KitchenAid KDRS505XSS00 User manual

INSTALLATION INSTRUCTIONS
30" (76.2 CM) DOUBLE OVEN DUAL FUEL RANGES
INSTRUCTIONS POUR L’INSTALLATION DES CUISINIERES
A BI-COMBUSTIBLE ET FOUR DOUBLE DE 30" (76,2 CM)
Table of Contents
RANGE SAFETY 2
INSTALLATION REQUIREMENTS.........c:ccscsseessssesseeessereeeenseeee 4
Tools and Parts. A
Location Requirement ......ccccccceececccseeeteeveneveeeeeeeeenereneenereneeennennes 4
Electrical Requirements - U.S.A. Only ........ cece eee ree reeeeeeeeeeee 6
Electrical Requirements - Canada Only .......... eee eerste 7
Gas Supply Requirement ......... cece eee cee eeeeteeeeeeeenerenerenevenees 7
INSTALLATION INSTRUCTIONS. ......cccsccsseessesseseeseeenseneeseeensennanee 9
Unpack Range ....cccceecccceececeteeceereeeeecenesenereeveneesenereneeneveneeenenees 9
Adjust Leveling Legs ... wid
Install Anti-Tip Bracket... 10
Electrical Connection - U.S.A. Only tt
Make Gas Connection... ec ce cece secre renscerereeseereeneees 16
Verify Anti-Tip Bracket Location 0.0.2... eeee eee teseeereeeeeeeeenereneeee 17
Level RAnge ......cccccccccsccecececeeeeeeeneceeseneveneeeaueneessneveneesarenerenevenees 17
Electronic Ignition SYStem occ eee eee teeeenereeeseneteereneeeeeeaees 18
Complete Installation... cece cee ceeeeeeeee sens tee reneveneereneeneraee 18
GAS CONVERSIONS. 19
LP Gas ConverSion.... eee ee ce eeeee reese ssscsereesceerevesseereeeneees 19
Natural Gas Conversion .. 20
Moving the Range .......ccccccccccecccecee cee cene cece eeeenee cee ences cereneeseeneees 22
zs
Table des matieres
ECURITE DE LA CUISINIERE 24
EXIGENCES D’INSTALLATION 26
Outils et COMPOSANS ....cccccecccece cece cceeee cece cece cee ceeeeeeeeceeeseeceeeeeeeeeeeeeees 26
Exigences d'emplacement ...........eceeee ce ceeereeereeeeeeesenereneveneeneeseneraee 26
SpEcifications Slectriques .......ccccccccceeeceeceeseeseeseeeveneeeeneseeveneveeveneeeaees 28
Spécifications de l’alimentation ON GAZ .....ccccccccccccececceceeeceeeeeeeteeneees 29
INSTRUCTIONS D'INSTALLATION ........:sscssscsseesssesseessesseeseesseeensees 31
Déballage de la CUISINIGrE «oo... cece eee eee eee tee tee teee eens reneenereneeneeeneraee 31
Réglage des pieds de nivellement........cc..c:ceeeeeeee eens rene reeeeeeeenereee 31
Installation de la bride antibasculement. 382
Raccordement QU QaZ.....ccccecccccceete eee teeeeeeecceeceeeteneneeenecneeeae 33
V6rification de l'emplacement de la bride antibasculement
Réglage de l'aplomb de la CUISINIGre..... ee ee eee cette reer eeeee teers
Systeme d'allumage Electronique 2.0... ee cece teeeeeeeeeee tens tee teeeeeeees
Achever l'installation 00... eee reece see eeeeeeeeeeeeeeeeeneees
CONVERSIONS DE GAZ
Conversion pour l'alimentation au gaz propane
Conversion pour l'alimentation au gaz naturel.
Déplacement de la CUISINIGFE...... eee eee cette teeee eens renters reneeneeeenereee
IMPORTANT:
Save for local electrical inspector's use.
IMPORTANT :
A conserver pour consultation par l'inspecteur local des installations électriques.
W10291448A

RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER?” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
A DANG ER follow instructions.
You can be killed or seriously injured if you don't follow
AWARNING instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
e Do not try to light any appliance.
e Do not touch any electrical switch.
e Do not use any phone in your building.
e Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
e If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.

