Keysight Technologies UXA Installation and operation manual

Option FT1 and FT2 -
Frequency Mask Trigger
Keysight UXA
Signal Analyzers
Installation Note

Notices
© Copyright 2016 - 2017 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9040-90027
Edition
Edition 1, June 2017
Supersedes February 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403

Installation Note N9040-90027 3
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
Introduction
This kit contains the instructions to install either Option FT1 or Option FT2 on a Keysight UXA
Signal Analyzer. FT1 or FT2 is supported by the N9067C Pulse application and the 89600 VSA
application.
Products Affected: N9040B UXA Signal Analyzer
N9041B UXA Signal Analyzer
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
(X) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time:
0.5 Hours
0. Hours
1. The signal analyzer being upgraded must have one of the wide
bandwidth options listed below already installed. To verify that one of
these options is present, press System, Show System, and look under
"Options" for the presence of the options listed.
—Must have N9040B-B2X, or N9040B-B5X, or N9041B-H1G
2. This option is licensed for one instrument model/serial number
combination. The license key will only install on the designated
instrument.

4Installation Note N9040-90027
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
Contents
Tools Required
— Personal computer with internet access and USB port
— USB storage device with >2GB free memory
Quantity Description Keysight Part Number
1 Installation Note This note
1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9040-90027 5
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
Installation Procedure
License Installation Over USB
1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an
attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File to the root directory of the USB Storage Device.
6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new
hardware and may display the configuration menu shown in Figure 1. This menu may be
configured according to your preferences.
Figure 1 USB Storage Device Configuration Menu

6Installation Note N9040-90027
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
7. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message similar to the one shown in Figure 2.
Figure 2 Successful License Installation
Alternate Installation Procedure
The License File can be manually installed over USB or LAN by placing the license file in the
following folder on the signal analyzer
C:\Program Files\Agilent\licensing
Verify the License Installation and Instrument Software Version
1. Cycle power on the signal analyzer.
2. Press System, Show System to display a list of installed options.
3. Verify that the newly installed option number (N904xB-FT1 or N904xB-FT2) appears on the
list.

Installation Note N9040-90027 7
Option FT1 and FT2 - Frequency Mask Trigger Installation Kit
Utilities, Adjustments, and Performance Verification Tests
Utilities Required
None
Adjustments Required
None
Performance Testing Required
None
For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your
local Keysight office access the following URL, or if in the United States, call the following
telephone number:
http://www.keysight.com/find/assist
1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change
without notice.
© Keysight Technologies 2016-2017
Edition 1, June 2017
N9040-90027
www.keysight.com