Kingston Technology Locker+ User manual

DataTraveler®Locker+ User Manual
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 1 of 22

Document No. 48008071-001.A02 DataTraveler®Locker+ Page 2 of 22
Table of Contents
About This Manual .................................................................................................................. 3
System Requirements............................................................................................................. 3
Recommendations .................................................................................................................. 3
Setup (Windows Environment)............................................................................................... 4
Device Initialization (Windows Environment) ....................................................................... 5
Device Usage (Windows Environment) ................................................................................. 9
Device Options (Windows Environment)............................................................................. 10
Setup (Mac Environment) ..................................................................................................... 12
Device Initialization (Mac Environment).............................................................................. 13
Device Usage (Mac Environment)........................................................................................ 17
Device Options (Mac Environment) ..................................................................................... 18
Help and Troubleshooting.................................................................................................... 20
Device Lockout.........................................................................................................................20
Forgot Password......................................................................................................................21
Drive Letter Conflict (Windows Operating Systems)............................................................22

About This Manual
This user manual covers the DataTraveler®Locker+ (referred to simply as DTL+ from this point
forward) based on the factory image with no implemented customizations.
System Requirements
PC Platform
•Pentium III Processor or equivalent (or
faster)
•15MB free disk space
•USB 2.0
•Two consecutive drive letters after the
last physical drive*
PC Operating System Support
•Windows®7
•Windows®Vista SP1, SP2
•Windows®XP SP2, SP3
Mac Platform
•15MB free disk space
•USB 2.0
Operating System Support
•Mac OS X 10.5.x
•Mac OS X 10.6.x
Recommendations
To ensure there is ample power provided to the DTL+ device, insert it directly into a USB port
on your notebook or desktop, as seen in Figure 1.1. Avoid connecting the DTL+ to any
peripheral device(s) that may feature a USB port, such as a keyboard or USB-powered hub, as
seen in Figure 1.2.
Figure 1.1 – Recommended Usage Figure 1.2 – Not Recommended
*Note: See ‘Drive Letter Conflict’ on page 22.
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 3 of 22

Setup (Windows Environment)
1. Insert the DTL+ into an available USB port on
your notebook or desktop and wait for Windows
to detect it.
•Windows XP users will receive a ‘Found New
Hardware’ notification as seen in Figure 2.1.
•Windows Vista/7 users will receive a device
driver notification as seen in Figure 2.2.
Once the new hardware detection is complete,
Windows will prompt you to begin the initialization
process.
•Windows XP users can skip step 2 and go to
page 5 – Device Initialization.
•Windows Vista/7 users will see an AutoPlay
window similar to the one in Figure 2.3.
2. Select the option ‘Run DTLplus_Launcher.exe’.
If Windows does not AutoPlay, you can browse to
the CD-ROM partition (Figure 2.4) and manually
execute the DTLplus_Launcher program. This will
also start the initialization process.
Figure 2.4 – DTL+ Contents
Figure 2.1 – Found New Hardware
(Windows XP)
Figure 2.2 – Device Driver Installation
(Windows Vista/7)
Figure 2.3 – AutoPlay Window
(Windows Vista/7)
(Note: Menu options in the AutoPlay
window may vary depending on what
programs are currently installed on
your computer.AutoRun will start the
initialization process automatically.)
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 4 of 22

Device Initialization (Windows Environment)
1. Select your language preference from the drop-down menu and click ‘Next’ (Figure 3.1.)
Figure 3.1 – Language Selection
2. Review the license agreement and click ‘Next’ (Figure 3.2.) (Note: You must accept the
license agreement before continuing; otherwise the ‘Next’ button will remain disabled.)
Figure 3.2 – License Agreement
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 5 of 22

3. Create a password to protect your data on the DTL+. Enter it in the ‘Password’ field, then
re-enter it in the ‘Password Confirmation’ field, as seen below in Figure 3.3. The password
you create must meet the following criteria before the initialization process will allow you to
continue:
1. Passwords must contain 6 characters or more (up to 16 characters.)
2. Passwords must contain three (3) of the following criteria options:
- UPPER CASE, lower case, numeric, and/or special characters (!, $, etc.)
You may also enter a password hint, but it is not a mandatory field. The hint field can be
useful in providing a clue as to what the password is, should the password ever be
forgotten. (Note: The hint CANNOT be an exact match to the password.)
Figure 3.3 – Password Setup
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 6 of 22

4. Enter your contact information into the text boxes provided (see Figure 3.4) (Note: The
information you enter in these fields may NOT contain the password string you created in
Step 3. However, these fields are optional and can be left blank, if so desired.)
•The ‘Name’ field may contain up to 32 characters, but cannot contain the
exact password.
•The ‘Company’ field may contain up to 32 characters, but cannot contain
the exact password.
•The ‘Details’ field may contain up to 156 characters, but cannot contain
the exact password.
Figure 3.4 – Contact Information
5. Click ‘Finish’ to complete the device initialization process.
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 7 of 22

The DTL+ will now format the secure data partition (Figure 3.5) and notify you when it is
complete (Figure 3.6.)
Note: If operating under Windows XP in Non-Admin mode, the ‘Format’ routine
can take up to a minute.*
6. Click ‘OK’ to continue.
Figure 3.5 – Formatting DTL+ Figure 3.6 – Format Complete
Initialization complete.
*Note: Times may vary based on system hardware and the capacity of the DTL+ drive.
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 8 of 22

Device Usage (Windows Environment)
Once the DTL+ has been initialized, you can
access the secure data partition and utilize the
device options by logging into the device with
your password. To do so, follow these steps:
1. Insert the DTL+ into a USB port on your
notebook or desktop and enter your pass-
word (see Figure 4.1.)
2. Once you’ve typed your password, click the
‘Login’ button to continue.
•If the correct password is entered, the
DTL+ will unlock and you can begin
using the device.
•If an incorrect password is entered, an
error message will appear just below
the ‘Hint’ field, indicating a login
failure (see Figure 4.2.)
Figure 4.1 – Login Window
During the login process, if a bad password
is entered, you will be given another
opportunity to enter the correct password;
however, there is a built-in security feature
that tracks the number of failed login
attempts*. If this number reaches the pre-
configured value of 10 failed attempts, the
DTL+ will lock and require a device format
of the secure data partition prior to next
use.
THIS MEANS THAT ALL DATA STORED
ON THE DTL+ WILL BE LOST.
For more details on this feature, see
‘Device Lockout’ on page 20.
Figure 4.2 – Login Failure
*Note: Once you authenticate to the device successfully, the failed login counter will reset.
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 9 of 22

Device Options (Windows Environment)
While you are logged into the device, there will be a ‘DTL+’ icon located in the right-hand
corner of the Windows taskbar (Figure 5.1.) (Note: Windows 7 users will need to click on the
up-arrow button in the taskbar in order to access the ‘DTL+’ icon (Figure 5.2.)
Clicking once on the DTL+ icon will display the following menu:
Figure 5.1 – DTL+ icon in taskbar
Figure 5.2 – DTL+ icon in taskbar
(Windows 7 users)
DTL+ Settings
•Allows you to change your password and/or hint (Figure 5.3)
•Allows you to add/view/change your contact information (Figure 5.4)
•Allows you to change your current language selection (Figure 5.5)
(Note: For security purposes, your current DTL+ password is required to update and/or modify
any of these settings.)
Figure 5.3
Change Password
Figure 5.4
Contact Information
Figure 5.5
Select Language
Document No. 48008071-001.A02 DataTraveler®Locker+ Page 10 of 22