Kicker 46HDS962 User manual

GETTING STARTED
1. Protect all painted surfaces and passing lamps, if equipped, with a soft cloth.
2. Remove seat and disconnect negative battery terminal. (Fig. 1)
a. On 2009 and later models it will help to remove the two T40 bolts and the ECM and tray. (Fig. 2)
3. Remove windshield and outer fairing.
a. Remove the three windshield fasteners. (Fig. 3)
b. Remove the four T27 fairing fasteners and disconnect the headlamp. (There are two as shown in Fig. 4 and two located between
the fork and the frame)
SPEAKER REMOVAL/ INSTALLATION
4. Unplug both terminals on the left and right speakers. (Fig. 5)
5. Remove the three T25 fasteners that secure eachspeaker to the inner fairing.
6. If using the KICKER grilles, peel the stock speaker grilles off of the speaker stand-off (Fig. 6)
7. Separate the speaker from the stand-off, it’s a snap fit (Fig. 7)
8. Insert your KICKER speaker into the stand-off, making sure the terminals are on the top side
9. Now is the time to install your KICKER emblems into the KICKER grilles, if using
a. Place emblem into grille and bend tabs over
10. Lay the grille over the speaker and refasten the speaker to the inner fairing using the hardware removed in step 2.
AMP INSTALLATION
11. Disconnect the radio harness and antenna from the radio. (Fig. 8)
12. Remove the two T20 fasteners at the top of the radio chassis. (Fig. 8)
a. If using on a radio with CB and/or XM modules, remove the modules from the radio at this time.
13. Fasten the amplifier to the bracket using supplied hardware and orient with connector to the clutch side of the motorcycle. (Fig. 9)
14. Making sure all wiring is safely out of the way, slide the amp bracket over the radio chassis and engage tabs on amp bracket into the
rubber grommets on the radio. (Fig. 10)
15. Reinstall the T20 fasteners, removed in step 2, through the amp bracket and into the radio. (Fig. 10)
16. To reinstall modules, slide them under the radio chassis and fasten to the tabs on the amplifier bracket with supplied hardware.
WIRE ROUTING
17. Take the electrical harness and plug it into the amplifier.
18. Following the color code, route the left and right side speaker wires safely to their respective speakers. (Fig. 11)
19. Plug in the male ends into the stock harness, the terminals removed during speaker installation. (Fig. 11)
20. Plug the female ends onto the speaker terminals. (Fig. 11)
21. Locate the headlamp harness and remove the red cap over the Orange/White wire. If the Orange/White wire is currently in use (e.g.
accessory lighting) unplug and connect to one of the blue wires from the KICKER harness. Plug the other blue wire from the KICKER harness
into the Orange/White wire, making sure it is fully engaged. (Fig. 12)
22. Whether the extra blue wire lead is being used or not, heat shrink has been provided to put over it to reduce the risk of a short. (Fig. 15)
23. Follow the proper procedure to remove the fuel tank.
24. Remove the electrical caddy lid.
25. Route the power harness on the clutch side of the frame neck, lay it into that caddy and under the seat. (Fig. 14 & 15)
a. You may want to remove the fuse now while figuring out wire placement.
26. The blue lead under the seat would be used if installing a second amplifier, but again, whether used or not, cover with heat shrink to
reduce the risk of a short. (Fig. 15)
46HDS962
Motorcycle Audio Kit Installation Guide for Harley Davidson®
Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes
1996–2013 (FLHT)
Package Contents:
(1) Install Guide (1) Wiring Harness (4) Black Cable Ties
(2) 5-1/4” KICKER Speakers (6) 8-32 x 1/2” Button Head Bolts (1) Amp Mounting Bracket
(1) 200W KICKER Amp (6) 8-32 Nylock Nuts (4) Black Heat Shrink
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifications. KICKER is not responsible for damage resulting from improper installation techniques. This kit may not
be compatible with some aftermarket head units.