In the State of Massachusetts, the following installation instructions apply:
@ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
@ If using a ball valve, it shall be a T-handle type.
@ A flexible gas connector, when used, must not exceed 3 feet.
AWARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATION REQUIREMENTS
Tools and Paris
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure ¥e" nut driver
Phillips screwdriver Marker or pencil
T20 Torx’ screwdriver m Pipe-joint compound
Flat-blade screwdriver resistant to LP gas
%" flat-blade screwdriver Noncorrosive leak-detection
Level For LP/Natural Gas
Conversions
¥2" combination wrench
Hand or electric drill
Wrench or pliers a
Pipe wrench mg %2" (7.0 mm) nut driver
1546" combination wrench ™ Masking tape
Ya" (3.2 mm) drill bit
Parts supplied
Check that all parts are included.
m 3- 10-32 hex nuts (attached to terminal block)
mg 3 - Terminal lugs
mg LP/Natural Gas Conversion Kit (located on back of range near
lower side)
Burner grates
Burner caps
Oven racks
2 - #12 x 1%" screws (for mounting anti-tip bracket)
Anti-tip bracket (taped inside upper oven with literature
package)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts needed
If using a power supply cord:
m AUL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 volts minimum, 40 amps or
50 amps that is marked for use with nominal 196" (8.5 cm)
diameter connection opening and must end in ring terminals
or open-end spade terminals with upturned ends.
m A UL listed strain relief.
Check local codes and consult gas supplier. Check existing
electrical supply and gas supply. See “Electrical Requirements”
and “Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
T®TORX is a registered trademark of Acument Intellectual Properties, LLC
4
ocalion Requirement!
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
g_ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located behind the control panel
and may be rotated up from behind the control panel for
viewing from the front of the range.
The range should be located for convenient use in the kitchen.
Recessed installations must provide complete enclosure of
the sides and rear of the range.
mg Toeliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood or
microwave hood combination that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
a All openings in the wall or floor where range is to be installed
must be sealed.
Do not seal the range to the side cabinets.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
gm The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see “Install Anti-Tip
Bracket” section.
m Grounded electrical supply is required. See “Electrical
Requirements” section.
m Proper gas supply connection must be available. See “Gas
Supply Requirements” section.
m Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
m Use an insulated pad or 44" (0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANS] A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-latest edition, or with local
codes.
Mobile home installations require:
m When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing the
range is adequate as long as it conforms to the standards
listed above.
m Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See “Electrical Connection” section.

Product Dimensions
A. 3594" + 38" (90.8 + 0.3 cm)
cooktop height (minimum)
with leveling legs screwed all
the way in
B. Model/serial/rating plates
(located behind the control
panel)*
C. 47%" + Ye" (119.7 + 0.3. cm)
overall height (minimum) with
leveling legs screwed all the
way in**
D, 2848" + 14" (72.4 + 0.6 cm)
depth with handle
E, 2646" + 1" (66.4 + 0.3 cm)
F. 29146" + Vie" (76.0 + 0.2 cm)
width
*Model/serial/rating plates may be rotated up from behind the
control panel for viewing from the front of the range.
™ Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
““Excludes handle. Dimension given is from wall to front of oven
door and will vary based on electric outlet receptacle
installation.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
i
_
‘Ler
Sg
|
4a
(35.6
cm)
8Y2" (21.6 cm)*
gas line location
A. 18" (45.7 cm) upper cabinet to countertop
B. 13" (33.0 cm) upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to the top of the cooktop, see NOTE.
E. 30" (76.2 cm) min. opening width
F, 3" (7.6 cm) min. clearance from both sides of the range to the side
wail or other combustible material.
G. Cabinet door or hinges should not extend into the cutout.
H. 3" (7.6 cm) distance from wall
1.1%" (3.8 cm) min. from right side cabinet
J. 8" (20.3 cm) width
K.7" (17.8 cm) min. from floor
L. 2" (5.1 cm) min. from floor
*Drill on centerline 1%" (3.1 cm) from rear wall for gas supply
line.
**Gas lines must be installed within the shaded area to ensure
proper alignment of this oven with cabinets.
“Recessed electrical plugs must be installed within the shaded
area to ensure proper alignment of this oven with cabinets.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than 14" (0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30” (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.

