KitchenAid KSM60SPX User manual

Stand Mixer - Bowl Lift
KSM60SPX
KSM70SKX
1Motor Head
2Attachment Hub
3Attachment Knob
4Hub Cover
5Beater Shaft
6Speed Control Lever
7Bowl-Lift Lever
8Beater Height Adjustment Screw
9Bowl Support
10 Locating Pins
11 Bowl*
12 Bowl Handle*
13 Double Flex Edge Beater**
14 Flat Beater
15 Spiral Dough Hook
16 Wire Whip**
17 11-Wire Stainless Steel Elliptical
Whip**
18 Pouring Shield**
19 Spring Latch and Bowl Pin
(Not Shown)
20 Pastry Beater**
21 Scraper** ***
*Bowl type may vary. Bowls are also available for purchase as separate accessories.
**Included with select models. Picture/Style may vary from product depending on model.
***Can also be used to scrape your Bowl.
0 .5 1 2 3 4 5 6 7 8 9 10
1
3
2
6
8
7
9
10
11 12
13 14 15 16 17
18
4
19
20
5
21
W11584097B.indb 1W11584097B.indb 1 3/9/2023 4:48:34 PM3/9/2023 4:48:34 PM

2
PRODUCT SAFETY
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed, including the following:
1. Read all instructions. Misuse of appliance may result in personal injury.
2. To protect against the risk of electrical shock do not put Stand Mixer in water or
other liquid.
3. This appliance is not intended for use by persons (including children) with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge unless they are closely supervised and instructed concerning the
use of the appliance by a person responsible for their safety.
4. Children should be supervised to ensure that they do not play with the
appliance.
5. Turn the appliance off (0), then unplug from the outlet when not in use, before
assembling or disassembling parts and before cleaning. To unplug, grasp the
plug and pull from the outlet. Never pull from the power cord.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent, or similarly qualied persons in order to avoid a hazard.
7. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas
and other utensils, away from beater during operation to reduce the risk of
injury to persons, or damage to the mixer.
8. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or has been damaged in any manner. Return appliance
to the nearest Authorised Service Centre for examination, repair, or adjustment.
9. The use of accessories/attachments not recommended or sold by KitchenAid
may cause re, electrical shock, or injury to persons.
10. Do not use the Stand Mixer outdoors.
11. Do not let the cord hang over the edge of table or counter.
12. Allow the appliance to cool completely before putting on or taking off parts, and
before cleaning the appliance.
W11584097B.indb 2W11584097B.indb 2 3/9/2023 4:48:34 PM3/9/2023 4:48:34 PM

ENGLISH
3
13. Remove the Flat Beater, Wire Whip, Pastry Beater, Double Flex Edge Beater or
Spiral Dough Hook from the Stand Mixer before washing.
14. To avoid product damage, do not use the Stand Mixer Bowl in areas of high
heat such as an oven, microwave, or on a stovetop.
15. Refer to the “Care and Cleaning” section for instructions on cleaning the
surfaces in contact with food.
16. This appliance incorporates an earthed connection for functional purposes
only.
17. Do not use the Stand Mixer for anything other than its intended function as
specified in this manual.
18. This product is designed exclusively for domestic use.
19. This appliance is intended to be used in household and similar applications
such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
SAVE THESE INSTRUCTIONS
PRODUCT SAFETY
W11584097B.indb 3W11584097B.indb 3 3/9/2023 4:48:34 PM3/9/2023 4:48:34 PM

4
Electrical Shock Hazard
Plug into an earthed outlet.
Do not remove earth prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in
death, fire, or electrical shock.
ELECTRICAL REQUIREMENTS
Voltage: 220-240 V
Frequency: 50-60 Hz
NOTE: The Power rating for your Stand
Mixer is printed on the serial plate.
Do not use an extension cord. If the
power supply cord is too short, have a
qualified electrician or service person
install an outlet near the appliance.
The maximum rating is based on the
attachment that draws the greatest
load (Power). Other recommended
attachments may draw significantly less
Power.
ACCESSORY/SPEED CONTROL GUIDE
ACCESSORY USE FOR DESCRIPTION SPEED
Flat Beater
Mixing and
folding
ingredients
Folding delicate ingredients,
egg whites, cream, etc.
Mixing cakes, frostings,
cookies, etc.
0.5 speed for
folding
Speeds 1-6 for
mixing
Double Flex Edge
Beater*
Mixing and
creaming
ingredients
Creaming butter and sugar,
mixing cakes, frostings,
cookies, etc. Speeds 1-6
Spiral Dough Hook Kneading Breads, rolls, pizza dough,
etc. Speed 2
Wire Whip*/
11-Wire Elliptical
Whip* Whipping Eggs, Egg whites, cream, etc. Speeds 4-10
Pastry Beater*
Cutting
butter
into flour,
mashing
fruits/
vegetables,
shredding
meats
Pie dough and other pastries;
mashed potatoes/fruits/
vegetables, shredded chicken
Pastries (Cutting
butter into flour):
Speed 1-3,
Mashing fruits/
Vegetables: Up to
Speed 2
Mashing
potatoes,
Shredding Meat:
Speed 2
NOTE: Use Speed 2 to mix or knead yeast doughs. Use of higher speed creates high
potential for Stand Mixer failure. The PowerKnead Spiral Dough Hook efficiently kneads
most yeast dough within 4 minutes. The use of a lower speed might slow down the unit
and not thoroughly knead the dough.
*Available as an accessory purchase with selected models only.
PRODUCT SAFETY
W11584097B.indb 4W11584097B.indb 4 3/9/2023 4:48:34 PM3/9/2023 4:48:34 PM

