King Pigeon RTU5012 User manual

GSM SMS Alarm & Dialer
-- Ultra Version!
Inquiry Onsite AC
Power Status with a
SMS!
Cost-Effective GSM
Dialer Solution In
The Worldwide!
User Manual
RTU5012
Ver 1.1
Date Issued: 2013-11-12
All rights reserved by King
Pigeon Hi-Tech.Co.,Ltd.
www.GSM-M2M.com
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm

Page 2 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
Warming Tips---Quickly Guide
If you need the AC power monitoring function only, please read the chapter 5.7~ 5.8, 6.2, 6.14, 6.16 and chapter 7.3 to get
the quickly settings to save you time. After you setup, please remove the RTU5012AC/DCAdaptor to check if you can get
SMS alert according to the 6.16 preset time.
Index
SMS Command List
SMS COMMAND
Functions & Actions
AA
To arm the GSM Dialer, in this mode, any detector triggered will alarm.
BB
To disarm the GSM Dialer, in this mode, detector triggered will not alarm.
CC
To switch on the siren.(The function available after 2014-03-15)
DD
To switch off the siren. (The function available after 2014-03-15)
EE
Inquiry the RTU5012 Status and GSM Module IMEI Code.
*The commands should plus Password, the format is Password+SMS Command. i.e.: if the password is 1234, then
you can send 1234AA to arm, 1234BB to disarm, the AA~EE must be Caps Lock.
This handbook has been designed as a guide to the installation and operation of GSM Dialer and GSM Power
Monitoring Alarm.
Statements contained in the handbook are general guidelines only and in no way are designed to supersede the
instructions contained with other products.
We recommend that the advice of a registered electrician be sought before any Installation work commences.
The manufacturer, its employees and distributors, accept no liability for any loss or damage including consequential
damage due to reliance on any material contained in this handbook.
The manufacturer, its employees and distributors, accept no liability for GSM Network upgrading or SIMCard
upgrading due to the technology specifications contained in this handbook.
1.Brief introduction --------------------------------------3
2.Safety Directions --------------------------------------3
3.Standard Packing list ---------------------------------4
4.Mainly Features ----------------------------------------4
5.Installation and Connection Diagram -----------5
5.1Inserting the SIMCard -----------------------------5
5.2Making the Outlets for wires-------------------6
5.3Contacting the Wired Sensor,CCTV,IP Camera
or Other Alarm Panel to the GSM Dialer ------6
5.4Contacting the Siren, hooter -------------------8
5.5Contacting the Backup Battery ---------------8
5.6Contacting the External GSM Antenna ------9
5.7Contacting the AC/DC Power Supply---------9
5.8Switching on/off the GSM Dialer-------------10
5.9Amounting the GSM Dialer-------------------10
5.10Reset to Factory Default ----------------------10
6.Settings--------------------------------------------------10
6.1Setup New Password-----------------------------12
6.2Setup Authorized number----------------------12
6.3Inquiry the Authorized number-----------------13
6.4Remove the Authorized Number--------------13
6.5Modify the wired zone type----------------------13
6.6Modify the SMS Alarm Content---------------13
6.7Inquiry the SMS Alarm Content Setting------13
6.8Setup the Zone Attribute -------------------------------14
6.9Setup the Siren Sound time--------------------------14
6.10Setup the Alarm Delay Time--------------------------14
6.11Setup the Arm Delay Time----------------------------15
6.12Enable to Alert the first Authorized Number ---15
6.13Required the GSM Dialer callback------------------15
6.14Setup External Power Status Alert Feature-------15
6.15Setup Siren Response Feature ---------------------16
6.16Setup Automatically report Status function--------16
7.Operating Instructions --------------------------------------16
7.1Armed or Stay WITH a FREE call --------------------16
7.2SMS Commands for Arm or Disarm or Switch
On/Off Siren. ----------------------------------------------17
7.3Inquiry Status and GSM Module IMEI Code--------17
7.4iOS App and Android Apps Instructions--------------18
8.Technical specifications-------------------------------------18
9. Maintenance----------------------------------------------------18
10.Warranty --------------------------------------------------------19
11.Affix Table------------------------------------------------------19
Table 1. GSM Dialer Installation Schedule---------------19
Table 2. GSM Dialer SMS Command List-----------------19

