King Young Sumicom S675E User manual

Barebone System Unpacking Guide
Install CPU and CPU Cooler
Install Memory
Complete
INSTALLATION GUIDE
1
2
3
Install CPU into CPU socket. Match socket pin 1 and
CPU cut edge. Screw down the black button to fasten
the CPU.
Glue the heatsink compound on the CPU die surface.
Install CPU cooler on top of CPU. Tighten CPU cooler
with screws into pillaret.
Connect CPU FAN connector to mainboard CPU
FAN socket.
1
2
Insert SODIMM into the SODIMM slot
on the motherboard by 30 .
0
Push down the SODIMM.
SODIMM
SODIMM Slot
2
B1
B5
A1 GigaLAN Port
A1 GigaLAN Port
A2 Two USB 2.0 Ports
A2 Two USB 2.0 Ports
A3 PS/2 Mouse Port
A3 PS/2 Mouse Port
A4 PS/2 Keyboard Port
A4 PS/2 Keyboard Port
A5 RS232/COM 1 Port
A5 RS232/COM 1 Port
A6 VGA Port
A6 VGA Port
A7 DC 12V Power In
A7 DC 12V Power In
A8 Line-Out Port
A8 Line-Out Port
A9 4 Lane PCIe Riser Card
A9 4 Lane PCIe Riser Card
A10 Optional DVI-D Port
A10 Optional DVI-D Port
Specifications are for reference only and subject to change without notice.
Mainboard and PCIe Riser Card Layout
1
A1
A2
A4
A3
A6 A5
A7
A8
M1675E
Item Checklist
B1 Mic-In Phone Jack
B1 Mic-In Phone Jack
B2 Power/HDD LED
B2 Power/HDD LED
B3 Power Button
B3 Power Button
B4 Reset Button
B4 Reset Button
B5 Ear Phone Jack
B5 Ear Phone Jack
B6 Four USB 3.0 Ports
B6 Four USB 3.0 Ports
B7 Optional GigaLAN Ports
B7 Optional GigaLAN Ports
Standard S675 Rear IO Ports
1 Secondary COM Port Header
1 Secondary COM Port Header
2 CPU Socket
2 CPU Socket
3 4 Lane PCIe Riser Card Slot
3 4 Lane PCIe Riser Card Slot
4 Intel Giga LAN Chip
4 Intel Giga LAN Chip
5 SODIMM Slots
5 SODIMM Slots
6 Intel HM76 Chip
6 Intel HM76 Chip
7 Super IO Chip
7 Super IO Chip
8 CPU Cooling Fan Connector
8 CPU Cooling Fan Connector
9 SATA DVD-ROM Drive Cable
9 SATA DVD-ROM Drive Cable
10 CMOS Battery
10 CMOS Battery
11 SATA HDD Connector
11 SATA HDD Connector
12 Buzzer
12 Buzzer
1
2
3
CPU
CPU
Socket988
FAN
Socket
CPU Cooler
Screw
Close Open
*CPU install notice
180
0
1
2
2
4
6
9
11
8
1
10
3
B6
B6
B4 B3 B2
A10 Model S675T/S675G3 Rear IO Ports
Standard S675 Front IO Ports
5
12
7
Heatsink
4 Lane PCIe
Riser Card
A9
A9
A9
1
2
Loose the screws on the rear panel from the case.
Pull out the mainboard from the case.
21
1
1
SILICONE HEAT
SINK PASTE
SILICONE HEAT
SINKPASTE
INK PAS
CPU Cooler
System Unit
PU Sponge
Accessory Pack
Power Adapter
Power Cord
Installation
Guide
Driver DVD
Optional DVI-D
Daughterr Board
A10

Part List STEP 1
DVD-ROM Drive Screws (* 5)
Case Screws (* 2)
M
J
EMI Sticker (*2)
Rubber Stand (*4)
L
O
K
Install Slim HDD
STEP 2
Install DVD-ROM Drive
M1675E
CPU Cooler Screws (* 2)
P
Accessory Pack
L
DVD-ROM Drive
Bracket
A
B
C
D
2.5" HDD Screws (* 5)
E
COM/DVI Screws (* 6)
Front Panel
Rear Panel
Case
2
3
180
0
Turnover the Mainboard.
2
3
Q
CPU Cooler Paste (* 1)
T
SINKPASTE
SILICONEHEAT
SINKPASTE
INKP
AS
INSTALLATION GUIDE
Mainboard
F
B
HDD
1
1
Install HDD attach to Drive Adapter.
**Notice:The HDD's label side is up.
CD-ROM drive
B
J
M
Paste EMI Stickers oo the top of the DVD-ROM drive.
Connecting onboard SATA cable to the DVD-ROM drive.
1
3
2
3
2
1
Tighten DVD-ROM drive with screws to the DVD-ROM
drive braket.
2
CPU Cooler
G
Hardware Installation
Optional DVI-D
Daughter Boards
I
The system uses entire case for
partial heat dissipation, so the
normal operating temperature
of the case is between 40 C ~ 50 C.
Specification is subject to change without notice, it is for reference only.
Tighten HDD with screws to the Mainboard.
4 Lane PCIe
Riser Card
H
WARNING
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protction against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance with
the instruction manual may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio TV technician for help.
Notice: The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equivalent.
Complete System
Install Case
Install mainboard into the case.
1
Tighten rear panel with screws to the case.
2
Stick the rubber stand.
3
O
K
1
3
2
STEP 3
Install PCI-E Card
Install PCI-E Card into the PCI-E Slot.
1
Tighten PCI-E Card and rear panel with the screw.
.
2
1
4 or 1 Lane PCI-E Card
Note: The length of PCI-E card not longer than 8.5 inch (220mm).
2
N
4 Lane PCI-E Riser Card
H
PCIe Card Fasten Screws (* 1)
N