SYSTEM SETUP
Note: KICKER recommends that the dip switches be set up as follows:
Auto turn-on - 12VInput level - HIHI-PASS – 80 Hz Input Gain control – 0
27. Connect the battery terminals, install fuse, check audio system operation and set gain to optimize system performance.
28. Be sure to check that none of the wires will be in a bind when the steering head is turned fully to the right or the left.
29. Disconnect negative battery terminal and carefully reassemble motorcycle.
30. Reconnect negative battery terminal, install seat and enjoy your KICKER audio system!
For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am – 5:00 pm CST or email at [e-mail].
For installation videos please go to our KICKER YouTube channel.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDS962-C-20200228
123 4
5 6 7 8
910 11 12
13 14 15

lfKICKER
PS COAXIAL SPEAKERS
Owner's Manual
Authorized KICKER Dealer:
Purchase Date:
PERFORMANCE
WooferSize
Tweeter Size
Frequency Response
MaxAmplifier Power
Sensitivity [1 W/1 m]
Nominal Impedance
Weight
5-1/4" [133mm]
3/4" [20mm]
60Hz-20kHz
1 OOW PEAK I 50W RMS
88.3d8
2 O(PS5250), 4 O(PS52504)
12.6oz [358g]
Mounting Hole Diameter 4-7 /8" [124mm]
Mounting Depth 2-3/16" [56mm]
[4 7/8"]
124mm
[2 3/16"] 1
56mm --1
[9/16"]
14mm
2 0 PS5250 2006-2013 Harley-Davidson® with premium audio system and similar touring bikes
4 0 PS52504 1998-2005 Harley-Davidson with premium audio system [Road Glide may require Harley-
Davidsonparts 77021-98B and 77022-98B]
2008-present Victory
Please refer to your bike's factory service manual for dissassembly/installation information. Typically, you should
retain all factory screws, hardware, and grilles when upgrading your bike to a KICKER system. The following
diagrams show how to install the PS5250 speakers in a Harley-Davidson bike with "batwing" style fairing
(2006-2013). Note: Do not install in systems that are not 2-ohm stable!
1. Remove front side of fairing.
• 7xTorxT25 ®
@)-
2
PS COAXIALS

2. Remove factory speakers.
Remove the factory speakerconnectors.
Retain the 3 factory screws.
Remove the factory speakers from the factory angle mount (be careful not t~ damage the angle mount).
[ viewed from front of bikeJ
factory speaker location
factory speaker connectors
3. Prepare PS5250 for installation.
Install the KICKER badges onto the grilles; bend the rear pests to secure them 1n place.
For Harley "batw1ng" installations, replace the factory grilles with KICKER grilles. factory screws x 3
KICKER PS525~ ~
For all other Harley applications, use the factory grilles only.
recommended
badge location
factory grille
(remove for "batwing" only)
4. Install PS5250 in factory location.
Use the 3 factory screws.
Connect the factory speakerconnectors to the PS5250 terminals.
Re-install your bike's front fairing in the reverse orderyou disassembled it.
install short screw at
bottom
3