Electrical Requirerr
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70-latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269.
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician if you are in doubt as to whether the appliance
is properly grounded. Do not modify the power supply cord plug.
If it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
m Range must be connected to the proper electrical voltage and
frequency as specified on the model/serial number rating
plate. The model/serial number rating plate is located behind
the control panel. Refer to the figures in “Product Dimensions”
in the “Location Requirements” section.
mg This range is manufactured with the neutral terminal
connected to the cabinet. Use a 3-wire, UL listed, 40- or
50-amp power supply cord (pigtail) (see following Range
Rating chart). If local codes do not permit ground through the
neutral, use a 4-wire power supply cord rated at 250 volts,
A0 or 50 amps and investigated for use with ranges.
Range Rating* Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts 120/208 Volts Amps
8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50**
16.6 - 22.5 KW 12.6 - 18.5 KW 50
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
“If connecting to a 50-amp circuit, use a 50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1%" (34.9 mm) diameter connection opening.
a Acircuit breaker is recommended.
m Therange can be connected directly to the circuit breaker box
(or fused disconnect) through flexible or nonmetallic sheathed,
copper or aluminum cable. See the “Electrical Connection -
U.S.A. Only” section.
gm Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that
the range can be moved if servicing is ever necessary.
rents - U.S.A. Only
gm AULlisted conduit connector must be provided at each end
of the power supply cable (at the range and at the junction
box).
m Wire sizes and connections must conform with the rating of
the range.
m The wiring diagram is located on the back of the range or in a
clear plastic bag.
If connecting to a 4-wire system:
This range is manufactured with the ground connected to the
neutral by a link. The ground must be revised so the green ground
wire of the 4-wire power supply cord is connected to the cabinet.
See “Electrical Connection Section.”
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord (pigtail) must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50P plug on the
supply end.
The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.
O
UU
U
4-wire receptacle (14-50R)
The minimum conductor sized for the copper 4-wire power
cord are:
40-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-8 green grounding
If connecting to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.
3-wire receptacle (10-50R)

°
Electrical Shock Hazard
Electrically ground range.
Failure to do so can result in death, fire, or
electrical shock.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate and wire gauge are in accordance
with local codes.
Be sure that the electrical connection and wire size are adequate
and in conformance with CSA Standard C22.1, Canadian
Electrical Code, Part 1 - latest edition, and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
tn cory uote senig 0 ging Ltn be, g
- Canada Only
m= Check with a qualified electrical installer if you are not sure the
range is properly grounded.
Range Rating* Rating of Circuit
Power Protection
Supply
Cord
120/240 Volts 120/208 Volts Amps Amps
8.8-165KW 7.8-125KW 40 40 or 50
16.6 - 22.5 12.6 - 18.5 50 50
KW KW
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
A time-delay fuse or circuit breaker is recommended.
This range is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-50R
wall receptacle. Be sure the wall receptacle is within reach of
range’s final location.
O
UU
U
m Donot use an extension cord.
s Supply Re
AWARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI 2223.1 - latest edition or CAN/CGA B149 - latest
edition.
Yb
equiremenis
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer’s instructions.
Type of Gas
Natural gas:
This range is design-certified by CSA International for use with
Natural gas or, after proper conversion, for use with LP gas.
m_ This range is factory set for use with Natural gas. See “Gas
Conversions” section. The model/serial rating plate located
behind the control panel has information on the types of gas
that can be used. If the types of gas listed do not include the
type of gas available, check with the local gas supplier.
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See “Gas
Conversions” section.
Gas Supply Line
m Provide a gas supply line of 34" (1.9 cm) rigid pipe to the range
location. A smaller size pipe on longer runs may result in
insufficient gas supply. With LP gas, piping or tubing size can
be ¥2" (1.38 cm) minimum. Usually, LP gas suppliers determine
the size and materials used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON tape.
T®TEFLON is a registered trademark of E.1. Du Pont De Nemours and Company.
7

