King Tony 44704 Troubleshooting guide

44704MP
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
Cordless Impact Wrench
1
1
BL1 8DS
AND INSTRUCTION MANUAL
Brushless Drill Driver
BRUSHLESS IMPACT DRIVER
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
NO.44614MP
Enjoy your work
CORDLESS IMPACT WRENCH
44704

SAFETY INSTRUCTIONS
WARNING: Read all safety warnings and all instructions.
1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs and, matching outlets will reduce risk of electric
shock.
2. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or on explosive atmospheres.
4. Disconnect the plug from the power source before making and adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting the power tools accidentally.
5. Store idle power tools out of the reach of children
6. Maintain power tools. Check for misalignment of binding of moving parts, breakage of parts and any
other condition that may affect the power tools operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
7. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
8. When battery pack is not in use, keep it away from other metal objects that can make a connection from
one terminal to another. Shorting the battery terminals together may cause burns or a fire.
9. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
10. Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required.
Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of
fire, electric shock, or injury to persons
11. To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this risk.
12. Do not place any object on the top of the charger as it could cause overheating.
13. Pull on the charger to disconnection it from the power source. Do not pull on the lead.
14. Never recharge a fully charged battery. Overcharging shortens the battery service life.
15. Do not charge at voltage higher than indicated as charger specification; otherwise, the charger will burn
up.
2

CHARGER INDICATOR & BATTERY INSTALLATION
Suitable charging environment:
Charging temperature: 0°C ~40°C (32°F~104°F)
Discharging temperature: 0°C ~40°C (32°F~104°F)
Storage temperature: -20°C ~60°C (-4°F~140°F)
Storage humidity: 70%RH
The indicators of the charger
RED Power On The charger is power on
Battery at High
Temperature
The battery pack is overheated. Please wait until the
battery pack cools down, or take it out from the charger
temporarily to be cooled off.
Battery at Low
Temperature
The battery pack’s temperature is too low. Please wait
until the battery pack’s temperature rises. Please wait
until the pack’s temperature rises to 0°C.
YELLOW
Incorrect battery
type or Battery
no good
Please replace the battery pack with a new one.
Fast Charging The battery is under quick charging
GREEN Fully Charged The charging is completed.
WARNING
If any of the following occurs, unplug the charger from the power supply outlet and replace the battery pack
None of the indicators lights on illuminate at all.
The yellow indicator light glitters constantly.
Only the red indicator light is on even if the battery pack
Battery Pack Charging Installation
Slide direction
LED indicator
3

EXPLANATION OF GENERAL VIEW
Handle Carbon brush cap
Front Cover
Shaft
LED light
Terminal
Trigger Strap
Forward/Reverse lever
Grip
Battery power indication
Batter
y
Pack
Bottom
SPECIFICATION
Charger18V Cordless Impact Wrench
Model 44704MP
Voltage DC 18V
Un Loaded Speed 0~2000 rpm
850 Nm(625ft-lb)
Max Torque
650 Nm(480ft-lb)
Weight
(with 4.0Ah battery) 2.62 Kg
Input Voltage AC 100-240V 50/60 Hz
Output Voltage DC 21V 3.0A
Charging Time 45 min for 2.0Ah battery
60 min for 4.0Ah battery
Battery pack
Voltage 18V
Capacity Cell Type 2.0Ah & 4.0Ah Li-ion
OPERATING INSTRUCTIONS
Remove
Installing
Battery Pack Installation
Double check battery pack was well installed,
heard “click” sound and there no gap
between the tool and pack housing.
4
Working Torque

Operating Procedure
5
Installing or removing socket Installing
Make sure it will not come off if the socket is lightly pulled. Remove
Trigger action and Lighting up the LED light
1：When the switch is depressed, the tool rotates.
When the switch is released, the tool stops.
2：The rotational speed can be controlled by varying the amount
that the switch is pressed. Speed is low when the switch is pressed
slightly and increases as the switch is pressed more.
3：The LED will light when you depress the switch.
**Do not face to the tool when the tool is rotating.
Forward/reverseswitchlever
(R) (L)
This tool has a forwarding/reversing switch lever
to change the direction of rotation.
**When not operating the tool, always set the forwarding/reversing switch lever to the neutral position.
Installing and removing the handle
**Make sure the tool is stopping rotate before installing or removing the handle.
Replacing carbon brushes
Remove and check the carbon brush regularly. Replace when they wear
down to the limit mark (5mm). Both carbon brushed should be replaced
at the same time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take out the worn
carbon brushes, insert the new ones and secure the brush holder caps.
Installing
Remove
Reverse Forward Lock
Depress the reversing switch lever “R” for
clockwise rotation or “L” for counterclockwise
rotation.