Page 3 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
1. Brief introduction
The GSM Dialer is an Ultra Version of GSMAlarm, includes multi-functions and ultra low cost and high
reliability special for Residential areas, business area, commercial area, office, factory, industrial area and
other Varity applications. It integrated high performance GSM Module and MCU inside, and with innovative
and experienced functions and features to meet the required and potential demands in the worldwide
markets.
The user can receive SMS Text and calling from the GSM Dialer once the alarm occurrence immediately.
Also, remotely switch the GSM Dialer to arm or disarm with free call from mobile phone, or remotely call in
the GSM Dialer to listen in on-site, or send SMS Command to request the GSM Dialer call back.
The GSM Dialer equips 1 wired inputs for IP Camera Alarm Output, other alarm panel output to transfer
alarm message by SMS over GSM Network.
The GSM Dialer inbuilt power detection circuit, no need any other detector or sensor to monitoring the
external power directly. Once external power goes off or goes on, the GSM Dialer can send SMS or dial
upto 6 authorized mobile phones.
2.Safety Directions
Safe Startup
Do not use GSM Dialer when using GSM equipment is prohibited or might bring disturbance
or danger.
Interference
All wireless equipment might interfere network signals of GSM Dialer and influence its
performance.
Avoid Use at Gas Station
Do not use GSM Dialer at a gas station. Power off GSM Dialer when it near fuels or
chemicals.
Power it off near Blasting Places
Please follow relevant restrictive regulations. Avoid using the device in blasting places.
Reasonable Use
Please install the product at suitable places as described in the product documentation. Avoid
signal shielded by covering the mainframe.

Page 4 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
Use Qualified Maintenance Service
Maintenance can be carried out only by qualified maintainer.
3. Standard Packing List
GSM DialerX1
User Manual X1
Optional Accessories: (Wired detectors)
PIR Motion Sensor, Glass Break Sensor, Magnetic Window Sensor, Temperature Sensor, Infrared Beam
Fence, Vibration sensor, AC power status detectors.
4. Mainly Features
Supports Away Armed, Partial Armed(At House or Stay) or Disarmed by SMS Commands, Call in with
free charge;
Supports 6 Authorized Numbers, each number can be setup as receive SMS or receive call or both of
them, also, each number can be setup authorized to call in to arm or stay the system;
Automatically send SMS Alert Alarm Message and dial to the authorized numbers when alarm
occurrence;
Supports 1 wired zones(Dry Contact Type), the input can be Normal Close(NC), Normal Open(NO),
special for IP Camera alarm output or other wired sensor connection;
Supports verity programmable zone attributes, includesAway(normal), At House or Stay, Entrance
Zone, 24 Hours Sound Zone, 24 Hours Silent Zone, Local Zone, SOS Zone, Door Bell Zone;
The SMS Alarm Content of the digital input is programmable by user through SMS Commands;
Supports Armed delay to give enough time to leave the home, the delay time is programmable by user;
Supports Alarm Delay to give enough time to Disarm it when you come back home, the delay time is
programmable by user;
Equips one siren output for sounding while alarm occurrence to warning;
Equips one Microphone inside, the authorized number can call in to listen onsite or request it call back.
The external AC power failure & recovery alert function supports 2 optional: Immediately Send SMS to
user, after 30 minutes if not recovery then send SMS to user;

Page 5 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
Standby internal large capacity rechargeable battery which can standby upto 8hours afterAC Power
failure, also can provide power to wired siren after AC power failure;
Secure - Using caller ID for identification, unknown callers are ignored;
Supports Password to increase the security of the whole system;
Based on the GSM communication network, no distance limitation.
5. Installation and Connection Diagram
Tips:
a. The backup battery was disconnected, please contact it firstly according to 5.6.
b. After switched on the GSM Dialer, will indicate by a long Di sound,all zones’LED will turn on once, and
the zones which registered wireless sensors, wireless remote control or wireless buttons will turn on once
more.
In the backside of the GSM Dialer, please remove all of the 3 screws, and take the back cover off,
then you can see the PCB. See below:
5.1 Inserting the SIMCard
Important: Make sure to switch off GSM Dialer before inserting or removing your SIM card.
1) Slide the SIM card holder in the direction of “OPEN” (etched on the SIM card holder), and then flip
it open.
2) Insert the SIM card with its gold contacts facing down and its cut-off corner facing out the SIM card
slot. See above photo.