ENGLISH
5
PRODUCT ASSEMBLY
IMPORTANT: If the Bowl is not securely snapped into place, it will be unstable and
wobble during use.
To attach the Accessory: Slip the
accessory onto the shaft. Turn to hook it
over the Pin on the shaft.
3
Pin
To Remove the Accessory: Turn the Stand
Mixer off (0) then unplug. Press accessory
upward and turn to the left. Pull down the
accessory from Beater Shaft.
4
Turn the Stand Mixer off (0) and then
Unplug.
To attach the Bowl: Fit the Bowl
Supports over Locating Pins and press
down on back of the Bowl until Bowl Pin
snaps into Spring Latch.
1
Spring Latch
Locating Pin
0 .5 1 2 3 4 5 6 7 8 9 10
To Remove Bowl: Place Bowl-Lift Lever in
the down position. Grasp Bowl Handle*
and lift straight up and off Locating Pins.
2
To raise the Bowl: Rotate the
Bowl-Lift Lever to the straight up
position. The Bowl must always be in the
raised position when mixing.
5
Test the Beater to Bowl Clearance: Turn
Stand Mixer ON and test each speed,
making sure the beater does not touch
the Bowl during operation. If the Beater
is too far away from the bottom or is
hitting the Bowl, proceed to next step to
make adjustments.
6
*Available as an accessory purchase with selected models only.
W11584097B.indb 5W11584097B.indb 5 3/9/2023 4:48:35 PM3/9/2023 4:48:35 PM

6
(OPTIONAL) To adjust Beater to
Bowl Cearance: Lower the Bowl to the
down position. Turn the screw slightly
counterclockwise (left) to raise the beater,
or clockwise (right) to lower it. Adjust the
beater so that it just clears the surface of
the Bowl. Check again the clearance of
the beater to the Bowl.
7
Raise Bowl
Raise Bowl
Lower Bowl
Lower Bowl IMPORTANT: When properly adjusted,
the Flat Beater will not strike on the
bottom or sides of the Bowl. If the Flat
Beater or the Wire Whip* is so close that
it strikes the bottom of the Bowl, coating
may wear off the beater or wires on the
whip may wear.
*Available with select models only and available as an accessory purchase.
PRODUCT USAGE
1. Turn the Stand Mixer off (0) and then Unplug.
2. Attach Bowl and Flat Beater, Dough Hook, or Wire Whip* to the mixer. Attach Bowl
and raise into locked position.
3. Place the shield onto the Bowl so that the Motor Head covers the U-shaped gap in
the shield. This will position the pouring chute just to the right of the Attachment Hub
as you face the Mixer. Press lightly so that the tabs snap the shield onto the Bowl.
4. Pour ingredients into the Bowl through the Pouring Chute.
USING THE POURING SHIELD*
DISASSEMBLING THE PRODUCT
1. Turn the Stand Mixer off (0) and then Unplug.
2. Lift the front of the Pouring Shield* clear of the rim of the Bowl. Pull away from the
Stand Mixer. Lower the Bowl and scrape.
PRODUCT ASSEMBLY
W11584097B.indb 6W11584097B.indb 6 3/9/2023 4:48:35 PM3/9/2023 4:48:35 PM

ENGLISH
7
PRODUCT USAGE
WARNING
Injury Hazard
Unplug mixer before touching
beaters.
Failure to do so can result in
broken bones, cuts, or bruises.
Electrical Shock Hazard
Plug into an earthed outlet.
Do not remove earth prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in
death, fire, or electrical shock.
1. Plug the Stand Mixer into a proper
electrical outlet. Start with lower speed
to avoid splashing and increase it
gradually. Refer to the “Speed Control
Guide”.
2. Do not scrape the Bowl while operating.
Scraping the Bowl once or twice during
mixing is usually sufficient.
OPTIONAL ATTACHMENTS
KitchenAid offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters,
or Food Grinder that may be attached to the Stand Mixer Attachment Hub.
Turn the Stand Mixer off (0) and then
unplug. Unscrew attachment Hub Cover.
Insert attachment into Attachment Hub,
making certain that attachment power
shaft fits into the square Attachment Hub
socket.
1
Tighten the Attachment Knob by turning
it clockwise until the attachment is
secured to the Stand Mixer.
2
NOTE: See the “Use and Care Guide” of each specific attachment for more details.
W11584097B.indb 7W11584097B.indb 7 3/9/2023 4:48:35 PM3/9/2023 4:48:35 PM

