Kicker FHDESU14 User manual

PROGRAMMING HD RADIO
NOTE: It is necessary to purchase a KICKER TDHDP Radio Flash Programmer or to have a motorcycle shop re-flash your radio before installation!
GETTING STARTED
1. Remove the seat and disconnect both negative and positive battery terminals.
2. Remove the windshield.
3. Remove the outer fairing.
a. Remove the four mounting screws, unplug the headlamp and set aside on a soft cloth.
4. Remove the fuel tank.
a. Unplug the fuel fitting on the left side of the tank. You may remove the console if you want to retain vent line routing and connector
placement.
b. Remove all four mounting bolts and carefully lift the tank off the bike and set aside.
5. Remove wire caddy cover.
a. Carefully release each tab along the caddy until it lifts completely.
SPEAKER INSTALLATION
6. Remove one of the white speaker pods from the inner fairing. (Fig. 1)
a. There are five fasteners in the center portion and three on the outside to release it from the inner fairing.
7. Remove the stock speaker and replace with the PSC652 speaker from the kit.
a. Install the provided speaker ring adapter onto the speaker pod. (Fig. 2)
b. Install the speaker into the pod and fasten with the original speaker screws. (Fig. 3)
8. Reinstall the pod to the inner fairing.
9. Repeat for the other side.
AMP INSTALLATION
Note: There may be some connectors that will need to be relocated off of the radio chassis for the amp bracket to fit.
10. Fasten the amplifier to the bracket with the supplied hardware.
a. Insert the bolts through the bottom of the bracket and install the locknuts to the amplifier.
11. Using the supplied ¼” hardware, fasten the amp/bracket assembly to the radio chassis with the 12-pin connector facing the clutch side.
HARNESS INSTALLATION
12. Plug the harness into the amplifier and route the speaker wires to their respective locations. (Fig. 6)
a. Separate the speaker connectors and plug in the amplifier harness to each speaker.
13. Plug the switched power harness into the 2-place amp connector on the right side of the fairing. (Fig. 7)
14. Plug the blue wire on the kicker harness into the switched power harness lead with one wire.
a. This allows for an accessory 12V port to remain available.
15. Route the power leads along the left side of the frame neck, in the lectrical caddy to the seat area. (Fig. 8)
16. Reconnect the battery terminals.
FHDESU14
Motorcycle Audio Kit for Harley Davidson®
Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes
2014–Newer (FLHT)
Package Contents:
(1) Install Guide (2) Wiring Harnesses (4) Black Cable Ties
(2) 6-1/2” KICKER Speakers (4) 8-32 x 1/2” Button Head Bolts (1) Stainless Steel Mounting Bracket
(1) 120W/60W KICKER Amp (4) 8-32 Nylock Nuts (1) Mounting Hardware
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque specifications. KICKER is not responsible for damage resulting from improper installation techniques. This kit may not
be compatible with some aftermarket head units.
FRONT KIT PROGRAMMING WITH KICKER TDHDP
Follow instructions included with KICKER TDHDP
FRONT & REAR KIT PROGRAMMING WITH KICKER TDHDP
Follow instructions included with KICKER TDHDP

SYSTEM SETUP
Note: At this time, it is highly recommended to set the amp gain setting to 0. KICKER recommends that the dip switches be set up as follows:
Auto turn-on - 12V Input level - HI HI-PASS – 80 Hz Input Gain control – 0
17. Plug the radio in, but do not reinstall it until the gain has been set.
18. Test component function and set the gain to optimize system performance.
19. Carefully reassemble the motorcycle and enjoy your new audio kit!
Note: These two leads are amplified and non-amplified speaker outs with auxiliary switched power. They are intended to provide ease of
installation for speaker lid speakers or other add-on audio. (Fig. 9)
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. FHDESU14-A-20180326
1234
5 6 7 8
910

PSC65
English Version
Versión Español
Altavoces Coaxiales PS
Deutsche Version
PS Koaxial-Lautsprecher
Version Francaise
Haut-parleurs Coaxiale PS
PS Coaxial Speakers
2015 PSC65 Rev E.indd 1 9/25/2015 8:54:08 AM

2
PSC65 COAXIAL SPEAKERS
Owner’s Manual
PERFORMANCE
INSTALLATION
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Woofer Size | in [mm] 6 1/2 [160]
Tweeter Size | in [mm] 3/4 [20]
Frequency Response | Hz 40–20k
Max Recommended Amplifier Power [Watts] | PEAK/RMS 120W/60W
Sensitivity [SPLo] | dB @ 1W, 1m 92.5
Nominal Impedance [Zn] | ohm 2Ω (PSC652), 4Ω (PSC654)
Weight | oz [g] 15.2 [430]
Mounting Hole Diameter | in [mm] 5 1/16 [128]
Mounting Depth | in [mm] 2 [50]
Top Mount Height | in [mm] 1/4 [6.5]
Please refer to your bike’s factory service manual for disassembly/installation information. Typically, you
should retain all factory screws, hardware, and grilles when upgrading your bike to a KICKER system. The
KICKER PSC65 is compatible with factory locations using the included gaskets. If you are doing a custom
installation, be careful not to drill into wiring or vehicle mechanisms. You are solely responsible for securely
mounting the speakers. Use the included grilles and screws only when performing a custom installation.
1. Remove your motorcycle’s instrument panel according to the
manufacturer’s service manual.
Package Contents:
(2) PSC65 Speakers (2) 12” wiring harnesses
(8) M4 x 25mm pan cross head woodscrews (8) M4 speed nuts
(4) 22ga, red crimp-style butt connectors (4) Gaskets
(2) Grilles (2) Kicker badges
WARNING: KICKER products are capable of producing sound levels that can permanently damage your
hearing! Turning up a system to a level that has audible distortion is more damaging to your ears than
listening to an undistorted system at the same volume level. The threshold of pain is always an indicator
that the sound level is too loud and may permanently damage your hearing. Please use common sense
when controlling volume.
2015 PSC65 Rev E.indd 2 9/25/2015 8:54:19 AM
{fKICKER

3
2. Remove factory speakers.
Remove the screws securing the factory speakers.
Remove the speaker connectors while removing the factory speaker.
NOTE: 2014 Harley Davidson - It is necessary to remove the outer fairing and speaker housings.
3. Install PSC65 in factory location.
Connect the factory speaker connectors to the PSC65 terminals.
Mount the PSC65 to the desired location with the proper gasket and secure using the factory hardware.
Re-install your bike’s access panel in the reverse order you disassembled it.
F
E
Honda factory speaker location
Honda gasket
custom install only
Harley gasket
2015 PSC65 Rev E.indd 3 9/25/2015 8:54:19 AM
/ /