Page 6 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
3) Slide the SIM card completely into the slot. Make sure the SIM card goes through the 2 “guides” on
the SIM card slot.
4) Close the SIM card holder and then slide it in the opposite direction of “OPEN” to lock it. See
above photo.
5.2 Making the Outlets for wires
The GSM Dialer reserved 4 outlets for wires at backside outlets and bottom outlets. The user can
choose the suitable one for different installation requirements. Please use a knife or other tool to
remove the obstacle plastics. Usually, the siren and power supply wires were in one outlets, and the
signal control wires in another outlet to avoid the interference.
Backside Wires Outlet Bottom Wires Outlet
5.3 Contacting the Wired Sensor or IP Camera or Other Alarm Panel to the GSM Dialer
The GSM Dialer equips one dry contact (Normal Close or Normal Open type) digital input port, the
user can connect the IP Camera or CCTV DVR or wired detector or other alarm panel to this port.
When the digital input triggered by IP Camera or CCTV DVR or wired detectors or other alarm panel, it
will alarm.
1) Contacting the wired Detector to GSM Dialer
The wired detector has two connectors, please contact one of them to the DIN port, another
contact to the GND port. And setup the Digital input be the correct NC or NO type by SMS
Commands. (Tips: if you don’t know the NC or NO type of the Detector, please try to change the
setting to NC or NO type by SMS Commands to after you finished connections.)
If you need to contact more than one wired to the GSM Dialer, please ensure all of the wired
detectors are the same output type (Normal Close or Normal Open Types), any one of these
detectors triggered, the GSM Dialer will alarm.

Page 7 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
If the wired detectors are NC type, then the connection must be in series, see below:
if the wired detectors are NO type, then the connection must be in parallel, see above.
2) Contacting the IP Camera or CCTV DVR to GSM Dialer
The user can connect the IP Camera or CCTV DVR Alarm Output to the GSM Dialer’s digital input
as a wired detector, once the IP camera detected intrusion or CCTV DVR alarming, the GSM
Dialer will send SMS to the preset numbers and dial the preset number and make sounds by the
siren. This is very useful for lots of application that need IP Camera and Alarm immediately by
SMS or Dialing. The connection is below:

Page 8 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
3) Contacting the other alarm panel output to GSM Dialer
The user can connect the other Alarm panel’s digital output to the GSM Dialer’s Digital Input as a
wired detector, so the user can update its alarm panel as GSM SMSAlarm. The connection please
reference the DVR or IP Camera.
5.4 Contacting the Siren, hooter
The user can connect one 9~12V rated siren, or hooter to the GSM Dialer’s siren output, once alarm
occurrence, this output ports will start the siren or hooter to make sounds. The positive of the siren
connect to the Siren+ port, and the negative of the siren contact to the Siren –port. Generally, the
siren wire marked red color and black color, the red color is positive and the black color wire is
negative. See below:
5.5 Contacting the Rechargeable Backup Battery
The GSM Dialer equips one rechargeable backup lithium battery that can power on the GSM Dialer for
about 8hours while AC Power goes off. The GSM Dialer will automatically detect the voltage of the
battery, once the voltage lower will charge it automatically. If you are not use the GSM Dialer for lone
time, please remember to disconnect the backup battery. Please install the battery connector to the
socket, please see below:
Notice: Must open the backside cover then you can contact the battery. Once the backup battery turn over, the GSM
Dialer cannot work properly, please contact the external 12VDC to charge it firstly. If you want to replace the battery by
a new one, please note the specification of the backup battery is: 3.7V lithium battery 900~ 1200mA. If long time not use
the GSM Dialer, please disconnect the backup battery to save its lifetime.

Page 9 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
5.6 Contacting the External GSM Antenna
The GSM Dialer equips internal GSMAntenna, usually the GSM Signal is enough to register gsm network
properly. But if the GSM signal is not enough, please replace it by external GSM Antenna from your
distributors or agents. Or take the external GSM Antenna and its connectors to ask any electronic engineer
to replace it, please don’t replace it by yourself, otherwise will damage the GSM Dialer, the enclosure
reserved one hole at the top side, please remove it and fix the external GSM Antenna through this hole.
5.7 Contacting the AC/DC Power Supply
Please contact the +12VDC to the GSM Dialer, the Positive of the +12VDC connect to the PWR+, the
negative of the 12VDC please contact to PWR - . Generally, the red color from theAC/DC Adaptor is
Positive, and the black color is negative. The AC/DCAdaptor is 12V1A or 12V2A. see below:
5.8 Switching on/off the GSM Dialer
After finished all of the connections, please plus theAC/DC Adaptor to externalAC Power socket, and
switch the PSW Switch to ON side to switch on the GSM Dialer. See below:
5.9 Amounting the GSM Dialer

