Key Digital FatCAT Rx KD-4AUVRX User manual

KD-4AUVRX & KD-4PUV are multi-channel video hubs that allow for the
transmission or reception of Color or Black & White single-channel video signals
up to 4,000 feet (KD-4AUVRX) or 2,600 feet (KD-4PUV) with standard, unshielded
CAT5 cabling.
KD-4PUV
Four Channel Passive Video
Transceiver
KD-4AUVRX
Four Channel Active Video
Receiver
4 Channel Security Hubs
Operating Instructions

Page 2
Please read all instructions to insure safe operation of the product.
Table of Contents
KD-4AUVRX
About KD-4AUVRX ................................................2
Installation and Operation............................................2
Video Connections ..............................................2
Power Connections .............................................2
Uses with Active Transmitters ......................................3
Uses with Passive Transceivers & Multi-Channel Receivers / Transceivers .....3
Distance Adjustment Settings ........................................3
Mechanical / Technical Specifications ..................................5
KD-4PUV
About KD-4PUV ..................................................2
Installation and Operation............................................2
Video Connections ..............................................2
Uses with Passive Multi-Channel Receivers ..........................3
Uses with Active Receivers & Active Multi-Channel Receivers . . . . . . . . . . . . . . 3
Distance Adjustment Settings ........................................3
Mechanical / Technical Specifications ..................................5
Key Digital
®
Security Products Compatibility Chart .........................4
Important Product Warnings .........................................6
Safety Instructions .................................................6
How to Contact Key Digital ..........................................7
Warranty ........................................................8

Page 1
Quick Setup Guide
Step 1: Begin with all input/output devices turned off with power cables removed
Step 2: Connect video source, CAT5/6/7 cabling, and Power into Active or Passive
Transmitter Baluns
Step 3: Insert twisted pair wires into “UTP In” Phoenix Connector or “UTP In”
CAT5/6/7 RJ45 connector as instructed on chassis above RJ45 input.
See “Video Connections” section.
Step 4: Connect video display and/or DVR to “Video Out” of KD-4AUVRX
Receiver Hub
Step 5: Secure + and – power wires into Phoenix Connector “Power” inputs
Step 6: Make appropriate settings to “Distance Adjustment” dip switches. See
“Distance Adjustment Table” section
Step 7: Power on all input/output devices
CAT5/6/7
Video
4,000’
CAT5/6/7
Video
4,000’
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
Video
Video Video
Video
Video Video
Video Video
Video Video Video Video
CAT5/6/7
Video Video
Video
Video
Video Video
Video
Video
Monitor
DVR
Monitor
DVR DVR
Monitor Monitor
DVR
Monitor
DVR
Monitor
DVR DVR
Monitor Monitor
DVR
CAT5/6/7
KD-AUVTX
KD-4AUVRX
KD-AUVTX KD-AUVTX KD-AUVTX
KD-4AUVRX
KD-4PUV
Security Cam Security Cam Security Cam Security Cam
Security Cam Security Cam Security Cam Security Cam
KD-4AUVRX
Four Channel Active Video
Receiver

Page 2
About KD-4AUVRX
➔Receives real-time Color or Black & White video
➔KD-AUVTX Extends video up to 4,000 ft using a standard CAT cable when used
with an Active Transmitter (Key Digital Model KD-AUVTX).
➔KD-4AUVRX extends video up to 2,600 ft when used with a Passive Transmitter
Balun (Key Digital Models KD-PVB and KD-4PUV)
➔Manual Distance Adjustment switches for optimum picture quality at any length
run up to 4,000 ft.
➔Built-in interference rejection enables wire bundling with other low-voltage lines
➔Built-in surge protection, ground loop isolation, gain and loss control, and video
detection
➔Compatible with CAT5/CAT5e/CAT6/CAT7 cabling
➔Works with generic power supplies, from DC/AC 9V to 12 V (not included)
Installation and Operation
Before permanently securing the unit for final installation of
cabling behind walls or ceilings, test for proper operation of the
unit and the cables in your system.
Video Connections
➔KD-4AUVRX features two input options for video reception; a RJ45 port labeled
“UTP In” and a Phoenix Connector labeled “UTP In”. It is recommended that only
one of the two options be utilized as the CAT5/6/7 input.
»Phoenix Connector: Secure twisted pair wires into “Video
+” and “Video -” of Phoenix Connector block by loosening
screws, inserting twisted pairs, and tightening screws until
connection is secured. If using shielded CAT cabling, you
may insert shield into Pin 3 of Phoenix Connector.
»RJ45: Terminate the incoming CAT5/6/7 twisted pair wires
into your RJ45 connector in the following fashion:

