Kingwo MT13 User manual

Vehicle GPS Tracker (MT13)
User Manual
(V1.1)
GPS Talks

MT13
Warm Notice
The contents of this manual might be renewed from time to time
without prior notice; KINGWO will improve or update the products or
operation procedures described in the manual at any time. If there is a
discrepancy between the real product and the manual, the real product
shall prevail. KINGWO has the final interpretation rights for this manual.
GPS Talks

MT13
Contents
Chapter 1: Product Overview ..........................................................................................................1
Chapter 2: Technical Specification .................................................................................................. 2
2.1 Specification..................................................................................................... 2
Chapter 3: Functions...................................................................................................................3
【Position】Position function .........................................................................3
Real time position.................................................................................3
Timely monitor......................................................................................3
Blind Zone Compensation.....................................................................3
Cornering Compensation...................................................................... 3
LBS .....................................................................................................4
AGPS ..........................................................................................................4
Alarm function .................................................................................................4
Emergency alarm ..........................................................................................4
Speeding alarm..............................................................................................4
Main power off alarm ...................................................................................5
Displacement alarm ......................................................................................5
Low Voltage Alarm........................................................................................5
Vibration Alarm .............................................................................................5
【Intelligent function】........................................5
Intelligent Power Save...................................................................................5
Intelligent Self-Diagnosis ..............................................................................6
Remote Control............................................................................................. 6
Static Drift Suppression ................................................................................6
Mileage Statistics..........................................................................................6
Remote Configuration................................................................................... 7
Vehicle Battery Protection......................................................................7
Remote Upgrade(OTA)..................................................................................7
SMS operation...............................................................................................7
Optional function (Protocol is required for integration)
Chapter 4: Installation guide..................................................................................7
Installation Diagram....................................................................................8
Installation and debugging process ..........................................................11
SIM installation ...................................................................................11
Main unit power on.......................................................................11
Recommended Installation place .........................................................12
Parameter setting by SMS..................................................................................... 12
GPS Talks

MT13
1
Chapter 1: Product Overview
GPS Talks

MT13
2
Chapter 2: Technical Specification
2.1 Specification
Mechanical
Size
Weight
Interface
RS232 interface
Data transmission
Packet data GPRS and SMS
Positioning method
GPS
Storage
4MB FLASH, up to 20000 GPS data storage
Power
Working Voltage
Working Current
GPS
Channels: 50
Sensitivity: -147dBm
Position accuracy:5-10m
Accuracy: 5m CEP
Cold start: <27s
Hot start: <1s
Cellular
Frequency
Module: QUECTEL MC25
GSM/GPRS 850/900/1800/1900 MHz
Working voltage: 3.3 –4.5 V (recommend 4.0V )
Transmitted power:
2 W 850/900 MHz
1 W 1800/1900 MHz
Chipset
STM32F070CB
Battery
Built in 850mAH battery,3.6V Lithium polymer battery, 8
hours working
GPS Talks

MT13
3
Chapter 3: Functions
【 Position 】 Position function
Real time position
Including timely upload, blind zone compensation, speed mileage statistics, area
monitoring and other functions, the backend sends positioning commands, and the
terminal uploads data including longitude, latitude, speed, direction, and status
information.
Timely monitor
The vehicle GPS terminal can be set to upload the position and status information of
the vehicle to the backend at a certain time or a certain period or at a certain time
interval.
Blind Zone Compensation
When the terminal enters the GPRS blind zone, the track data will be saved at the
shortest 15S interval, and the blind zone data will be uploaded to the backend when
the GPRS is back online. The blind zone compensation data can be saved up to
20000.
Cornering Compensation
When the vehicle enters the curve lane, the terminal detects that the driving
direction has a certain angular deviation (default 20 degrees), and a timing feedback
message is added to ensure that the driving track is more accurate.
GPS Talks

MT13
4
LBS
The terminal uses GPS positioning by default. When the GPS enters the blind zone
and cannot be accurately located, the terminal automatically switches to the base
station location. The terminal acquires the base station information every 30S and
uploads the base station information, the server interprets the specific location.
AGPS
The terminal has the AGPS function. When the terminal is connected to the GPRS,
the AGPS function can be used to speed up the positioning speed of the GPS module
and improve the positioning accuracy.
Alarm function
If the SMS alarm function is enabled, the configured number will receive SMS alarms
as well.
Emergency alarm
Press the SOS button, the backend will receive the SOS alarm, to protect the vehicle
from robbery and handle emergency cases
Speeding alarm
When the vehicle speed is higher than the overspeed alarm value, the vehicle
terminal will notify the backend. Similarly, when the vehicle speed is lower than the
low speed alarm value, a low speed alarm will be reported to the backend. The alarm
value is configurable.
GPS Talks