Page 10 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
The GSM Dialer should be installed in a place where the intruders cannot discover it. And the GSM Signal
covered well. Also, the user can see the LED easily to know what happened and what is the status of the
GSM Dialer.
5.10 Reset the GSM Dialer to Factory Default
The GSM Dialer can be reset to the factory default by following operation: Switch off the GSM Dialer, then
press the Reset Button (See below), Switch on the GSM Dialer, about 3Seconds later, the GSM Dialer will
make “Di Di”2 sounds, then loose the RESET button, means the reset operation successful. And please
restart the GSM Dialer.
After this operation, all the registered wireless detectors and wireless panic buttons and Remote Controls
will be removed from the GSM Dialer, and all of the settings will be reset to the factory default.
6. Settings
The GSM Dialer is an advanced multifunctional programmable controller. The user can program it by SMS
Commands for various application requirements.
Notice:
1. The default Password is 1234.
2. All the settings are through SMS commands, please edit the below SMS commands in your cell
phone, then send to the GSM Dialer. (Tips: The GSM Dialer cannot support PIN Code Protected
SIMCard. Please ensure you have disabled the PIN Code of the SIMCard, otherwise can not
register GSM Network successful.)
3. You can program the GSM Alarm & Dialer GSM Dialer with SMS commands using your phone. It
is safe to do so because in addition to the fact that other people may not know the number of the
SIM inserted in it, we also use a Password that makes it impossible for anybody, who doesn't
know it, to access the system by chance.
4. Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap etc.
Don't add spaces or any other character.
5. The pwd in the commands is means the password, when you use it, please in stand of it by the
digital number.
6. In some GSM operators, they use different SMS parameter, the units can’t return the SMS
confirmation is normally. It is not product problem. Also, you can try to add the country code
before the number, because of every GSM Operator will automatically plus the country code
while send SMS or receive SMS or dialing, the format is not the same for dial and SMS. if some
functions can not work, then please setup include country code or remove country code for

Page 11 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
different functions. see the below settings:
7. If the command is incorrect, the GSM Dialer will return: SMS Format Error, Please check Caps
Lock in Command! Or other warning message. So please check the Command, or check the
input is in ENGLISH INPUT METHOD and CAPS LOCK. If the password incorrect will not return
any SMS.
8. If more than 2 minutes the GSM Simcard still register the GSM Network failure, the buzzer will
make “Di”once, and every 10 seconds detects the SIMCARD registering status and failure will
alert by “Di”once till restart or switch off.
9. If the communication between the MCU and GSM Module failure, the buzzer will make “DiDi”
twice to warning every 10 seconds till switch off or restart.
10. If detect the GSM Dialer hasn’t inserted SIMCard, the Buzzer will only make once di sound to
alert. And will not detect the SIMCard again.
11. When alarm occurrence and in the delay alarm time, the buzzer will alert by “DiDi”sounds, once
the delay timeout the buzzer will stop to sound.
12. Reset the GSM Dialer will alert by a 2seconds “Di”sound by the buzzer.
13. After you reset please remember to restart it, otherwise, can not work proplerly.
14. The SMS commands that you will certainly use in the GSM Alarm & Dialer GSM Dialer are the
following:
6.1 Setup New Password
if successful, the unit will return: new password,This is the New Password, please remember it
carefully. The password is 4digits.
For example, the original password is 1234, you want change it to 6666, then you can send the command
below: 1234P6666
For example:
In China, the country code is 0086, or +86.
The user cell phone number is 13500001111 and has been assigned as a SMS Alert number, the simcard
number in the panel is 13512345678.
Problem 1: Alarm but the user hasn’t received the SMS Alert.
Solution: Please plus the country code while you setup the 13500001111 as SMS Alert number, means setup
008613500001111 or 8613500001111 to instead of the 13500001111.
Problem 2: The user number can receive the SMS Alert message from alarm panel, but the alarm panel can
not receive the commands from the user number.
Solution: Please add country code to the simcard number in the alarm panel. Means send sms commands to
008613512345678 or 8613512345678 to instead of 13512345678.
Solution 3: When you use cell phone dial another one, what number it will be displayed then you can set the
displayed number as dial numbers; when you use cell phone send SMS to another cell phone, what number it
will be displayed then you can set the displayed number as SMS Alert number, just use the 00 to replace the
“+”, also, you can try the “+”.
pwd+P+newpassword

