Kingtex MT4500 Series User manual

MT4500 MODEL NUMBERING SYSTEM ---------------------------------------------------------------------
1
1. MODELS ----------------------------------------------------------------------------------------------
-----------------
2
2. MOVING ------------------------------------------------------------------------------
---------------------------
2
3. HOW TO INSTALL THE MACHINE ----------------------------------------------
---------------------------
3
3
4
4. BEFORE OPERATION -------------------------------------------------------------------
---------------------------
5
5. NEEDLES ------------------------------------------------------------------------------
---------------------------
5
6.
CAUTION IN SETTING UP MOTOR BELT ---------------------------------------------------------------------
6
7. LUBRICATION --------------------------------------------------------------------------
---------------------------
7
8.
ASSEMBLING THE TENSION STAND OF MT4500/MTS4500---------------------------------------------------------------------
8
9.
ASSEMBLING THE TENSION STAND OF MT4000---------------------------------------------------------------------
9
10. THREADING THE MACHINE ------------------------------------------------------------------
---------------------------
10
11.
THREADING DIAGRAM FOR MT/MTS 4501 ---------------------------------------------------------------------
11
12.
THREADING DIAGRAM FOR MTT/MTS 4504 ---------------------------------------------------------------------
12
13.
THREADING DIAGRAM FOR MTT/MTS 4506 ---------------------------------------------------------------------
13
14.
THREADING DIAGRAM FOR MTT/MTS 4509 ---------------------------------------------------------------------
14
15.
THREADING DIAGRAM FOR MTT/MTS 4512 ---------------------------------------------------------------------
15
16.
THREADING DIAGRAM FOR MT4001 ---------------------------------------------------------------------
16
17.
THREADING DIAGRAM FOR MT4004 ---------------------------------------------------------------------
17
18.
THREADING DIAGRAM FOR MT4006 ---------------------------------------------------------------------
18
19.
THREADING DIAGRAM FOR MT4009 ---------------------------------------------------------------------
19
20.
THREADING DIAGRAM FOR MT4012 ---------------------------------------------------------------------
20
21.
ADJUSTING THE STITTCH FORMATION ---------------------------------------------------------------------
21
21-1 Thread tension adjustment --------------------------------
----------------------------------------------------------------
21
21
21
22.
TIMING OF THE LOOPER TO THE NEEDLE ---------------------------------------------------------------------
22
22
22
23. TIMING OF THE RETAINER LOOPER ---------------------------------------------------
---------------------------
23
23
23
24. ADJUSTING THE NEEDLE GUARD --------------------------------------------------------------
------------
23
25.
ADJUSTING THE FEED DOG & STITCH LENGTH ---------------------------------------------------------------------
24
25-1 Feed dog height & tilt -----------------------------------------------------------------------
--------------------------------
24
25-2 Stitch length ----------------------------------------
-----------------------------------------------------------------------
24
26. ADJUSTING THE PRESSER FOOT -----------------------------------------
--------------------------------------------------------------
25
26-1 Presser foot pressure -----------------------------------------
--------------------------------------------------------------
25
26-2 Position of the presser foot and foot lift --------------------------------------
-----------------------------------------------------------------
25
27.
ADJUSTING THE REAR PULLER DEVICE ---------------------------------------------------------------------
26
27-1 Manual lever and position of the stopper ------------------------
--------------------------------------------------------
26
27-2 To adjust the puller pressure --------------------------------------
-----------------------------------------------------------------
26
28. CLEANING THE MACHINE --------------------------------------
-----------------------------------------------------------------
27
29. MT SERIES TABLE CUT-OUT -------------------------------------------------------------
------------------------------------------
28
29-1 Short Table Top Type ------------------------------------------------------------------------------
---------------------
28
28
29-3 Long Table Top Type ------------------------------------------------------------------------
---------------------
29
29
30
30. MT SERIES TABLE CUT-OUT -------------------------------------------------------------
------------------------------------------
31
30-1 Short Table Top Type ------------------------------------------------------------------------------
---------------------
31
IMPORTANT SAFETY INSTRUCTION ---------------------------------------------------------------------
32
MT4500 SERIES CONTENTS
21-2 Position of the needle thread eyelet -----------------------------------------------
-------------------------------------------------
21-3 Adjusting the needle thread guard -----------------------------------------
-------------------------------------------------------
3-1 How to install MT series ------------------------------------------------------------------
---------------------------
3-2 How to install the tension stand of MT4509~MT4525 --------------------------------
---------------------------
29-2 Semi-Submerged Type ----------------------------------------------------------------------------------
--------
22-1 Positioning the looper and the looper rocker ---------------------------------------------------------------------
22-2 Looper left-to-right movement -----------------------------------------------------------
---------------------------
23-1 Installing the retainer looper ------------------------------------------------------------------
---------------------------
23-2 Timing of the retainer looper to the needle ---------------------------------------------------------------------
29-5 Applicable Models: MT4500 Class With "MP001+TC" Devic
--------------------------------------------
29-4 Applicable Models: MT4500 Class With "PS001" Devic
--------------------------------------------

1CM~2CM
pressed inward about 2 cm.
A.BELT: M type V belt and be sure that the motor turning
direction is clockwise and the motor belt tension can be
6.CAUTION IN SETTING UP MOTOR BELT
402 0001
Model
MT/MTS 4504P
MT/MTS 4512P
Maximum speed
4500
4000
Standard speed
4000
3500
< Machine speed >
< Motor pulley selection table >
50Hz
(mm)
60
70
3150
2300
2950
3450
60Hz
3300
3700
80
90
3900
4400
4100
110
100
4500 (5400)
(4900)
out diameter
Motor pulley Machine speed (SPM)
！
MT 4004P
MT4012P
When the needle bar is at the top of its stroke ,
5.1 Needle height
remove plug A on the head plate, loosen needle bar clamp B
with a hex. wrench and then move the needle bar up or down.
the center of the needle drop hole and then retighten the screw.
Note:
Standard needle height ( distance D )
Standard model
15 mm
With thread trimmer
14.5 mm
If this screw is looesend, make sure edch needle drops into
Do not loosen the screw on needle bar guide C.