Flexible metal appliance connector:
m_ lf local codes permit, a new CSA design-certified,
4 to 5 ft (122 to 152.4 cm) long, ¥2" (1.3 cm) or
34" (1.9 cm) |.D., flexible metal appliance connector may
be used for connecting range to the gas supply line.
mg A‘%" (1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the appliance
pressure regulator.
m Do not kink or damage the flexible metal tubing when
moving the range.
Rigid pipe connection:
The rigid pipe connection requires a combination of pipe
fittings to obtain an in-line connection to the range. The rigid
pipe must be level with the range connection. All strains must
be removed from the supply and fuel lines so range will be
level and in line.
Must include a shutoff valve:
The supply line must be equipped with a manual shutoff valve.
This valve should be located in the same room but external to
the range opening, such as an adjacent cabinet. It should be
in a location that allows ease of opening and closing. Do not
block access to shutoff valve. The valve is for turning on or
shutting off gas to the range.
A. Gas supply line
B. Shutoff valve “open” position
C. To range
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be used.
The inlet pressure to the regulator should be as follows for proper
operation:
Natural gas:
Minimum pressure: 5" WCP
Maximum pressure: 14" WCP
LP gas:
Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at a
rate of 4% for each 1,000 ft (804.8 m) above sea level (not
applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least
1" water column pressure above the manifold pressure shown on
the model/serial rating plate.
Line pressure testing above 12 psi gauge (14" WCP)
The range and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 2 psi (8.5 kPa).
Line pressure testing at 2 psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than ¥ psi (3.5 kPa).

INSTALLATION INSTRUCTIONS
npack Range
AWARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
id
Remove shipping materials, tape and film from the range.
Keep cardboard bottom under range.
Remove oven racks and parts package from inside oven.
To place range on its back, take 4 cardboard corners from the
carton. Stack one cardboard corner on top of another. Repeat
with the other 2 corners. Place them lengthwise on the floor
behind the range to support the range when it is laid on its
back.
Using 2 or more people, firmly grasp the range and gently lay
it on its back on the cardboard corners.
Pull cardboard bottom firmly to remove.
Use an adjustable wrench to loosen the leveling legs.
Place cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto cardboard or
hardboard.
bs
ee
If range height adjustment is necessary, use a wrench or pliers
to loosen the 4 leveling legs.
This may be done with the range on its back or with the range
supported on 2 legs after the range has been placed back toa
standing position.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto the cardboard or
hardboard.
AWARNING
¥
y
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
2. Adjust the leveling legs to the correct height. Leveling legs can
be loosened to add up to a maximum of 1" (2.5 cm). A
minimum of %s" (5.0 mm) is needed to engage the anti-tip
bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, then tilt forward to
adjust the rear legs.
When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final location, check that the anti-
tip bracket will slide under the range and onto the rear leveling
leg prior to anti-tip bracket installation.

10
Foor Mounting
al
=
Remove the anti-tip bracket that is taped inside the upper
oven with the package containing literature.
Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor you can use the wall
mounting method.
Determine and mark edge of range in the cutout space. The
mounting bracket can be installed on either the left side or
right side of the cutout. Position mounting bracket in cutout so
that right (or left) edge of the bracket is “6” (2.4 cm) from the
marked edge of the range, as shown.
Wall Mounting
A. Anti-tip bracket
B. Mark edge of range.
C. 16" (2.4 cm)
Drill two ¥%" (3.0 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following.
A. #12 x 15%" screws
B. Anti-tip bracket
A. #12 x 1%" screws
B. Anti-tio bracket
5. Using the Phillips screwdriver, mount anti-tip bracket to the
wall or floor with the two #12 x 1%" screws provided.