K
K
KI
I
IN
N
NG
G
GT
T
TO
O
ON
N
NY
Y
YT
T
TO
O
OO
O
OL
L
LS
S
SC
C
CO
O
O.
.
.,
,
,L
L
LT
T
TD
D
D.
.
.
No11, 150 Alley, 516 Lane, 2 Sec., Hsi Nan Rd.,
Wu-jih shiang, Taichung Hsien, Taiwan, R.O.C.
Tel:[phone] Fax:[phone]
http://www.kingtony.com
EU DECLARATION OF CONFORMITY
FOR NON-ANNEX IV MACHINERY
IN ACCORDANCE WITH
MACHINERY SAFETY DIRECTIVES
2004/108/EC
WE, KINGTONY TOOLS CO., LTD. HEREBY CERTIFY THAT THE MACHINERY DESCRIBED BELOW
CONFORMS WITH EMC DIRECTIVES 2004/108/EC ON THE APPROXIMATION OF THE LAWS OF THE
MEMBER STATES RELATING TO THE SAFETY OF MACHINERY,
PRODUCT NAME : RECHARGEABLE CORDLESS IMPACT WRENCH
MODEL S: 44704MPA、44704MPB、44704MPD
AND COMPLY WITH THE PROVISIONS SET OUT IN THE FOLLOWING STANDARDS:
FCC CFR 47, Part 15 SubpartB/ CISPR 22 3rd Edition: 1997, Class B
ANSI C63.4:2009
Canadian ICES-003 issue 5(2012)
EN55014-1:2006+A1:2009+A2:2011
EN55014-2:1997+A1:2001+A2:2008,IEC 61000-4 Series
AS/NZS CISPR 14.1:2013
DATE OF ISSUE: 10th November 2015
NAME: Lin Hsien-Wen
POSITION/TITLE: GENERAL MANAGER
SIGNATURE:
6
8
44704MPA,44704MPB,44704MPD
44704MPA01,44704MPB01,44704MPD01
AND COMPLY WITH THE PROVISIONS SET OUT IN THE FOLLOWING
EUROPEAN STANDARD:
FCC CFR 47, Part 15 SubpartB/ CISPR 22 3rd Edition: 1997, Class B
ANSI C63.4:2009
Canadian ICES-003 issue 5(2012)
EN55014-1:2006+A1:2009+A2:2011
EN55014-2:1997+A1:2001+A2:2008,IEC 61000-4 Series
AS/NZS CISPR 14.1:2010

7
INDEX REQ'D INDEX REQ'D
NO. NO. NO. NO.
1038431-A01 Handle grip 129 038431-A29 Motor 1
2038431-A02 Screw plugger 230 038431-A30 LED 1
3038431-A03 Torx screw 431 038431-A31 Heat shrink tube 2
4038431-A04 Protection cover 132 038431-A32 Resistor 1
5038431-A05 Front cover 133 038431-A33 Heat shrink tube 1
6038431-A06 Bushing 134 038431-A34 Heat shrink tube 1
7038431-A07 Washer 135 038431-A35 Forward / Reverse lever 1
8038431-A08 Anvil ring 136 038431-A36 Thermostst 1
9038431-A09 O-ring 137 038431-A37 Trigger 1
10 038431-A10 Shaft 138 038431-A38 PC Board 1
11 038431-A11 Steel ball 239 038431-A39 Screw 2
12 038431-A12 Hammer 140 038431-A40 Contactor cover 1
13 038431-A13 Steel ball 20 41 038431-A41 Terminal 3
14 038431-A14 Washer 142 038431-A42
Contactor seat 1
15 038431-A15 Spring 143 038431-A43 Strap 1
16 038431-A16 Spring seat 144 038431-A44 Housing (bottom) 1
17 038431-A17 Lock ring 145 038431-A45 Housing (top) 1
18 038431-A18 Transmission shaft 146 038431-A46 Torx screw 10
19 038431-A19 Planet gear 247 038431-A47 Magnet ball 1
20 038431-A20 Solid pin 248 038431-A48 Carbon brushes 2
21 038431-A21 Washer 149 038122P04 4.0Ah battery 1
22 038431-A22 Gear ring stopper 150 038122P02 2.0Ah battery 1
23 038431-A23 O-ring 151 038122P03A Charger 1
24 034831-A24 Gear ring 1TK1 044704-ATK1
25 034831-A25 Needle bearing 1TK2 044704-ATK2
26 034831-A26 Hex screw 2TK3 044704-ATK3
27 034831-A27 Gear box 1TK4 044704-ATK4
28 034831-A28 Motor gear 1TK5 044704-ATK
44704MPA Europe 44704MPA01 Europe
44704MPB America/Asia 44704MPB01 America/Asia
44704MPD Australia&
New Zealand 44704MPD01 Australia& New Zealand
20160102R1
1/2" DR. CORDLESS IMPACT WRENCH
KT No. DESCRIPTION KT No. DESCRIPTION
Output Shaft Group ( incl.4.5.6.7.8.9.10 )
Shaft Group
(incl.11.12.13.14.15.16.17.18.19.20 )
Motor Group ( incl.28.29 )incl 4pcs
Capacitance/Heat shrink tube
Switch Group
(incl 30.31.32.33.34.36.37.38.39.40.41.42.47)
Gearbox Group(incl.22.23.24.25.26.27 )
2.0Ah battery*1
4.0Ah battery*1
18V2.0 Charger
4.0Ah battery*2
18V4.0 Charger
R
ITEM NO. 44704MPA
44704MPB
44704MPD
44704MPA01
44704MPB01
44704MPD01


customerservicee‐mail:[e-mail]