Page 12 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
6.2 Setup Authorized number(If you GSM Operator use different number format for SMS and Dial out,
then please see Notice 6, must setup as includes country code and not includes country code two
formats.)
Pwd is the password, default is 1234.
Serial Number = 1~6.
Ais the identification character of this command.
Function 1 Code =1,2,3. It is for alarm receiving attribute setting.
=1 stands for when alarm occurrence, the GSM Dialer will dial as well as send SMS to this number.(The
SMS Number Format must be the Same as the Dial Number Format, include or not includes Country
code.)
=2 stands for when alarm occurrence, the GSM Dialer only send alarm SMS to this number, doesn’t dial.
=3 stands for when alarm occurrence, the GSM Dialer only dial this number, doesn’t sends SMS.
Function 2 Code =1,2,3. It is for accessing GSM Dialer attribute setting.(For monitoring Power function,
please set the function 2 code =3)
=1 stands for when this number dial to the GSM Dialer, will be rejected after the first ring, meanwhile, the
GSM Dialer will be changed to Stay Mode and not return SMS. This is very useful when the user come
back home or office to change the GSM Dialer to Stay mode with a FREE call from its mobile phone!
When the user leave the home or store or office, dial the GSM Dialer again, the GSM Dialer will be
changed to away armed mode and return SMS: Armed to ensure the armed operation is successful.
Tips: When any number with this value call in the GSM Dialer, the GSM Dialer will change from Stay to Armed or Armed to
Stay, if the GSM Dialer in Disarmed mode, then the first time call in will change the GSM Dialer to Stay mode.
=2 stands for when this number dial to the GSM Dialer, will be picked up automatically and enter into listen
mode, the user can listen on-site sounds or noise immediately through the GSM Dialer’s microphone. (This
function available after 2014-03-15)
=3 stands for this number cannot access the GSM Dialer by dial in, will be hang up. Nor listen neither
change to Stay or Arm Mode.
Telephone Number: authorized number, max. 18 characters,
E.g.: if you want to setup 13512345678 as the third authorized number, and the password is 1234, country
code is 0086, when alarm occurrence this number can receive both SMS and incoming from the GSM
Dialer, when dial to the GSM Dialer from this number, will refuse. Then you can send
12343A1#3#008613512345678# to the GSM Dialer. Will return:
6.3 Inquiry the Authorized number
Tel1: Empty
Tel2: Empty
Tel3: 008613512345678-1-1 -1-1stands for function 1 code =1 and function 2 code =1 value.
Tel4: Empty
Tel5: Empty
Tel6: Empty
Pwd+Serial Number+A+Function 1 Code+#+Function 2 code+#+Telephone Number+#
pwd+A+#

Page 13 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
After received this command,the GSM Dialer will return the SMS as abovementioned.
E.g.: If you want to know the authorized number list, and the password is 1234, then you can send 1234A#
to check it.
6.4 Remove the Authorized Number
Please overwrite it with another number that you wish to change it or removed it by SMS Command.
6.5 Modify the wired zone dry contact digital input type (Default is NC)
Modify the digital input to NC (Normal Close) type, if the sensor you used with this unit is NC, then you
should set the unit as NC type.will return : Zone00 NC.
Modify the digital input to NO (Normal Open) type, if the sensor you used with this unit is NO, then you
should set the unit as NO type. will return: Zone00 NO.
6.6 Modify the SMS Alarm Content
If setup successful, will return the SMS Alarm Content.
Bis the identification character of this command.
Zone Number=00, 00 stands for the wired zone.
SMS Alarm Content: When alarm occurrence, the GSM Dialer will send the SMS Alarm Content to the
authorized numbers by SMS. Max. 40 characters.can not be empty, otherwise the GSM Dialer will return :
SMS Alarm Content cannot be set as empty!
E,g.: if you want to receive SMSAlarm content of the wireless zone 00 is intruder breaking the windows,
and password is 1234, then you can send SMS 1234B00#intruder breaking the windows#.
6.7 Inquiry the SMS Alarm Content Setting
If setup successful, will return the zone number’s SMS Alarm Content.eg.: 1234B00#.
6.8 Setup the Zone Attribute
If setup successful, will return the zone number’s Attribute code.
Dis the identification character of this command.
Zone Number=00, 00 stands for the wired zone.
Attribute Code=0~9, stands for how does the GSM Dialer will performance when this zone activated.
=0, stands for entrance, when armed the GSM Dialer, this zone will delay 30 seconds to enter into Armed
mode, for leaving the home or office. When come back the home or office, will delay 20 seconds to
alarm in order to the user can change it to Stay or Disarm the GSM Dialer.
pwd+NC+#
pwd+B+ZoneNumber+# +SMS Alarm Content+#
pwd+B+00+#
pwd+D+Zonenumber+#+Attribute Code+#
Pwd+NO+#
pwd+Serialnumber+A+#