Eg Pas ape, ile, gi "Oh sy 0 uy (ln, te, LAG Oe, i id Oy bey
Electrical Connection - U.S.A. Only
Power Supply Cord Direct Wire
AWARNING
a a
Electrical Shock Hazard Electrical Shock Hazard
Disconnect power before servicing. Disconnect power before servicing.
Use a new 40 amp power supply cord. Use 8 gauge copper or 6 gauge aluminum wire.
Plug into a grounded outlet. Electrically ground range.
Failure to follow these instructions can result in death, Failure to follow these instructions can result in death,
fire, or electrical shock. fire, or electrical shock.
1. Disconnect power. 4. Add strain relief.
2. Use Phillips screwdriver to remove the terminal block cover Style 1: Power supply cord strain relief
screw located on the back of the range. Pull cover down and
toward you to remove cover. m Assemble a UL listed strain relief in the opening.
3. Remove plastic tag holding three 10-32 hex nuts from the
middle post of the terminal block.
A. UL listed strain relief
m Feed the power supply cord through the strain relief in the
cord/conduit plate on bottom of range. Allow enough
slack to easily attach the wiring to the terminal block.
mg Tighten strain relief screw against the power supply cord.
11

12
Style 2: Direct wire strain relief
m Use Phillips screwdriver to remove screws and slide
cord/conduit plate down and out.
m Position cord/conduit plate as shown in the following
illustration.
7
3-wire (if 4-wire is not available)
Electrical Connection Options
mg Feed the flexible conduit through the strain relief, allowing
enough slack to easily attach wiring to the terminal block.
mg Tighten strain relief screw against the flexible conduit.
5. Replace back panel and screws on rear of range.
6. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
If your home has: And you will be
connecting to:
Go to Section:
4-wire receptacle
(NEMA type 14-50R)
oO
A UL listed,
250-volt
minimum,
40-amp, range
power supply
cord
4-wire connection:
Power supply cord
4-wire direct
(12.7 cm)
A fused
disconnect or
circuit breaker
box
4-wire connection:
Direct wire
3-wire receptacle
(NEMA type 10-50R)
A UL listed,
250-volt
minimum,
40-amp, range
power supply
cord
3-wire connection:
Power supply cord
3-wire direct
(2.5 om).
at
“G6 cm)
A fused
disconnect or
circuit breaker
box
3-wire connection:
Direct wire
A. Removable retaining nut
B. Strain relief

4-wire connection: Power Supply Cord
Use this method for:
New branch-circuit installations (1996 NEC)
Mobile homes
Recreational vehicles
In an area where local codes prohibit grounding through the
neutral
Part of metal ground strap must be cut out and removed.
A. Metal ground strap
B. Discard
C. Ground-link screw
Use Phillips screwdriver to remove the ground-link screw from
the back of the range. Save the ground-link screw and the end
of the ground link under the screw.
Feed the power supply cord through the strain relief in the
cord/conduit plate on bottom of range. Allow enough slack to
easily attach the wiring to the terminal block.
A. Terminal block
B. Ground-link screw
C. Cord/conduit plate
D. Power supply cord wires
Use Phillips screwdriver to connect the green ground wire
from the power supply cord to the range with the ground-link
screw. The ground wire must be attached first.
Use %" nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.
A. 10-32 hex nut
B. Ground-link screw
C. Line 7 (black)
D. Green ground wire
E, Neutral (center) wire
F. Line 2 (red)
Connect line 1 (black) and line 2 (red) wires to the outer
terminal block posts with 10-32 hex nuts.
Securely tighten hex nuts.
NOTE: For power supply cord replacement, use only a power
cord rated at 250 volts minimum, 40 amps or 50 amps that is
marked for use with nominal 19%" (3.5 cm) diameter
connection opening, with ring terminals and marked for use
with ranges.
Replace terminal block access cover.
13

