Keysight Technologies N9020B Manual

Option CR3, Second IF Out
or
Option CRP, Arbitrary IF Out
Keysight Technologies
N9020B MXA Signal Analyzer
N9010B EXA Signal Analyzer
N9048B PXE EMI Receiver
Installation Note

Notices
© Copyright 2016 - 2018 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9020-90258
Edition
Edition 1, October 2018
Supersedes February 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403

Installation Note N9020-90258 3
Option CR3 or CRP Installation Kit
Option CR3 or CRP Installation Kit
Products Affected: N9020B MXA Signal Analyzer
N9010B EXA Signal Analyzer
N9048B PXE EMI Receiver
Serial Numbers: All
Options
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
(X) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time:
0.5 Hours
0.5 Hours

4Installation Note N9020-90258
Option CR3 or CRP Installation Kit
Introduction
This kit contains all of the instructions required to install Option CR3 or CRP on a Keysight MXA or
EXA signal analyzer or PXE EMI receiver that already has the necessary hardware installed. If the
necessary hardware is not already installed, a different upgrade kit should be used.
To install this kit, the analyzer must already have both of the following:
— A rear panel AUX IF OUT port
— A compatible Front End Controller assembly installed.
Some analyzers will have an AUX if OUT port, but will not have a compatible Front End Controller
assembly.
To verify if a compatible Front End Controller assembly is installed, press System, Show Hardware.
Refer to the row for the Front End Controller and note the Hw Id entry.
If the Front End Controller’s Hw Id is 41 or 75, you may proceed with the installation of this kit.
If the option being installed is Option CRP and the Front End Controller’s Hw Id is not either 41 or
75, do not install this kit. Instead, install the N9010BU-HL3 kit or N9020BU-HL3, as appropriate.
If the option being installed is Option CR3 and the Front End Controller Hw Id is either 41, 75, or
170, you may proceed with the installation of this kit.
If the option being installed is Option CR3 and the Front End Controller Hw Id is not either 41, 75, or
170, do not install this kit. Instead, install the N9010BU-HL3 kit or N9020BU-HL3 kit, as
appropriate.
1. At the time of manufacture the hardware related to this option was fully
adjusted and the option performance was verified to be within its warranted
specifications. Within one year of the initial calibration date of the instrument
this option is fully calibrated with no further adjustment or verification testing.
To determine the initial calibration date, locate the original calibration
certificate that was shipped with the instrument at the time of purchase. The
Date of Calibration is printed on the original calibration certificate.
To ensure that this newly installed option has been installed properly, the
procedure that follows includes a functional check.
2. The latest revision of the X-Series Signal Analyzers software may be
downloaded from
http://www.keysight.com/find/xseries_software
If a software update is required, perform the software update BEFORE
following the procedure in this document for redeeming and installing the
option upgrade license key.
3. This option is licensed for one instrument model/serial number combination.
The license key will only install on the designated instrument.

Installation Note N9020-90258 5
Option CR3 or CRP Installation Kit
Contents
Tools Required for Installation
— Personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
Tools Required for Manual Operation Verification
— Spectrum Analyzer capable of measuring a 322.5 MHz signal at -40 dBm
— Test cable, sma or 3.5 mm connectors
— Adapters as needed to connect the cable between the spectrum analyzer and sma AUX IF OUT
port on the rear panel of the signal analyzer.
Installation Procedure over USB
1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an
attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File to the root directory of the USB storage device.
6. Connect the USB storage device to the signal analyzer USB port. Windows will detect the new
hardware and may display the configuration menu shown in Figure 1. This menu may be
configured according to your preferences.
Quantity Description Keysight Part
Number
1 Installation Note This note
1 Option Upgrade Entitlement Certificate 5964-5178

6Installation Note N9020-90258
Option CR3 or CRP Installation Kit
Figure 1 USB Storage Device Configuration Menu
7. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message similar to the one shown in Figure 2.
Figure 2 Successful License Installation
Alternate Installation Procedure
The License File can be manually installed over USB or LAN by placing the license file in the
following folder on the signal analyzer
C:\Program Files\Agilent\licensing
Verify the Installation
1. Cycle the power on the signal analyzer.
2. Press System, Show System to display a list of installed options.
3. Verify that the newly installed option appears on the list.

Installation Note N9020-90258 7
Option CR3 or CRP Installation Kit
Functional Check:
Within one year of the initial calibration date of the instrument this option is fully calibrated with no
further adjustment or verification testing. To ensure that this newly installed option has been
enabled correctly the following functional check is recommended.
1. Tap the message balloon at the bottom of the main display. This will remove out-of-date
errors. Tap Xto close the error history window.
2. Press System, Alignments, Align Now, All. Tap Xto close the align now window.
3. Watch for any errors during the instrument alignment.
4. Tap the message balloon at the bottom of the main display to view the instrument error log.
5. Verify that there were no errors during the alignment. Tap Xto close the error history window.

8Installation Note N9020-90258
Option CR3 or CRP Installation Kit
Manually verify operation
Option CR3, Second IF Output
1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.
2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,
key in 50 MHz. Tap Span, Zero Span. You should see a flat line across the display at -25 dBm.
3. Enable Option CR3. Press Input/Output, Output, Aux IF Out, Second IF Out.
4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate
adapters.
Spectrum analyzer settings:
Center frequency: 322.5 MHz
Span: 1 MHz
Bandwidth: 100 kHz
The spectrum analyzer should display a −33 dBm ±5 dB signal
Option CRP, Arbitrary IF Output
1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.
2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,
key in 50 MHz. Tap Span, Zero Span. You should see a flat line across the display at -25 dBm.
3. Enable Option CRP. Press Input/Output, More, Output, Aux IF Out, Arbitrary IF. Tap Arbitrary IF
Freq. Set the Arbitrary IF Out frequency to 70 MHz.
4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate
adapters.
Spectrum analyzer settings:
Center frequency: 70 MHz
Span: 1 MHz
Bandwidth: 100 kHz
The spectrum analyzer should display a −33 dBm ±5 dB signal

Installation Note N9020-90258 9
Option CR3 or CRP Installation Kit
Utilities, Adjustments, and Performance Verification Tests
Calibration Software and specified test equipment is required to perform the adjustments, and can
be used to automate the performance verification testing. Information on how to obtain this
software can be found at
http://www.keysight.com/find/calibrationsoftware
Utilities Required
None
Adjustments Required
None
Performance Testing Required
None
A full calibration is required to assure the instrument meets all specifications
The end user must ultimately determine whether they want a full calibration to be performed after
the installation of this upgrade or not. If a full calibration is required, arrangements regarding the
level of calibration must be made between the end user and the calibration provider.
For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your
local Keysight office access the following URL, or if in the United States, call the following
telephone number:
http://www.keysight.com/find/assist
1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change
without notice.
© Keysight Technologies 2016-2018
Edition 1, October 2018
N9020-90258
www.keysight.com