8
IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids.
Allow the appliance to cool completely before putting on or taking off parts, and
before cleaning the appliance.
CARE AND CLEANING
2. Wipe the Stand Mixer Body with a soft, damp cloth.
3. The Bowl is full dishwasher-safe.
The following parts are dishwasher-safe, top rack only: Flat Beater, Double Flex Edge
Beater*, Spiral Dough Hook, 11 Wire Elliptical Whip*, Pastry Beater*, Scraper* ** and
Pouring Shield*.
4. The following part should be hand-washed only, using warm, soapy water and drying
thoroughly: Wire Whip* only.
*Available with select models only and available as an accessory purchase.
**Can also be used to scrape your Bowl.
1
0 .5 1 2 3 4 5 6 7 8 9 10
Turn the Speed Control Lever to off (0)
and then Unplug.
W11584097B.indb 8W11584097B.indb 8 3/9/2023 4:48:36 PM3/9/2023 4:48:36 PM

ENGLISH
9
TROUBLESHOOTING GUIDE
Problem Solution
If Stand Mixer warms up during
use
Under heavy loads with extended mixing time periods, you
may not be able to comfortably touch the top of the Stand
Mixer. This is normal.
If Stand Mixer emits a pungent
odor during initial use This is normal. This is common with electric motors.
If the Flat Beater hits the Bowl Stop the Stand Mixer. See the “Product Assembly” section
and adjust the Beater to Bowl Clearance.
The Speed Control Lever does
not move smoothly or easily To move the Speed Control Lever with ease, lift slightly up as you move it across the settings in either direction.
If your Stand Mixer should fail
to operate, please check the
following
Is the Stand Mixer plugged in?
Is the fuse in the circuit to the Stand Mixer in working
order? If you have a circuit breaker box, be sure the circuit
is closed.
Turn off the Stand Mixer for 10-15 seconds, then turn it
back on. If the Stand Mixer still does not start, allow it to
cool for 30 minutes before turning it back on.
If product shuts off after
extensive use
Motor has automatic sensor that will keep motor from
overheating by shutting it off. If this occurs, turn the Speed
Control Lever to off (0) and let Stand Mixer rest for
30 minutes before restarting.
If mixer is slowing down or
appearing to struggle
Are you using the appropriate beater and speed? See
“Accessory/Speed Control Guide“ for more information.
Using 0.5 Speed or Speed 1 for bread doughs and heavy
loads might slow down the unit. Breads should knead with
the dough hook at Speed 2. If you have slowdown with
heavy loads at 0.5 Speed, increase to Speed 1 or 2.
If the problem cannot be
corrected
See the “Warranty and Service” section.
Do not return the Stand Mixer to the retailer; retailers do
not provide service.
WARNING
Electrical Shock Hazard
Plug into an earthed outlet.
Do not remove an earth prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire,
or electrical shock.
For customers in the US, please visit kitchenaid.com/pinch-of-help for additional product help.
©2023 All rights reserved. KITCHENAID and the design of the stand mixer are trademarks in the U.S.
and elsewhere. Used under license in Canada.
W11584097B.indb 9W11584097B.indb 9 3/9/2023 4:48:36 PM3/9/2023 4:48:36 PM

Batidora con base - Tazón levantable
KSM60SPX
KSM70SKX
1Cabeza del motor
2Receptáculo para aditamentos
3Perilla para aditamentos
4Tapa de receptáculo
5Eje del batidor
6Palanca de control de velocidad
7Palanca para levantar el tazón
8 Tornillo para regular la altura del batidor
9Soporte del tazón
10 Clavijas de ubicación
11 Tazón*
12 Manija del tazón*
13 Batidor doble de borde flexible**
14 Batidor plano
15 Gancho para masa en espiral
16 Batidor de alambre**
17 Batidor elíptico de acero inoxidable
de 11 alambres**
18 Escudo vertedor**
19 Seguro con resorte y clavija del tazón
(no se muestran)
20 Batidor para hojaldre**
21 Raspador** ***
*El tipo de tazón puede variar. Los tazones también se encuentran disponibles para la
compra como accesorios separados.
**Incluido con modelos específicos. La imagen/el estilo puede diferir del producto según
el modelo.
***Puede usarse también para raspar su tazón.
0 .5 1 2 3 4 5 6 7 8 9 10
1
3
2
6
8
7
9
10
11 12
13 14 15 16 17
18
4
19
20
5
21
W11584097B.indb 10W11584097B.indb 10 3/9/2023 4:48:36 PM3/9/2023 4:48:36 PM