3-wire connection: Power Supply Cord Direct Wire Installation: Copper or Aluminum Wire
Use this method only if local codes permit connecting chassis
ground conductor to neutral wire of power supply cord.
1. Feed the power supply cord through the strain relief in the
easily attach the wiring to the terminal block.
This range may be connected directly to the fuse disconnect or
circuit breaker box. Depending on your electrical supply, make the
required 3-wire or 4-wire connection.
cord/conduit plate on bottom of range. Allow enough slack to 1. Strip outer covering back 3” (7.6 cm) to expose wires. Strip
the insulation back 1” (2.5 cm) from the end of each wire.
i
25 om)
me
Allow enough slack in the wire to easily attach the wiring
terminal block.
Complete electrical connection according to your type of
electrical supply (4-wire or 3-wire connection).
4-wire Connection: Direct Wire
a
a
a
a
A. Terminal block
B. Ground-link screw 1.
C. Cord/conduit plate
D. Power supply cord wires
2. Use ¥%" nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.
wF
2.
A. 10-32 hex nut
B. Line 7 (black)
C. Ground-link screw
D. Neutral (white) wire
E. Line 2 (red)
3. Connect line 1 (black) and line 2 (red) wires to the outer
terminal block posts with 10-32 hex nuts.
4. Securely tighten hex nuts.
NOTE: For power supply cord replacement, use only a power
cord rated at 250 volts minimum, 40 amps or 50 amps that is
marked for use with nominal 18" (8.5 cm) diameter
connection opening, with ring terminals and marked for use
with ranges.
5. Replace terminal block access cover.
14
Use this method for:
New branch-circuit installations (1996 NEC)
Mobile homes
Recreational vehicles
In an area where local codes prohibit grounding through the
neutral
Part of metal ground strap must be cut out and removed.
A. Metal ground strap
B. Discard
C. Ground-link screw
Use Phillips screwdriver to remove the ground-link screw from
the back of the range. Save the ground-link screw and the end
of the ground link under the screw.

3. Pull the conduit through the strain relief on cord/conduit plate 5. Use Phillips screwdriver to connect the bare (green) ground
on bottom of range. Allow enough slack to easily attach wiring wire to the range with the ground-link screw. The ground wire
to the terminal block. must be attached first and must not contact any other
terminal.
6. Use %" nut driver to connect the neutral (white) lug to the
center terminal block post with one of the 10-32 hex nuts.
A
tue
ry
—_—
fa
an
- G
7:
on
“
a
[
OF
\
E
A.
10-32
hex
nut
E,
Neutral
(white)
wire
B.
Line
7
(black)
F,
Line
2
(red)
C.
Bare
(green)
ground
wire
G.
Terminal
lug
A.
Terminal
block
E,
Neutral
(white)
wire
D.
Ground-link
screw
B.
Ground-link
screw
F.
Line
7
(black)
wire
. . .
C.
Cord/conduit
plate
G.
Bare
(green)
ground
wire
7.
Connect
line
1
(black)
and
line
2
(red)
terminal
lugs
to
the
outer
terminal block posts with 10-32 hex nuts.
Securely tighten hex nuts.
4. Attach terminal lugs (located in the package containing i
literature) to line 1 (black), neutral (white), and line 2 (red) wires. 9. Replace terminal block access cover.
D. Line 2 (red) wire
9
Loosen (do not remove) the setscrew on the front of the
terminal lug and insert exposed wire end through bottom of 3-wire connection: Direct Wire
terminal lugs. Securely tighten setscrew to : : : :
XX Ibs-in. torque. See Bare Wire Torque Specifications chart. Use this method only if local codes permit connecting ground
conductor to neutral supply wire.
1. Pull the conduit through the hole and conduit plate on bottom
of range. Allow enough slack to easily attach the wiring to the
terminal block.
S
S
A. Terminal lug
B. Setscrew
C. Line 1 (black) wire
D. Neutral (white) wire
E. Line 2 (red) wire
Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)
Wire Awg Torque
8 gauge copper 25 Ibs-in. (2.8 N-m) A. Terminal block D. Line 2 (red) wire
- - B. Ground-link screw E. Bare (green) ground wire
6 gauge aluminum 35 Ibs-in. (4.0 N-m) C. Cord/conduit plate F, Line 1 (black) wire
15

