KinAn HT2808 User manual

Matrix KVM over IP Console
(8 Port /16 Port/24 Port/32 Port)
User Manual
www.kinankvm.com
@all right reserved Shenzhen Kinan Technology Co., Ltd
Print date: 2019 / 12
Version: V1.3

8 Port /16 Port/24 Port/32 Port User Manual
- 1 -
Table of Contents
1. Product Overview.....................................................................................................2
1.1 Introduction.................................................................................................2
1.2 Features......................................................................................................2
1.3 Appearance.................................................................................................4
2. Installation and Start-up............................................................................................6
2.1 Rack Mounting............................................................................................6
2.2 Install KVM Components ............................................................................7
2.3 Opening the Console..................................................................................8
2.4 Closing the console.....................................................................................9
3. LED Operation.....................................................................................................10
3.1 LED Functions ..........................................................................................10
3.2 Operating the Monitor ...............................................................................12
3.3 Key Combination Function........................................................................13
4. User Interface Operation.........................................................................................14
4.1 User..........................................................................................................15
4.2 System......................................................................................................19
4.3 Security.....................................................................................................21
4.4 Maintenance .............................................................................................23
5. Remote Control......................................................................................................24
5.1 Configure the Target Server...................................................................... 24
5.2 Remote WEB Interface Settings ...............................................................26
5.3 Log in........................................................................................................29
5.4 Video Control Interface Menu ...................................................................30
6. IP Menu Option...................................................................................................36
6.1 User Management ....................................................................................36
6.2 System Settings........................................................................................41
6.3 Safety Management..................................................................................43
6.4 System Maintenance ................................................................................44
7.Appendix................................................................................................................46
7.1 Specifications (18.5”) ................................................................................46
7.2 Grounding Requirements..........................................................................47

8 Port /16 Port/24 Port/32 Port User Manual
- 2 -
1. Product Overview
1.1 Introduction
The IP-based KVM (IP-KVM) redirects the local keyboard, mouse and video data to a remote
management console. The operator can safely manage one or many computers locally at
the server site or remotely via a standard internet browser. Securely gain BIOS level access
to systems for maintenance, support or failure recovery over the internet.
The IP-KVM console integrates multiple KVM switches in a 1U height console. It can control
multiple computers with a set of devices including monitor, keyboard and mouse; saving
cost and space by consolidating the hardware to a single device.
The IP-KVM console is fast and easy to install. Simply connect corresponding cables to the
correct ports of the KVM and its module without software configuration. Connect multiple
computers with compact RJ-45 connectors and CAT5e/6/7 cables, transmitting distance is
up to 100M.
1.2 Features
Hardware
18.5” TFT LCD monitor, high definition and high resolution
Rack-mountable in a 1U EIA system rack
Full size keyboard with integrated number pad
Trackball eliminates the need for a separate, external mouse
Local Console
Control up to 8 / 16/ 24 / 32 computers
Support 1 local user and 1 remote user, port share mode allows local and remote
users to gain access to a server simultaneously
Easy-to-use switching by browser-based UI interface, hotkeys and pushbuttons
Support servers with VGA port
Multiplatform client support (Windows, Linux, Unix, Mac, Solaris (Sun), Redhat,
Ubuntu
Supports a graphical interface for intuitive and convenient human-computer
interaction- local resolution is up to 1920 x 1080@60Hz
Supports mouse synchronization mode-automatically synchronizes the local and
remote mouse movements
Video synchronization with local console - EDID information for local console
display can be stored in the host module for video resolution optimization

8 Port /16 Port/24 Port/32 Port User Manual
- 3 -
Keyboard and mouse emulation to ensure the normal booting
Auto scan feature for monitoring user-selected computer
Hot pluggable –add or remove computers without having to power down the
switch
Remote Console
Adaptive 10 / 100 / 1000 Mbps network
WEB browser-based Or KVM_Clients remote management
BIOS-level access
Video quality and video tolerance can be adjusted to optimize data transfer
speed, up to 30 FPS
Full screen or scalable video display
Remote users and local users can control the same server synchronously
Support AES / DES / 3DES encryption
Support audit function-allows the administrator to audit the device through the
system log and operation log
Exit Macros support
Configurable user and group permissions for server access and control
Supports firmware upgrade

8 Port /16 Port/24 Port/32 Port User Manual
- 4 -
1.3 Appearance
Front View
Figure 1.1 Front view
1. LED Monitor
2. Rear Bracket Slot
3. LED OSD Controls
4. Front Bracket
5. Keyboard
6. Touchpad
7. Handle
8. Release Catch
9. Display Panel
10. Switch LED