Page 3
Pin Assignment for KD-4AUVRX
Pin# 1 2 3 4 5 6 7 8
Description Pair 1
+
Pair 1
-
Pair 2
+
Pair 3
+
Pair 3
-
Pair 2
-
Pair 4
+
Pair 4
-
Power Connections
➔Secure + and – power wires into “Power” inputs (Pin 1 and Pin 2) of Phoenix
Connector in the same fashion as securing Video connections. Positive (+) and
Negative (-) polarity can be inserted into any of the two “Power” inputs. Insert
Ground wire into Pin 3 if desired.
Uses with Active Transmitters
➔KD-4AUVRX units can be coupled with Key Digital’s KD-AUVTX Active Video
Transmitter as part of a multi-camera CCTV system. Using the KD-4AUVRX with
the KD-AUVTX Active Hub will provide quality video up to 4,000 ft.
Uses with Passive Transceivers & Passive Multi-Channel Transceivers
➔KD-AUVRX units can be coupled with a passive Transmitter/Transceiver (Key
Digital model KD-PVB) or a passive Multi-Channel Transmitter/Transceiver (Key
Digital model KD-4PUV) in your application. Coupling a Passive Transmitter/
Transceiver with the KD-AUVRX Active Receiver Balun will provide quality video
up to 2,600 ft.

Page 4
Distance Adjustment Settings
Dip Switch Configurations:
Configuration Distance
1111 1’-150’
0111 150’ – 800’
0100 800’ – 1300’
0010 1300’ – 2000’
1110 2000’ – 4000’
➔Adjustments should be set identically on Transmit (KD-AUVTX) and Receiver
(KD-4AUVRX) unit.
➔All distances listed above correspond to the pairing of active Transmit Balun
(KD-AUVTX) and Active Receive Balun (KD-4AUVRX).
CAT5/6/7
Video
4,000’
CAT5/6/7
Video
4,000’
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
Video
Video Video
Video
Video Video
Video Video
Video Video Video Video
CAT5/6/7
Video Video
Video
Video
Video Video
Video
Video
Monitor
DVR
Monitor
DVR DVR
Monitor Monitor
DVR
Monitor
DVR
Monitor
DVR DVR
Monitor Monitor
DVR
CAT5/6/7
KD-AUVTX
KD-4AUVRX
KD-AUVTX KD-AUVTX KD-AUVTX
KD-4AUVRX
KD-4PUV
Security Cam Security Cam Security Cam Security Cam
Security Cam Security Cam Security Cam Security Cam

Page 5
Mechanical / Technical Specifications
Input 4 twisted pair from CAT5 line In on Phoenix type
stripping and cramping connector or 1 CAT5 on
RJ45 Connector
Output 2BNC connector for Composite Video 1Vpp with
75Ωat display side or Audio SPDIF or any other
format of video, audio, RS-232 or IR signaling.
Max. Signal Input /
Output Level:
Composite: 1.2Vpp on 75Ωterminated at display, DC
coupling or Line Audio or TTL +5V for digital RS-232,
IR signaling
Surge Protection Renewable solid state surge protection.
Bandwidth DC to 6 MHz
Video Format NTSC, PAL, SECAM
Impedance BNC side 75Ωunbalanced,
UTP side 100Ωbalanced
Humidity 0% to 95% non condensing
Distance 4000 feet Active Tx with Active Rx Coupling,
2000 feet Passive Tx with Active Rx coupling
Equalization and Gain
Adjustments
Passive impedance matching and fixed equalization.
Manual adjustment by dip switches for CAT5 cable
length measurement up to 4000 ft
Video S/N Ratio: 58 dB RMS un-weighted;
65 dB RMS @5MHz weighted
Ground Isolation Ground connection available for STP or Ground
loop removal
Power Source: DC/AC 9-12V
Dimensions: WxDxH: 7.5”x3.3”x 1.75” excluding BNC
Weight: 2 lb
Operating Temperature -14F to +120F
Accessories: None