ACOUSTICS LIMITED WARRANTY
When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material and
workmanship under normal use for a period of ONE (1) YEAR from date of original purchase. If this product is identified
as "Refurbished" or "B Goods", the wa,anty is limited to a period of THREE (3) MONTHS from date of original purchase.
In all cases you must have the original receipt. Should service be necessaryunder this warranty for any reason due to
manufacturing defector malfunction du~ng the warranty period, KICKER will repair or replace (at its discretion) the defective
merchandise with equivalent merchandse. Warranty replacements may have cosmetic scratches and blemishes. Discontinued
products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is
not extended to owners ofthe product subsequent to the original purchaser. Any applicable implied warranties are limited in
duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and
no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied
warranties; therefore, these exclusions may not apply to you. This warranty gives you specific legal rights; however you may
have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or bycontacting Stillwater Designs
directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at [phone]for a Return Merchandise Authorization (RMA) number. Package only
the defective items 1n a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective products. The
return of functioning items increases your return freight charges. Non-defective items wll be returned freightcollect to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
ofthe original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing the Customer's
name, Dealer's name and invoice number, and product purchased. Warranty expiration on items without proof-of-
purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the produ8t is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to othercomponents
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization (RMA) number
o Products purchased from an UNAUTHORIZED dealer
o Freight Damage
0 The cost of shipping product to KICKER 5) stillwaterdesigns
o Service performed by anyone other than KICKER
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one-week service for all acoustics (subwoofers, midrange drivers, tweeters,
crossovers, etc) returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to
follow these steps may void your warranty. Any questions can be directed to the KICKER Customer Service Department
at [phone]. Contact your International KICKER dealer ordistributor concerning specific procedures for your
country's warranty policies.
Note : All specifications and performance figures are subject tochange. Please visit www.kicker.com for the most
current information.
P.O. Box 459 • Stillwater, Oklahoma 74076 •USA • [phone]
10PS52504-B-20151022
10
PS COAXIALS

INTERNATIONAL WARRANTY
Contact your International KICKER dealer or distributor concerning
specific procedures for your country's warranty Policies.
WAR NING: KICKER products are capable of producing sound levels
tha t can permanently damage your hearing! Turning upa system to a
level that has audible distortion is more damaging to your ears than
listening to an undistorted system at the same volume level. The
threshold of pain is always an indicator that the sound level is too loud
and may permanently damage your hearing. Please use common
sense when controlling vol u me.
GARANTIA INT ERNAC I ONAL Version Espanol
Our goods cormwith guarant('As that rnnnot be
excluded under the Australian Consumer Law
You are entitled to a roplacerr-ent or refund tor a
major failure and for c.;om!)tlf ,sat,on for any Ottltlr
reasonably foreseeable loss or damage . You are also
entitled to have the goods repaired or replaced rt the