8 Port /16 Port/24 Port/32 Port User Manual
- 5 -
Structure and Size (18.5)
Figure 1.2 18.5” console size dimensions
Rear View
8
LAN RS485
LAN RS485
7
6
54
232 1
Figure 1.3 Rear view
1. Ground Screw
2. Power Input (AC/DC)
3. Power Switch
4. LAN Port
5. USB Port
6. RS485 Port
7. Monitor Port
8. PC Connecting Port

8 Port /16 Port/24 Port/32 Port User Manual
- 6 -
2. Installation and Start-up
2.1 Rack Mounting
A standard rack mounting kit is provided to mount the switch in a depth of 620-720mm (18.5”)
in a standard 19” rack. For other mounting distances, the rear brackets need to be
customized accordingly. With one person hold the switch in place, the other person slides
the L bracket into the switch’s side mounting brackets from the front to the back, then screws
the brackets to the rack (see below installation drawing).
Figure 2.1 Rack Installation Diagram

8 Port /16 Port/24 Port/32 Port User Manual
- 7 -
2.2 Install KVM Components
Figure 2.2 Installation diagram
Installation Steps:
1. Make sure the KVM console has been connected to the ground.
2. Connect the KVM adapter to the PC or Server.
3. Connect the KVM adapter to the KVM port with a CAT5 cable.
4. You can remote control the KVM switch via IP.
5. Using power adapter to connect the KVM into 220V AC power supply.
6. Power on the switch
7. Connect the external keyboard, mouse and monitor (optional)
Module Explanation
PS/2 CPU module
USB CPU module
Components
Functions
Green
indicates that the KVM has connected to its corresponding
computer and power on.
Orange
indicates that the computer attached to its corresponding
port is up and running.

8 Port /16 Port/24 Port/32 Port User Manual
- 8 -
2.3 Opening the Console
1. Release the release catch;
UNLOCK
UNLOCK
UNLOCK
UNLOCK
Figure 2.4 Unlocking
Note: The release lock can only do horizontal locking, it doesn’t bear any load.
2. Pull the KVM console all the way out until it clicks into place;
3. Rotate the LCD module all the way back to expose the LCD screen; the LCD module
can be rotated up to 108°.
Best Resolution :
1920x1080@60Hz
Figure 2.5 Open angle of the console
4. The KVM makes two “beep” sounds after power on, the orange light keeps flashing
and an UI window appears for you to input user name and password.
User Name:
admin
Password:
admin

8 Port /16 Port/24 Port/32 Port User Manual
- 9 -
5. LCD panel is powered on when the power LED is green.
6. Power on the computer or server after power on the KVM.
2.4 Closing the console
Close the LCD display panel and the power automatically shut down.
Push the KVM into the cabinet: When pushing forward, the rail will be unlocked
automatically; push forward until the KVM is fully pushed into the cabinet,
the KVM will be automatically locked.
Diagram 2-6 unlocking the console

8 Port /16 Port/24 Port/32 Port User Manual
- 10 -
3. LED Operation
3.1 LED Functions
Figure 3.1 LED front views
No.
Components
Function
1
1-16
Switching freely from port 1 to port 16
Reset
Press 【1】and 【2】at the same time for three
seconds resets the keyboard and mouse
Scan
Press【7】and【8】at the same time for three seconds
enters the auto scan mode.
Brightness
Press 【3】for three seconds enters brightness
adjusting mode.
33 are flashing on the LED tube.
Then press 【5】，【6】to adjust.
Press【3】exits or waits for five seconds and it will
auto-exit.
Definition
Press 【4】for three seconds enters definition
adjusting mode.
44 are flashing on the LED tube.
Then press 【5】，【6】to adjust.
Press 【4】exits or waits for five seconds and it will
auto-exit
Initialize
Press 【6】for three seconds will initialize the
brightness and definition of each port.
2
Port Selection
Buttons & LEDs
Indicator LEDs are built into the switches, the online
LED light is on the left and the selected LED light is on
the right.
1. An online LED light (green) indicates that the
KVM has connected to its corresponding
computer and power on.
2. A selected LED light (orange) indicates that the
computer attached to its corresponding port is
up and running.
3
Station ID
Display the current port

8 Port /16 Port/24 Port/32 Port User Manual
- 11 -
Figure 3.2 32 Port LED front views
No.
Components
Function
1
0~9 +Enter
Switching from port 1 to port 32
Port 8 : If you want to switch to Port 8, press【8】,
and the LED light displays , then press “Enter”,
you will come to Port 8.
Port 32: If you want to switch to Port 32, press【3】
and【2】, the LED light displays , and then press
“Enter”, you will come to Port 32.
2
(+, -)
Adjust Brightness
Press , the LED light blinking with , and then
press “+” and “–“to adjust the brightness.
3
(+, -)
Adjust Definition
Press , the LED light blinking with , and then
press “+” and “-“to adjust the definition.
4
Station ID
Display the current port