Page 6
Quick Setup Guide
Step 1: Begin with all input/output devices turned off with power cables removed.
Step 2: Connect video source and CAT5/6/7 cabling to Transmitter/Receiver Baluns
Step 3: Insert twisted pair wires into “UTP In” Phoenix Connector or “UTP In”
CAT5/6/7 RJ45 connector as instructed on chassis above RJ45 input.
See “Video Connections” section.
Step 4: Connect video source, display and/or DVR to “Video Out” of KD-4PUV
Transceiver Hub
Step 5: Power on all input/output devices.
KD-4PUV
Four Channel Passive Video
Transceiver
CAT5/6/7
Video
1,300’
CAT5/6/7
Video
1,300’
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
Video Video
Video Video
Video Video Video Video
CAT5/6/7
Video
Video Video Video
Monitor Monitor Monitor Monitor
Monitor Monitor Monitor Monitor
CAT5/6/7
KD-4PUV
KD-4PUV
KD-4PUV
KD-PVB KD-PVB KD-PVB KD-PVB
Security Cam Security Cam Security Cam Security Cam
Security Cam Security Cam Security Cam Security Cam

Page 7
About KD-4PUV
➔Transmits or Receives real-time Color or Black & White video
➔Extends Black & White video up to 2,600 ft using a standard CAT cable when
used with an Active Receiver (Key Digital models KD-AUVRX or KD-4AUVRX).
➔Extends Black & White video up to 1,300 ft using a standard CAT cable when
paired with a Passive Transmitter Balun (Key Digital models KD-PVB or KD-4PUV).
➔Built-in interference rejection enables wire bundling with other low-voltage lines
➔Compatible with CAT5/CAT5e/CAT6/CAT7 cabling
Installation and Operation
Before permanently securing the unit for final installation of
cabling behind walls or ceilings, test for proper operation of the
unit and the cables in your system.
Video Connections
➔KD-4PUV features two options for video reception; a RJ45 port labeled “UTP In”
and a Phoenix Connector labeled “UTP In”. It is recommended that only one of the
two options be utilized as the CAT5/6/7.
»Phoenix Connector: Secure twisted pair wires into “Video
+” and “Video -” of Phoenix Connector block by loosening
screws, inserting twisted pairs, and tightening screws until
connection is secured. If using shielded CAT cabling, you
may insert shield into Pin 3 of Phoenix Connector.
»RJ45: Terminate the incoming CAT5/6/7 twisted pair wires
into your RJ45 connector in the following fashion:
Pin Assignment for KD-4AUVRX
Pin# 1 2 3 4 5 6 7 8
Description Pair 1
+
Pair 1
-
Pair 2
+
Pair 3
+
Pair 3
-
Pair 2
-
Pair 4
+
Pair 4
-

Page 8
Uses with Passive Multi-Channel Receivers
➔KD-4PUV units can be paired with additional KD-4PUV 4-Channel Passive Video
Receiver Hubs as part of a multi-camera CCTV system. Using the KD-4PUV with
the KD-4PUV Passive Hub will provide equivalent distances as when coupled with
other Key Digital Passive Transceiver Baluns; 1,300 feet.
Uses with Active Receivers & Active Multi-Channel Receivers
➔KD-4PUV units can be used as a Transmitter and coupled with an Active Receiver
(Key Digital model KD-AUVRX) or an Active Multi-Channel Receiver (Key Digital
model KD-4AUVRX). Coupling a KD-4PUV 4-Channel Passive Transmitter with
the KD-AUVRX Active Receiver Balun or KD-4AUVRX Active 4-Channel Receiver
will provide quality video up to 2,600 ft.
Note: The usage of a KD-4PUV balun to receive video signals from an Active Transmitter
(Key Digital model KD-AUVTX) is not recommended. For best results in an active/passive
coupling, it is recommended that the KD-4PUV Passive Video Balun be used as the
Transmitter, while the KD-AUVRX or KD-4AUVRX Active Video Receiver Baluns be used as
the Receiver.
CAT5/6/7
Video
1,300’
CAT5/6/7
Video
1,300’
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
CAT5/6/7
Video
Video Video
Video Video
Video Video Video Video
CAT5/6/7
Video
Video Video Video
Monitor Monitor Monitor Monitor
Monitor Monitor Monitor Monitor
CAT5/6/7
KD-4PUV
KD-4PUV
KD-4PUV
KD-PVB KD-PVB KD-PVB KD-PVB
Security Cam Security Cam Security Cam Security Cam
Security Cam Security Cam Security Cam Security Cam