goods fail to be of acceptable qw1hty and the failure
does not amount tr. a major faih ,re
Cornuniquese con su conces1onario o distribuidor KICKER internacional para obtener infor aci6n sob re procedi m1entos especificos
relacionados con las normas de garantfa de su pais.
ADVERTENCIA. Los excitadores KICKER son capaces de producir niveles de sonido que pueden dai'lar permanenternente
el oido. Subir el volumen del s1sterna hasta un nivel que produzca distors16n es mas dai'lino para el ofdo que escuchar un
sistema sin distorsi6n al mismo volumen. El dolor es siempre una indicaci6n de que el sonido esmuy fuerte y que puede danar
permanentemente el ofdo. Sea precavido cuando controle el volumen.
La frase "combustible para vivir la vida Livin' Loud™ a todo volumen' se refiere al entusiasmo per la vida que la marca KICKER
de estereos de autom6vil representa y a la recomendaci6n a nuestros clientes de que vivan lo mejor posible ("a todo volumen')
en todo sentido. La linea de altavoces y amplificadores KICKER es la mejor de! mercado de audio de autom6viles y per lo tanto
representa el "combustible' paravivir a todo volumen en el area de "estereos de au tom6vil' de la vida de nuestros clientes.
Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos locales sobre ruido en cuanto a los
niveles legales y apr op1ados de audici6n fuera de! vehfculo.
INTER N ATIONALE GARANTIE
Deutsche Version
Nehmen Sie mit l hren intemationalen KICKER-Fachhandler oder Vertrieb Kontakt auf, um Details Ober die Garantieleistungen in
lhrem Land zu erfahren.
WARNUNG: KICKER-T reiber k6nnen einen Schalipegel erzeugen, de r zu permanenten Geh6rschaden !Ohren kann! Wenn Sie ein
System auf einen Pegel stelien, derh6rbare Verzerrungen erzeugt, schadet das lhren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstarkepegel. Die Schmerzschwelie ist immer e1 ne Anzeige dafOr, dass der Schalipegel zu laut istund zu
permanenten Geh6rschaden !Ohren kann. Seien Sie bei der Lau tstarkeeinst eliung bitte vernOnftig!
Der Slogan "Treibstoff !Or Li vin' Loud" bez 1eht sich aut die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen, in alien Aspekten ihres Lebens nach dem Besten ("Uvin ' Loud") zu streben. Die
Lautsprecher un d Verstarker von KICKER sind auf dem Markt !Or Auto-Soundsysteme fOhrend und st elien somit den "T reibstoff'
!Ordas Autostereoer1ebnis unserer Kunden dar. Wir empfehlen alien unseren Kunden, sich bezOg lich derzugelassenen und
passenden Lautstarkepegel auBerhalb des Autos an die 6rtlichen Larrnvorschriften zu halten.
GARA N TIE I NT ERN ATI ONA LE Version Frant;aise
Pour connaitre !es procedures propres a la pclitique de garantie de votre pays, contactez votre revendeur ou distributeur
lntemat1onal KICKER.
AVERTISSEMENT: Les haut-parleurs KICKER ont la capacite de produ1re des niveaux sonores pcuvant endommager l'ou'ie de
fa9on irreversible ! L'augmentation duvolume d'un systeme jusqu'a un niveau presentant une distorsion audible endommage
davantage l'ou'ie que l'ecouted'un systeme sans distorsion au meme volume. Le seuil de la douleur est toujours le signe que le
niveau sonore est trop eleve et risque d'endommager l'ou'ie de fa9on irreversible. Reglez le volume en faisant prevue de bon sens!
L'expression • carburant pcur vivre plein pct • fait refe rence au dynamisme de la marque KICKER d'equipements audio pcur
vehicules et a pcurbut d'encouragernos clients a faire le maximum(" vivre plein pct") dans tousles aspects de leur vie. Les
haut-parleurs et arnplificateurs KICKER sont !es meilleurs dans le domaine des equipements audio et representent done pcur nos
client le • carburant pour vivre plein pct •dans !'aspect • installation audio de vehicule " de leur vie. Nous encourageons tous nos
clients a respecter toutes les lois et reglementations locales relatives aux niveaux sonores acceptables a l' exterieur des vehicules.
11

