAT6STP1X cabling, up to 200 ft. when used
with CAT5e/6 cabling. 4K resolution up to 120’.
➔Lossless Compressed Digital Audio Support: Dolby
®
TrueHD, Dolby
®
Digital Plus
and DTS
™
-HD Master Audio
➔DDC Signal (Data): Input DDC Signal: 5 Volts p-p (TTL)
➔HDMI Video/Audio Signal: Input Video Signal: 1.2 Volts p-p
➔HDMI Connector: Type A, 19 Pin Female
➔RJ45 Connector: Shielded Link Connector
➔Control Extension Connector: 3.5mm Stereo Jack
➔I2C Communication: EDID and HDCP bi-directional transparency
from Display to Source
➔CEC Support: To the main input and output HDMI channel.
KD-CATHD250Lite_POH_Manual.indd 6-7 9/6/13 12:12 PM

8 9
How to Contact Key Digital
System Design Group (SDG)
For system design questions please contact us at:
»Phone: [phone]
»E-mail: [email protected]
Customer Support
For customer support questions please contact us at:
»Phone: [phone]
»E-mail: [email protected]
Technical Support
For technical questions about using Key Digital® products, please contact us at:
»Phone: [phone]
»E-mail: [email protected]
Repairs and Warranty Service
Should your product require warranty service or repair, please obtain a Key Digital®
Return Material Authorization (RMA) number by contacting us at:
»Phone: [phone]
»E-mail: [email protected]
Feedback
Please email any comments/questions about the manual to:
»E-mail: [email protected]
Warranty
All Key Digital
®
products are built to high manufacturing standards and should
provide years of trouble-free operation. They are backed by a limited two-year parts
and labor warranty.
Important Product Warnings
1. Connect all cables before providing power to the unit.
2. Test for proper operation before securing unit behind walls or in hard to access
spaces.
3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper
screw support with bolts or sheet-rock anchors.
Safety Instructions
Please be sure to follow these instructions for safe operation of your unit.
1. Read and follow all instructions.
2. Heed all warnings.
4. Do not use this device near water.
5. Clean only with dry cloth.
6. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
8. Only use attachments/accessories specified by the manufacturer.
9. Refer all servicing to qualified service personnel. Servicing is required when the
device has been damaged in any way including:
»Damage to the power supply or power plug
»Exposure to rain or moisture
Power Supply Use
You MUST use the Power Supply provided with your unit or you VOID the
Key Digital
®
Warranty and risk damage to your unit and associated
equipment.
KD-CATHD250Lite_POH_Manual.indd 8-9 9/6/13 12:12 PM