Page 14 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
=1, stands for outer zones , inArmed or Stay mode, when triggered will cause alarm.
=2, stands for inner zones, in Stay mode if triggered will not cause alarm; in Armed mode, if triggered will
cause alarm.
=3, stands for spot alarm zone, in Stay mode if triggered only cause the siren to sound. Neither dial out nor
send SMS out; in Armed mode if triggered will cause alarm.
=4, stands for 24hours emergency zone with sounds. In any mode if triggered will cause alarm
immediately with siren sounds.
=5, stands for 24hours emergency silent zone. In any mode if triggered will cause alarm immediately, the
siren will not sound.
=6, stands forArmed Button, trigged it to make the GSM Dialer change toArm Mode.
=7, stands for Stay Button, triggered it to make the GSM Dialer change to Stay Mode.
=8, stands for Disarm Button, triggered it to make the GSM Dialer change to Disarm mode.
=9, stands for door bell button, triggered it to cause the buzzer to sound 8times.
Tips:
1) When the attribute code setup as 6,7,8,9, the siren will not sound.
2) e.g.: if want to setup the attributes of wired zone as =5, stands for 24hours emergency silent zone, the
password is 1234, then please send 1234D00#5#
6.9 Setup the Siren Sound time(Default is 180seconds)
If setup successful, will return Siren ON + xxx + Seconds
Eis the identification character of this command.
Xxx=000~999, unit is second, 3 digits. Default is 180 seconds.
E,g,: if you want to setup the siren sound 60seonds when alarm occurrence, and password is 1234, then
please send 1234E060#
Tips:
Only the zone attribute code setup as 0,1,2,3,4 will cause the siren sound while alarm occurrence. And the siren will
sound about 20 seconds then interrupt about 2 seconds,
6.10Setup the Alarm Delay Time(Default is 000second)
If setup successful, will returnAlarm Delay + xxx + Seconds
Fis the identification character of this command.
Xxx=000~999, unit is second, 3digits. Default is 000 second.
Tips: Only the zone attribute code setup as 1,2,3 will delay to cause alarm while alarm occurrence.
6.11Setup the Arm Delay Time(Default is 30seconds)
If setup successful, will returnArmed Delay + xx + Seconds
Gis the identification character of this command.
Xxx=00~99, unit is second, 2digits. Default is 30 seconds.
Tips:
pwd+E+xxx+#
#
pwd+F+xxx+#
#
pwd+G+xx+#
#

Page 15 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
1) Only the zone attribute code setup as 1,2,3 will delay to enter into Arm mode when Arm the GSM Dialer;
2) If Armed the GSM Dialer by remote control, after press the Armed Button, and press its SOS button within 2 Seconds
the GSM Dialer will enter into Armed Mode immediately, will not delay.
6.12Enable to Alert the first Authorized Number when other number armed or disarmed the GSM
Dialer(Default is Disable)
If setup successful, will return Send Operation Code to 1st Number
His the identification character of this command.
Tips: If enable this function, when the Authorized Number that Function 2 Code=1 (can dial in to change the status from
Stay to Arm) call in the GSM Dialer, will send SMS to the 1st Authorized Number. If any other number armed or disarmed the
GSM Dialer, it will send SMS to the 1st Authorized number. The SMS content is Armed By + Telephone number or
Disarmed by +Telephone number.
Disable this function SMS Command is pwd+J+#
6.13 Required the GSM Dialer callback(This function available after 2014-03-15)
If send successful, the GSM Dialer will call back the user immediately. It is special for the Authorized
Number that Function 2 Code=1 (can dial in to change the status from Stay to Arm) to listen on-site.
6.14 Setup External Power Status Alert Feature(Default is 30 minutes)
If send successful, will return SMS.
Mis the identification character of this command.
Xx= 00~99. Default is 30. Unit is minute
Xx=00, stands for when externalAC Power goes off will send SMS AC Power Goes off to all authorized
numbers or send SMS AC Power Goes ON whenAC Power goes on. If setup successful, will return AC
Power Goes off Send SMS Immediately.
Xx=01~99, stands for when external AC Power goes off more than 01~99 minutes will send SMS AC
Power Goes off 01~99minutes to all authorized numbers or send SMS AC Power Goes ON when AC
Power goes on. If theAC Power goes off less than 01~99 minutes then goes on, will not send SMS. If
setup successful, will return AC Power Goes off Send SMS After 01~99minutes.
6.15Setup Siren Response Feature to Arm Operation
If send successful, will return SMS.
Xx= ON or xx=OFF. Default is off.
Xx=ON, stands for when armed the GSM Dialer by remote control successful, the siren will sound
2seconds. If setup successful, will return Set Ok.
Xx=OFF, stands for when armed the GSM Dialer by remote control successful, the siren will NOT sound. If
setup successful, will return Set Ok.
Tips: if armed or disarmed by phone call or SMS, the siren will not make sounds to response.
6.16Setup Automatically report Status function
pwd+H+#
#
pwd+K+#
#
pwd+M+xx+#
#
pwd+xx+#
#