Harley-Davidson is a registered trademark of Harley-Davidson, Inc.
Harley-Davidson es una marca registrada de Harley-Davidson, Inc.
Harley-Davidson ist ein eingetragenes Warenzeichen von Harley-Davidson, Inc.
Harley-Davidson est une marque deposee de Harley-Davidson, Inc.
©2009 Stillwater Designs

PXA Amplifiers
PXA STEREO AMPLIFIER
PXA200.2
Owner's Manual i English
Manual dei Prop1etano I Espanol
AMPLIFICADOR DEL LA SERIE PXA. 2
Benutzerhandbuch IDeutsch
MONOVERSTARKER DER PXA.2-SERIE
Manuel d'utilisation I Franc;a1se
AMPLIFICATEUR DE SER IE PXA.2

(fKICKER
MODEL:
Authonzed KICKER Dealer:
Purchase Date:
Serial Number:
PXA.2-SERIES AMPLIFIERS
OWNER'S MANUAL
PXA200.2
IMPORTANT SAFETY WARNING - PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER IN A
DISTORTED OR CLIPPED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING
FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE.
PERFORMANCE
Model:
RMS Power [Watts]
@ 14.4V, 40 stereo, :,; 1% THD+N
@ 14.4V, 20 stereo, s: 1% THD+N
@ 14.4V, 10 stereo, s: 1% THD+N
Length [in, cm]
Height [in, cm]
Width [in, cm]
Frequency Response [Hz]
Signal-to-Noise Ratio [dB]
Input Sensitivity
Electronic Crossover
PXA200.2
25 X 2
50 X 2
100X 2
7, 17.8
1-5/8, 4
3-7/16, 8.7
10 - 20k
95
Low Level: 125mV-5V
High Level. 250mV-1 0V
Selectable HI or OFF; 60Hz, 80Hz or 120Hz; 12dB/octave slope
Pro Tip: To get the best performance from your new KICKER Amplifier and extend the warranty by 1 year, use
genuine KI CKER accessories and wiring.
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifier. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4" (10cm) of open
ventilation for the amplifier. Drill four holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the
amplifier.
Wiring: Disconnect the vehicle's battery to avoid an electrical short. Then, connect the PXA harness to the
amplifier. A good ground connections is important. If this amplifier is mounted in the front fairing of a motorcycle, it
will be best to extend the ground wire all the way to the battery.
The PXA amplifiers have the capability to receive almost any level of input signal. If a Hi-Level signal is coming
from the speaker leads of the source unit, simply cut off the RCA jacks and connect it directly to the exposed
wires. Set the Input Level switch to Hi. Set the Auto Turn-On to DC. If speaker leads are not available from your
source unit, use an RCA stereo cable to connect directly to the RCA connectors of the PXA amplifier. Set the
Input Level switch to Lo. Set the Auto Tum-On switch to+ 12V, and use the blue remote trigger wire to tum the
amplifier on.
2

to amplifier
from source unit high-level speaker outputs
Model
PXA200.2
EJCtemal Fuse
1x 15 Ampere
Cut the looped red powercable located on the PXA harness and install a 15A fuse. Fuse installation should be
within 18" (45cm) of the battery and in-line with the harness' power cable, which is connected to your amplifier. If
you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the
last wire disconnected from the amplifier--just the opposite as when you installed it.
I ◄
-
-
-
~24"
(60cm)
► I
bare-metal chassis
ground
remote
tum-on
RCA inputs
(remove to use
hi - level input)
+
• L
-
--
speaker outputs
~ 18"
(45cm)
► I
-
battery -
-
-
bare-metal chassis ground
3

OPERATION
GAIN
'
~~ ~~ ~~ ~~
bd bd bd bd
60Hz BOHz 120Hz OFF
HI-PASS FILTER
LO 12V
~ ~
HI DC
L L AUTO TURN-ON
INPUT LEVEL
Automatic Turn-On Selection: The PXA series offers two automatic turn-on modes that can be selected on
the end panel; + 12V or DC Offset. Using the DC Offset mode causes the REM terminal wire to have+12V out
for turning on additional amplifiers.
• Remote Turn-On: Set the switch to + 12V to use the remote turn-on lead from the PXA harness. Run 18
gauge wire from the Remote Tum-On Lead on your source unit to the REM wire on the PXA harness. (Best
for Lo-Level input)
• DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when
the source unit has been turned on. (Best for Hi-Level input)
Input Level: The RCA inputs on KICKER PXA amplifiers are capable of receiving either Hi or Low-level signals
from your source unit. When using a Hi-Level signal, simply set the Input Level switch on the amplifier to HI.
HI-PASS Switches: Use the HI -PASS switches behind the protective rubber covering of the amplifier to set the
internal crossover. Choose a cutoff of 60Hz, 80Hz, 120Hz, or OFF depending on the configurati on of switches.
Never change the switches with the audio system on!
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it
down a little.
4

