
Multisource Signal Controller
PATENT PENDING
SAT CATV
ROOFTOP
SAT PREP
TO WATCH OVER-THE-AIR TELEVISION
(1)Connect television to the “CATV/ANT” port
on the wall plate with a coaxial cable.
(2)Turn TV on.
(3)For most television sets, go to the menu,
select antenna (usually “ANT”) input and run
auto-program to program viewable channels.
TO WATCH CABLE TELEVISION
(1)Connect Cable TV service to the KeyTV Multisource Signal Controller’s “CATV” port.
(Located on your vehicle’s exterior.)
(2)Connect television to the “CATV/ANT” port on the wall plate with a coaxial cable.
(3)Turn your TV on. For most television sets, go to the menu, select cable (usually “CATV”) input and
run auto-program to program viewable channels.
TO WATCH SATELLITE TELEVISION
(1)Connect coaxial wire from the satellite dish’s main port to the KeyTV Multisource Signal
Controller’s “SAT” port. (Located on your vehicle’s exterior.) Most portable systems require this
coaxial wire to be 25 ft. or less for proper satellite operation.
•Please refer to your satellite equipment product manual for satellite receiver and television set up.
(2)At the television monitor, connect satellite receiver to the “SAT” port on the wall plate with a
coaxial cable. Then, connect receiver to the television with an HDMI cable.
ROOF MOUNT SATELLITE PREP
Just plug and play.
CATV/ANT
SAT
KeyTV
Multisource Signal Controller
POWER
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
KeyTV
Multisource Signal Controller
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
CATV/ANT
SAT
KeyTV
Multisource Signal Controller
POWER
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
KeyTV
Multisource Signal Controller
PATENT PENDING
SAT CATV
CATV/ANT
SAT
CATV/ANT
SAT
Antenna
Auto Program
Cable
Air
CATV/ANT
SAT
KeyTV
Multisource Signal Controller
POWER
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
KeyTV
Multisource Signal Controller
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
CATV/ANT
SAT
CATV/ANT
SAT
KeyTV
Multisource Signal Controller
POWER
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
KeyTV
Multisource Signal Controller
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
CATV/ANT
SAT
Note: To watch over-the-air channels, make sure that cable service is not con-
nected to the KeyTV Multisource Signal Controller.
Note: If cable service is weak or compromised (-50 dBm or stronger required), KeyTV will automatically switch
your feed to the over-the-air channels. For over-the-air viewing, disconnect cable from the exterior KeyTV
signal controller.
Note: With portable systems, you will be able to watch satellite program on any one television. Compatibility diagrams are
available from Keystone Customer Service.
1
3
3
12
12
CATV/ANT
SAT
KeyTV
Multisource Signal Controller
POWER
PATENT PENDING
SAT CATV
Antenna
Auto Program
Cable
Air
KeyTV
Multisource Signal Controller
PATENT PENDING
SAT CATV
CATV/ANT
SAT
CATV/ANT
SAT
Antenna
Auto Program
Cable
Air
ANT FM TV-1 TV-2 TV-3 TV-4
BLACK
PURPLE
GRAY
TAN
WHITE
ORANGE
BLUE
ANTENNA
RADIO FM
BEDROOM TV
MAIN LIVING TV
BEDROOM 2 TV / GARAGE TV
OUTSIDE / CARGO TV
ROOFTOP SATELLITE PREP
KEYSTONE’S EXCLUSIVE COLOR-CODED WIRING STANDARD FOR KeyTV
Each monitor’s wall plate connects directly to the KeyTV Multisource Signal Controller
with a color-coded coaxial cable. Should an issue arise, check to make sure the
connection is tight at the wall plate and at the corresponding connection on your
KeyTV unit. If further service is required, the color-coded cables make it easy to locate
and correct any issues.
Applications with 5 TV locations require the replacement of the factory installed
splitter located between TV 4 & TV 5 with an approved satellite providers splitter.
Many Keystone RV models feature an exclusive
satellite pass-through on the Winegard Air 360+
antenna.
(1)Connect roof-mounted satellite receiver to
the port on the side of your RV’s antenna.
(2)Next to the KeyTV controller, there is a blue
“rooftop satellite prep” cover. Remove this cover
to connect the satellite feed cable to the “SAT”
input on the controller.