MT13
5
Main power off alarm
If the main battery is damaged and can not supply power, the built in back up
battery could keep the terminal working, and send a main power failure alarm to the
backend
Displacement alarm
An alarm is generated when the device is set to a displacement of more than 100
meters (message mode prompt), and the alarm information is reported when the
displacement radius exceeds 100 meters when the device is turned off. (Note:
displacement range 100~2000m)
Low Voltage Alarm
When the battery voltage on the vehicle is too low (0-11V or 19-22V), the vehicle
terminal reports a low voltage alarm to the backend
Vibration Alarm
The device activates the vibration alarm function. After the device is turned off for
more than 10 minutes (the fortification range: 1~20 minutes), the device generates
vibration and the ACC is not connected within 3 minutes (delay range: 1~10
minutes), and the device will report the vibration alarm information.
【 Intelligent function 】
Intelligent Power Save
The terminal has a built-in high-sensitivity G-sensor accelerometer that monitors the
vehicle for motion in real time. When no motion is detected for a long time, the
terminal automatically enters the power saving state, turns off the GPS/BD module,
GPS Talks

MT13
6
and GSM enters the heartbeat return state(Range 0-999). In this state, the power
consumption of the device is extremely low, which can greatly reduce the battery
usage of the vehicle.
Intelligent Self-Diagnosis
The vehicle terminal can perform self-diagnosis. In the event of a fault, it will send a
fault notification to the center, such as GPS, GSM, etc., and can automatically take
relevant measures. The backend can also query the current model, version,
configuration, running status, and device functions of the terminal.
Remote Control
Remotely controlling the vehicle lock, unlocking, and disable the abnormal state of
the terminal through the backend, the vehicle terminal receives the command, and
then performs corresponding operations on the vehicle circuit or the oil circuit, and
returns a power-off/oil confirmation message to the center, and simultaneously
implements uploading the current Vehicle status. Once the vehicle receives the
power/fuel cut off command, the vehicle terminal will memorize the status until the
center issues a recovery command.
Static Drift Suppression
The terminal has a built-in high-sensitivity G-sensor accelerometer and a complete
positioning data-filtering algorithm that filters out most of the static drift data to
ensure the accuracy of GPS data.
Mileage Statistics
The vehicle mileage data is returned to the backend along with the vehicle
positioning data; the initial mileage can be set when the vehicle is installed.
GPS Talks

MT13
7
Remote Configuration
To remote set the terminal parameters including IP, center number and various of
monitoring parameters via the backend
Vehicle Battery Protection
The terminal has high and low voltage protection, main power reverse connection
protection, power saving status, etc., to ensure that the car battery will not be
affected or damaged by the terminal.
Remote Upgrade(OTA)
As long as GPRS is available, remote firmware upgrade can be done wirelessly
SMS operation
To use SMS to set the terminal or query the working status of the terminal for easier
maintenance
Device is allowed to connect different accessories including fuel sensor, cameras,
temperature sensor and LED display etc
Optional function (Protocol is required for
integration)
GPS Talks

MT13
8
Chapter 4: Installation guide
Installation Diagram
GPRS Red LED
Slow Blink：GPRS Connected
Fast Blink：GPRS Unconnected
Solid on：Module Error
Backup Battery Switch
GPS GreenLED
Solid on：GPS Position
Slow Blink: LBS Position
LED Off ：Unpositioned
GPS Talks

MT13
9
Power cable
Red: Power 9-36V
Black: GND
Orange：ACC
Yellow：Lock Output
SOS
232 serial port
Black: GND
Green: RXD
Blue: TXD
Orange: DC Output
Front Side
White：power 12V/24V
Pin No
Color
Pin Name
Description
1
Black
GND
(-)Ground
2
Green
RXD
Serial Data Interface Rx
3
Blue
TXD
Serial Data Interface Tx
4
Orange
VDD 4V8
VDD 4V8_C
5
Grey
GND
Ground
6
Grey
SOS
SOS
GPS Talks