TROUBLESHOOTING
If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Power
Protection LED on the side power panel of your Kicker PXA senes amplifier. Depending on the state of the
amplifier and the vehicle's charging system, the LED will glow either Red or Blue. When the blue LED is lit this
indicates the amplifier is turned on and no trouble exists.
Blue LED off, no output? With a Volt Ohm Meter (VOM) check the following: 0 +12 volt power terminal
(should read + 12V to +16V) @Remote tum-on terminal (should read +12Vto +16V) @Check for reversed
power and ground connections 0 Ground terminal, for proper conductivity. 0 For Hi-Level input, check input
wires for +6V.
Blue LED on, no output? Check the following: O RCA connections @Test speakeroutputs with a "known"
good speaker. @Substitute source unit with a "known" good source unit. 0Check for a signal in the RCA
cable feeding the amplifier with the VOM meter set to measure "AC" voltage.
Protection LED flashing with loud music? The red LED indicates low battery voltage. Check all the
connections in your vehicle's charging system. It may be necessary to replace or charge your vehicle's battery or
replace yourvehicle's alternator.
Protection LED on, no output? 0 Amplifier Is very hot = thermal protection Is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow around
the amplifier. @Amplifier shuts down only while vehicle is running -voltage protection circuitry is engaged.
Voltage to the amplifier is not within the 10-16 volt operating range. Have the vehicle's charging and electrical
system inspected. @Amplifier will only play at low volume levels= short circuit protection is engaged. Check
for speakerwires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)
operating below the minimum recommended impedance.
No or low output? 0Check the balance control on source unit @Check the RCA (or speaker input) and
speaker output connections.
Alternator noise-whining sound with engine's RPM? 0Check for damaged RCA (or speaker input) cable
@Check the routing of RCA (or speaker input) cable @Checkthe source unit for proper grounding 0Check
the gain settings and turn them down if they are set too high.
Reduced bass response? Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s); if the bass improves, the speaker was out of phase.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers' head units.
Some head units may require additional grounding to prevent noise from entering the audio signal. If you are
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the
head unit to the chassis will remedy this issue.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the
vehicle.
If you have more questions about the installation or operation of
your new KICKER product, see the Authorized KICKER Dealer
where you made your purchase. For more advice on installation,
click on the SUPPORT tab on the KICKER homepage, www.
kicker.com. Choose the TECHNICAL SUPPORT tab, choose
the subject you are interested In, and then download or view the
corresponding information. Please Email [email protected] or
call Technical SeNices [phone] for unanswered or specific
questions.
5

ELECTRONICS LIMITED WARRANTY
When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material
and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase. If this product is
identified as "Refurbished" or "B Goods", the warranty is limited to a period of THREE (3) MONTHS from date of original
purchase. In all cases you must have the original receipt. Should service be necessary under this warranty for any reason
due to manufacturing defect or malfunction during the warranty period, KICKER will repair or replace (at its discretion)
the defective merchandise with equivalent merchandise. Warranty replacements may have cosmetic scratches and
blemishes. Discontinued products may be replaced with more current equivalent products. This warranty is valid only for
the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of
the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty
gives you specific legal rights; however you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned toyour local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at [phone] for a Return Merchandise Authorization (RMA) number. Package only
the defective items in a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return offunctioning items increases your return freight charges. Non-defective items will be returned fre1ghtcollect to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing the Customer's
name, Dealer's name and invoice number, and product purchased. Warranty expiration on items without proof-of-
purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost orexpense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization (RMA) number
o Products purchased from an UNAUTHORIZED dealer
o Freight Damage
o The cost of shipping product to KICKER
0 Service performed by anyone other than KI CKER S) sti Ilwaterdesigns
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.)
returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps
may void your warranty. Any questions can be directed to the KICKER Customer Service Department at [phone].
Contact your International KICKER dealer or distributor concerning specific procedures for your country's warranty
policies.
Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most
current information.
18 15PXA.2-D-20151023