8 Port /16 Port/24 Port/32 Port User Manual
- 12 -
3.2 Operating the Monitor
Figure 3.4 Monitor adjust menu buttons
The LED OSD allows you to set up and configure the LED display.
Buttons
Functions
MENU SELECT
Brings up the main menu.
EXIT/AUTO
Exits the current menu and returns to the previous menu or
exits the LED OSD.
Press AUTO for automatic configuration.
SL-/SL+
Moves the menu to make corresponding adjustment.
LED state
Green: Running
Red: Power off or access non standard VESA signal
Flashing green: Energy saving mode or no signal
Press AUTO if the screen migrates after power on or under other circumstances, then the
screen auto-configures to its best display state.
Note:
It may not be adjusted to its best state if part of the display mode is not standard
VESA mode. if so, return back to OSD menu to RESET, then it will revert back to
normal.
It is recommended to set up the display mode at 1920×1080@60Hz, refresh rate
at 60Hz.

8 Port /16 Port/24 Port/32 Port User Manual
- 13 -
3.3 Key Combination Function
If you want to set other hotkeys to pop up the UI interface or key combination switch, set
up the via the local console, 【System Settings】> 【Device info】
Pop up the
UI interface
Double click【L_Ctrl】
Double click【L_Alt】
Double click【Scroll Lock 】
Double click【Caps Lock】
Hot key
【L _Alt】+【L_Ctrl】
【L_Win】+【L_Ctrl】
【L_Alt】+【L_Win】
Hotkey commands are as follows：
Hot key + the corresponding function key
Function
Operating
Function description
Port switch
+Number
Skip ports from 1~16
+ 【↑】/【←】
Skip to previous port
+ 【↓】/【→】
Skip to next port
Brightness
+【+】
+
+【-】
-
definition
+【>】
-
+【<】
-
Reset Video
+【R】
Reset the video
Lock KVM
+ 【L】
Lock KVM and a user login window
appears

8 Port /16 Port/24 Port/32 Port User Manual
- 14 -
4. User Interface Operation
login UI control menu
User Name: admin
Password: admin
After logging in the device, you can see the connection status of the device port.
In the port list,
1. Click the “Connect" to enter the host screen;
2. In the host screen, press the [L_Ctrl] key on the keyboard twice.
3. Return to the UI interface.

8 Port /16 Port/24 Port/32 Port User Manual
- 15 -
4.1 User
User management mainly set up for user& user group adding, delete and modifying, user
password modification, user group permissions and so on. If the user do not have user
management authority, the user cannot access to user management interface. The user in
this section is who have the user management authority.
User List
User list interface: List all registered users, you can see more by page turning
•User name or full user name search
Input user name, it shows related users which make it convenient when you have a
large number of users
•Add user
Click【add】button, the window below appears:

8 Port /16 Port/24 Port/32 Port User Manual
- 16 -
Note: In this window, “*” is required content
1. User name: user name can contains only low case letters, number and “_”
2. Enter password: without strong password protection, the password can only
compose of 1-16 letters, numbers or special characters (-@.$! _)；With strong
password protection, the password should be filled in according to the rules of strong
password protection. More details please check “security management—＞
security setting—＞strong password”
3. User group：Select the corresponding user group
User group list
User group list interface: List all registered users, you can see more by page turning
•User group name search
Input user group name, it shows related user groups which make it convenient
when you have a large number of users
•Add user group
Click【add】button, the window below appears

8 Port /16 Port/24 Port/32 Port User Manual
- 17 -
1. User group name: it contains only low case letter, number and “_”
2. Authority：mainly refers to management authority and operation authority, click
show more, authority menu appears(shown in picture above), click show less,
authority menu disappears
•Port Access: Authority to access KVM, and control target server
•User Management: user management authority
•Device Setting: KVM device management authority
•Security Management: security management authority
•System Maintenance: system maintenance authority
3. Port authority：Set up access and operating authority for each port
Change password
The passwords which is using for logged user
Note: In this window, “*” is required content

8 Port /16 Port/24 Port/32 Port User Manual
- 18 -
1. User name: user name can contains only low case letter, number and “_”
2. Enter password：without strong password protection, the password can only compose
of 1-16 letters, numbers or special characters (-@.$! _)；With strong password
protection, the password should be filled in according to the rules of strong password
protection. More details please check “security management—＞security setting—
＞strong password
3. User group：Select the corresponding user group

8 Port /16 Port/24 Port/32 Port User Manual
- 19 -
4.2 System
Network settings
IPv4 address setting:
•IP address: preset IP address
•Subnet mask: Generally, it should be consistent with other devices in the network.
•Default gateway: Generally, it should be consistent with other devices in the network.
•MAC address：physical address
•DCSG IP: the IP address should be the same with the Authentication Server
IP address
•DCSG Port: the Port should be the same with the Authentication Server Port.
.