MT13
10
5PINdetecting wire
Pink：IO input 2，voltage 0~36V
Green：IO input 1，voltage 0~36V
Purple：IO output，0V or NC
Brown：AD input 2，voltage 0~5V
Blue：AD input 1，voltage 0~5V
7
Yellow
Fuel
CUT Fuel
8
Orange
ACC
ACCIN
9
Black
GND
(-)Ground
10
Red
VCC+
Power 9-36V
Back Side
MIC
Speaker
Pin No
Color
Pin Name
Description
1
Pink
DIN2
Digital Input2，Voltage range 0-36V
2
Green
DIN1
Digital Input1，Voltage range 0-36V
3
Purple
DOUT1
Digital output1
4
Brown
AD2
AD Input2voltage range 0-5V
5
Blue
AD1
AD Input1 voltage range 0-5V
GPS Talks

MT13
11
6
Brown
MIC+
MIC+
7
Brown
MIC-
MIC-
8
Black
GND
(-)Ground
9
Orange
SPK+
SPK+
10
Grey
SPK-
SPK-
Installation and debugging process
SIM installation
Open the top cover of the device, insert the prepared SIM card into the SIM
cardholder, and then confirm that the SIM card button is in place. Please make sure
that the SIM card has the GPRS function enabled in advance and record the SIM card
number in advance
Main unit power on
After installing the SIM card, turn the battery switch to the ON position. Meanwhile,
the red light starts to blink, indicating that the device is power on.
GPS Talks

MT13
12
Recommended Installation place
Parameter setting by SMS
Note: The device is with unique ID number, the factory can preset t IP, port and APN for
customers, generally there is no need for customers to do parameter setting; However in case
any configuration needs to be done, please follow below instructions and make sure the SIMs
has SMS functions available:
GPS Talks

MT13
13
APN,apn,user,pswd#
Set APN, User name and password
For example：APN,CMNET,internet,internet#
APN:CMNET
Username: internet
Password: internet
IP,ip or dns,port,type#
IP,119.23.233.52,6000,1#
Set the primary server IP:119.23.233.52 ， port 6000 ， communication type:TCP
IP,www.365qczx.com,6000,0#
Set the primary server domain:www.365qczx.com ， Port 6000 ， communication type
UDP
HC,<T1>,<T2>,<T3>#
Set the upload interval in real time tracking mode:
T1: upload interval in ignition on status, range,5-30s ,default 90s
T2: Upload interval in ignition off status
,range 5-600 s, default 120 s
T3：Sleep return interval, range 10-1800 s, default 180
For example:
HC,30,90# Set the upload interval as 30s and 90s in ignition on
HC,30,90,300# Set the upload interval as 30s, 90 s in ignition off and 300s while
in sleep mode
UTC,TTTT#
Set time zone，unit minutes, default UTC+8:00
For example:
UTC,480# Time zone UTC+8:00
UTC,330# Time zone UTC+5:30
UTC,-480# Time zone UTC-8:00
UTC,-210# Time zone UTC-3:30
WY,<A>[,R,M]#
Set towing alarm:
A: On and off，1:On 0:Off
Default is off
R: Towing radius，Default 500 meters，Range：100-2000 meters
M: Alarm mode，Optional
M=0:GPRS,M=1:SMS+GPRS
Eg：WY,1,100,1# towing alarm on，radius 100 metersnotification
mode:GPRS+SMS
GPS Talks

MT13
14
LOCKACCOFF,A#
Set vehicle lock
A=0 Receive lock command, execute immediately
A=1 Receive lock command, if ACC is off, execute immediately, if ACC is on, store
this command until ACC off
A=2 Store the command, lock vehicle from ACC Off to On, if the communication
is well, lock vehicle, otherwise wait for next turn
For example：LOCKACCOFF,0# means execute the lock command immediately
after receiving it
*22*1#
Restore to factory setting
*22*2#
Lock vehicle
*22*3#
Unlock vehicle
*22*4#
Reboot device
MT13 usage requirements
The device is strictly forbidden to use according to the operating instructions ,disassemble,
collide, charge, soak, over 80 °C, human failure, force majeure damage, etc. may cause short
circuit, insufficient working time, battery deformation, liquid leakage, explosion, no warranty and
compensation will be provided by KINGWO.
Contact us at:
LIBI Technologies Pvt. Ltd
Address: M1 and M2 Himland House, Commercial Complex, Ranjeet
Nagar, behind Satyam INOX Cinema, Patel Nagar, New Delhi,
Delhi-110008
Tel：[phone]
Website：https://www.libitechnologies.com
Email：[email protected]
GPS Talks