INTERNATIONAL WARRANTY
Contact your International KICKER dealer ordistributor concerning
specific procedures for your country's warranty policies.
WARNING: KICKER products are capable of producing sound levels
that can permanently damage your hearing! Turning upa system to a
level that has audible distortion is more damaging to your ears than
listening to an undistorted system at the same volume level. The
threshold of pain is always an indicator that the sound level is too loud
and may permanently damage your hearing. Please use common
sense when controlling volume.
GARANTIA INTERNACIONAL Versi6n Espanol
Our goods come with guarantoes that cannot be
excluded under the Australian Consumer Law
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced 11 the
goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Comunfquese con su concesionario o distribuidor KICKER internacional para obtener infor aci6n sobre procedimientos especfficos
relacionados con las normas de garantfa desu pafs.
ADVERTENCIA: Los excitadores KICKER son capaces de producir niveles de sonido que pueden daiiar permanentemente
el ofdo. Subir el volumen del sistema hasta un nivel que produzca distorsi6n es mas danino para el ofdo que escuchar un
sistema sin distorsi6n al mismo volumen. El dolor es siempre una indicaci6n deque el sonido es muy fuerte y que puede daiiar
permanentemente el oido. Sea precavido cuando controle el volumen.
La frase "combustible para vivir la vida Livin' Loud™ a todo volumen" se refiere al entusiasmo por la vida que la marca KICKER
deestereos de autom6vil representa y a la recomendaci6n a nuestros clientes de que vivan lo mejor posible ("a todo volumen"}
en todo sentido. La lfnea de altavoces y amplificadores KICKER es la mejor del mercado deaudio de autom6viles y por lo tanto
representa el "combustible" para vivir a todo volumen en el area de ·estereos de autom6vil" de la vida de nuestros clientes.
Recomendamos a todos nuestros chentes que obedezcan todas las reglas y reglamentos locales sobre ruido en cuanto a los
niveles legales y apropiados de audici6n fuera del vehfculo.
INTERNATIONALE GARANTIE
Deutsche Version
Nehmen Sie m1t lhren internationalen KICKER-Fachhandler oder Vertrieb Kontakt auf, um Details uber die Garantieleistungen in
lhr em Land zu erfahren.
WARNUNG: KICKER - Treiber konnen einen Scha\lpegel erzeugen, der zu permanenten Gehorschaden fuhren kann! Wenn Sie ein
System auf einen Pegel stellen, der horbare Verzerrungen erzeugt, schadet das lhren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstarkepegel. Die Schmerzschwelle ist immer eine Anzeige dafur, dass der Schallpegel zu laut isl und zu
permanenten Gehorschaden fuhren kann. Seien Sie bei der Lautstarkeeinstellung bitte vernunftig!
Der Slogan "Treibstoff fur Livin' Loud" bezieht sich auf die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen, in alien Aspekten ihres Lebens nach dem Besten ("Livin' Loud"} zu streben. Die
Lautsprecher und Verstarker von KICKER sind auf dem Markt fur Auto-Soundsysteme fuhrend und stellen som1t den "Treibstoff"
fur das Autostereoerlebnis unserer Kunden dar. Wir empfehlen alien unseren Kunden, sich bezuglich der zugelassenen und
passenden Lautstarkepegel auBerhalb des Autos an die ortlichen Larmvorschriften zu halten.
GARANTIE INTERNATIONALE Version
Fram;aise
Pour connaitre les procedures propres a la politique de garantie de votre pays, contactez votre revendeur ou distributeur
International KICKER.
AVERTISSEMENT: Les haut-par1eurs KICKER ont la capacite de produire des niveaux sonores pouvant endommager l'ou'fe de
faQon irreversible ! L:augmentation du volume d'un systeme jusqu'a un niveau presentant une distorsion audible endommage
davantage l'ou'fe que l'ecoute d'un systeme sans distorsion au meme volume. Le seuil de la douleur est toujours le signe que le
niveau sonore est trop eleve et risque d'endommager l'ou'fe de faQon irreversible. Reglez le volume en faisant prevue de bon sens!
L:expression " carburant pour vivre plein pot • fail reference au dynamisme de la marque KICKER d'equipements audio pour
vehicules et a pour but d'encourager nos clients a faire le maximum(" vivre plein pot"} dans tousles aspects de leur vie. Les
haut-par1eurs etamplificateurs KICKER sont les meilleurs dans le domaine des equipements audio et representent done pour nos
client le " carburant pour vivre plein pot " dans l'aspect " installation audio de vehicule "de leur vie. Nous encourageons tous nos
clients a respecter toutes les lo1s et reglementations locales relatives aux niveaux sonores acceptables al'exterieur des vehicules.
P.O. Box 459 • Stillwater, Oklahoma 74076 •USA • [phone]
19