Page 16 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
XX=00~99, unit is hour, stands for the interval time to report the GSM Dialer status to the first SMSAlert
Number. default is 00, means disable report function. If no SMS number, this function will be invalid. The
return SMS is the same as by 7.4 Inquiry Status and GSM Module IMEI Code
7. Operating Instructions
Tips!
1. The user can arm/disarm/Stay (Partial armed) by Dial in, and, SMS, Another, the user can switch on or off the Siren
by SMS Commands.
2. Mode explanation
Armed: Away, In this mode, any detector triggered will cause alarm. It be used for away the home and need to
protect all of the home or office or store,etc.
Stay: Partial armed, at home, in this mode, only the outer zones and emergency zones triggered will cause alarm,
the inner zone triggered will not cause alarm. It be used for partial armed, e.g.: some people at home, and need to
monitoring the outer security.
Disarmed: Except the 24 Hours emergency zones triggered will cause alarm, all of the other zones triggered will
not cause alarm. Usually for maintain or other special requirements.
3. Alarm Occurrence
1) When alarm occurrence, the GSM Dialer will send out Alarm SMS Content firstly, then automatically dial the
authorized numbers one by one, if picked up the call, the GSM Dialer will stop to sound and enter to listen
mode, can not speak. If nobody picked up or rejected, the GSM Dialer will dial all of the authorized numbers 3
times in cycle then stop to dial any more. Meanwhile, the GSM Dialer will enter to previous status.
2) Only the zone attribute code setup as 0,1,2,3,4 will cause the siren sound while alarm occurrence. And the
siren will sound about 20 seconds then interrupt about 2 seconds, the time according to the setting.
3) Once any zone triggered, the corresponding LED will always on till Disarm or Restart the GSM Dialer.
7.1 Armed or Stay WITH a FREE call from authorized phone!
The GSM Dialer supports armed or Stay by a free call from authorized phone, after you setup the
authorized number Function 2 Code as 1, then the user can use this phone number to Arm or Stay the
GSM Dialer by free charge call in. Please reference 6.2 Setup Authorized Number to setup it.
When the GSM Dialer in Disarmed mode, any number with the authorized right call in will change it to
Stay mode;
When the GSM Dialer in Stay Mode, any number with the authorized right call in will change it to
Armed(Away) mode, and return SMS confirmation Armed.
When the GSM Dialer in Armed(Away) Mode, any number with the authorized right call in will change
it to Stay Mode.
This function is very useful while you leave or come back home.
7.2 SMS Commands for Arm(Away) or Disarm or Switch On/Off Siren.
The User canArm/Disarm/Switch on or off the siren by sending SMS to the GSM Dialer. The SMS
Commands are below:
Notice:
The system will carry out the commands immediately (with no delay) after the GSMDialer receive this SMS command.
7.2.1 Armed(Away)
pwd+T+xx+#
#

Page 17 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
7.2.2 Disarm
7.2.3 Switch On the Siren
7.2.4 Switch OFF the Siren
7.3 Inquiry Status and GSM Module IMEI Code
7.4 iOS App and Android Apps Instructions
The user can operate the GSM Dialer byAndroid Apps and iOS. Both of them are free charge. For
AndroidApps, please download from our official website, and download the iKeyPad fromApple Store.
The interface of these tools please see below.
xxxxEE
“xxxx”stands for the password (4 digits).
Return SMS
Armed or Disarmed
AC Power ON or AC Power off.
GSM Value is 17 or other value
IMEI Code: xxxxxxxxxxxxxxxxxx
Example
1111DD
When the Password is 1111
xxxxDD
“xxxx”stands for the password
(4 digits).
Return SMS
Siren OFF.
Example
1111CC
When the Password is 1111
xxxxCC
“xxxx”stands for the password
(4 digits).
Return SMS
Siren ON.
xxxxAA
“xxxx”stands for the password
(4 digits).
Return SMS
Armed
Example
1234AA
When the Password is 1234
Example
1111BB
When the Password is 1111
xxxxBB
“xxxx”stands for the password
(digits).
Return SMS
Disarmed