LIMITED WARRANTY
(fKICKER
MOTORCYCLE AUDIO KIT
Please retain this card and your receipt with your vehicle.
It contains valuable information shou ld you need service.
Authorized Dea l er:
Purchase Date:
- llll ll l ll ll lIll llll ll ll ll ll ll ll
Model Number:
44146508001028
Seria l Number:

LIMITED WARRANTY
When purchased from an Authorized KICKEn Dealer, KICKER warrants KICKrn products to be free from delects in material and workmanship for THRE E (3) YEARS from dale of or i ginal purchase with receipt.
In all cases you must have the original receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or rnaltunction during the warranty period, Kicker will repair or replace
(at its discretion) the defective merchandise with equivalent morcriandiso al no charge . Warranty rop l acemonts may have cosmetic scratches and blemishes. Discontinued products may be replaced with more
cur rent equivalent products.
!his warranty is valid on ly for tho original purchaser and is not extended to owners of tho product subsequent to tho origina l purchaser . Any applicable implied warranties are l imited in duration to a period of
the express warranty as provided herein beginning with the date of the original purchase at retail, and no warrant i es, whether express or implied, sha ll apply to th is product thereafter. Some states do not allow
limitations on imp l ied warranties; therefore those exc l us i ons may not apply to you . This warranty gives you specifi c legal rig h ts; however you may have other ng h ts that vary from slate to stat e.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Dofeclivo morchandiso should bo r etu r ned to your loca l Authorized Sti ll water Designs (Kicker) Doalor for warranty serv ice. /\ssistanco in l ocating an Authorized Dealer can be found at wvvW.kicker.com or by
contacting Sti ll water Designs directly . You can confirm that a dealer is aulhoriLed by asking to see a current authorized dea l er window decal. II il becomes necessary for you to return defective merchandise
directly to Sti ll water Designs (Kicker), ca ll the Kicker Customer Service Department at [phone] for a Return Me r chandise Authorizat ion (RMA) number. P ackage all defective items in the original conta i ner
or in a package lriat wi ll prevent shipping damage. and return to:
Sti llvva ter Designs, 3100 North Husband Road , Stillwater, OK 74075
1he HMA number must be clearly marked on the outside ol llie package . Please return only defective components. The return of functioning items i ncreases your return freight charges. Non-defect i ve it ems
will be returned freight -co ll ectto you. Include a copy of the original receipt with the purc h ase dale clearly visible, and a "proof-of-purct1ase" statement li sting the Customer's name, Dea l er's name and invo ice
number, and product purchased. Warranty expiration on ilorns without proof-of-purchase will bo determined from the typo of sa le and manufacturi ng data code .,- roigh t must be prepaid; items se nt froight-
co ll ect, or COD, will be refused .
WHAT IS NOT COVERED?
This warranty is valid only if the product is used tor the purpose for which it was designed. It does not cover:
Damage due to improper installation
Spea k ers damaged due to amplifier clipping or distortion
Any cost or expense related to the removal or reinstallation of product
Products returned wrthout a Return Merchandise Authorization (llMI\) number
Items previously repaired or mod i fied by any unauthorized repair facility
rreight Damage
Return shipping on non-defective items
Products with tampered or missing barcode labels
Products purchased from an UNAUTHORIZED dealer
Damage caused by exposure to moisture, excessive heat, chemica l cleaners, and/or UV radiation
Damage through neg li gence, misuse, accident or abuse. Repeated returns for the same damage may be considered abuse
HOW LONG WILL IT TAKE?
Subsequent damage to other components
Service perforrned by anyone other than KICKER
Products with tampered or missing seria l numbers
The costof shipping product lo KI CKER
Kicker strives to maintain a goal ot one week for turnaround on service of all acoust i cs (subwoofers. midrange and coaxial drivers, tweeters, crossovers etc) returns. Delays may be incurred if lack of replacement
inventory or parts is encountered . Failure to follow these stops may void your warranty. Any questions can be directed to tho Kicker Customer Sorvico Department at (405) 624-851 0.