Page 18 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
8. Technical specifications
Rated Voltage: 12VDC 2 A (12V~14VDC)
Standby Consumption: 30~35mA (Not charging battery)
Working Consumption: 400mA(Siren working)
Working temperature: -10℃～+60℃
Storage temperature: -20℃～+60℃
Relative humidity: 10-90%, No condensation
GSM frequency: 900/1800MHz(Default) or 850/1900Mhz (Optional)
Communication protocol: GSM PHASE 2/2+ (include data service)
Wired Zones: 1 (Dry Contact, NC or NO)
Backup Rechargable Battery: 3.7V@900~1200mAH lithium batteries
Net Weight: 0.50Kg
9. Maintenance
1) In case of failure, please contact the distributor or manufacturer.
2) If the remote control works, but the GSM Dialer fails to send SMS texts, switch the power of GSM
Dialer off and switch it on after one minute. Test this system after another minute, or check the
settings are correct and the GSM Signals are strong enough.
3) If the GSM Dialer can run and sensors work, but cannot send SMS texts, please change SIM Card to
check it.
4) If the problem cannot be solved, please contact the distributor or manufacturer.
10. Warranty
1) This system is warranted to be free of defects in material and workmanship for one year.
2) This warranty does not extend to any defect, malfunction or failure caused by abuse or misuse by the
Operating Instructions. In no event shall the manufacturer be liable for any alarm system altered by
purchasers.
11. Affix Table
Table 1. GSM Dialer Installation Schedule
Before install the GSM Dialer, please write down the installation plan firstly, it is very useful for saving your
test and installation time.After installed successful, then tear down this Schedule for review in further.

Page 19 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
GSM Dialer Authorized Number Schedule
SIMCard Number in the GSM Dialer: ___________________
Serial
Number
User Name
Phone Number
Authorized Type
Alert when Alarm Occurrence
Access the GSM Dialer
SMS&Call
SMS
Call
Stay/Arm
listen
Refuse
1
2
3
4
5
6
Notice: Please mark V if for enable and X for disable.
Table 2. GSM Dialer Program and Operation SMS Command List
GSM Dialer SMS Command List(Caps Lock)
S.N.
Function Description
SMS Command Format
Example
1
Arm(Away)
pwd+AA
1234AA (Password is 1234)
2
Disarm
pwd+BB
1234BB (Password is 1234)
3
Switch On The Siren
pwd+CC
1234CC (Password is 1234)
4
Switch OFF the Siren
pwd+DD
1234DD (Password is 1234)
5
Inquiry Status,GSM Signal, IMEI
pwd+EE
1234EE (Password is 1234)
6
Setup New Password
pwd+P+newpassword+#
1234P6666.
7
Setup Authorized number
pwd+Serial Number+A+Function 1 Code+#+Function 2
code#Telephone Number+# [See 6.2]
8
Inquiry the Authorized number
pwd+A+#
9
Remove Authorized Number
pwd+SerialNumber+A+#
10
Modify wired zone type as NC
pwd+NC+#
Default is NC
11
Modify wired zone type as NO
pwd+NO+#
12
Modify the SMSAlarm Content
pwd+B+ZoneNumber+#+ SMS
Alarm Content+#
1234B00#intruder
breaking the windows#
13
Inquiry the SMS Alarm Content
pwd+B+Zonenumber+#
1234B00#
14
Setup the Zone Attribute
pwd+D+00+#+Attribute Code+# [See 6.8]
15
Setup the Siren Sound time
pwd+E+xxx+#
1234E060#,(Default:180S)
16
Setup theAlarm Delay Time
pwd+F+xxx+#
1234F999#,(Default:000S)
17
Setup theArm Delay Time
pwd+G+xx+#
1234G09#,(Default: 30S)
18
Enable Alert the 1st Authorized No.
pwd+H+#
19
Disable Alert the 1st Authorized No.
pwd+J+#
Default
20
Required to callback
pwd+K+#

Page 20 of 20 Ver 1.1
GSM SMS Voice Alarm Dialer
GSM Power Monitoring Alarm
21
AC Power Goes OFF Alert at once
pwd+M+00+#
22
AC Power Goes OFF Alert after
01~99 minutes
pwd+M+xx+#
Default is 30minutes
23
Siren Response to Arm Operation
pwd+ON+#
Default
24
Siren NOT Response to Arm
Operation
pwd+OFF+#
25
Automatically report Status function
pwd+T+xx+#
00～99hours,default is 00,
means disabled.
The End!