2. Attach terminal lugs (located in the package containing
literature) to line 1 (black), bare (green) ground, and line 2 (red)
wires. Loosen (do not remove) the setscrew on the front of the
terminal lug and insert exposed wire end through bottom of
terminal lugs. Securely tighten setscrew to
XX Ibs-in. torque. See Bare Wire Torque Specifications chart.
A
9
o m
A. Terminal lug
B. Setscrew
C. Line 1 (black) wire
D. Bare (green) ground wire
E. Line 2 (red) wire
Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)
Wire Awg Torque
Make Gas Connection
AWARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
8 gauge copper 25 lbs-in. (2.8 N-m)
6 gauge aluminum 35 Ibs-in. (4.0 N-m)
3. Use %" nut driver to connect the bare (green) ground terminal
lug to the center terminal block post with one of the 10-32 hex
nuts.
A. 10-32 hex nut
B. Line 1 (black)
C. Ground-link screw
D. Bare (green) ground wire
E. Line 2 (red)
F. Terminal lug
4. Connect line 1 (black) and line 2 (red) terminal lugs to the outer
terminal block posts with 10-32 hex nuts.
5. Securely tighten hex nuts.
6. Replace terminal block access cover.
16
Typical flexible connection
1. Apply pipe-joint compound made for use with LP gas to the
smaller thread ends of the flexible connector adapters (see B
and G in the following illustration).
2. Attach one adapter to the gas pressure regulator and the other
adapter to the gas shutoff valve. Tighten both adapters.
3. Use ate" combination wrench and an adjustable wrench to
attach the flexible connector to the adapters. Check that
connector is not kinked.
E. Manual gas shutoff valve
F. ¥2" or %4" gas pipe
G. Use pipe-joint compound.
H. Adapter
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have 2" male
pipe thread)
D. Flexible connector

4. Gas supply pipe must be located within clearance area as
shown in the “Cabinet Dimensions” illustration in “Location
Requirements” section.
Complete connection
1. Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
A. Closed valve
B. Open valve
2. Test all connections by brushing on an approved noncorrosive
leak-detection solution. If bubbles appear, a leak is indicated.
Correct any leak found.
3. Remove cooktop burner caps and grates from parts package.
Align recess in burner caps with pins in burner base. Burner
caps should be level when properly positioned. If burner caps
are not properly positioned, surface burners will not light.
Place burner grates over burners and caps.
4. Plug in range or reconnect power.
4
» Bsr, elie, Be gabe CS gem, C8 gegnes souk p goad | sim, gre, poght sor,
Verify Anti-Tip Bracket Location
Move range close to cabinet opening.
Remove cardboard or hardboard from under the range. Using
2 or more people, gently move range into its final location.
3. To check that the anti-tip bracket is installed, use a flashlight
and look underneath the bottom of the range.
mg Look for the anti-tip bracket securely attached to floor or
wall.
Ny
=
m Slide range back so rear range foot is under anti-tip
bracket.
Level Range
Place oven rack in oven.
Place level on oven rack and check levelness of range, first
side to side; then front to back.
no
—
3. If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
4. Use wrench to adjust leveling legs up or down until range is
level. Push range back into position.
5. Check that rear leveling leg is engaged in anti-tip bracket.
Check that the flexible conduit or power supply cord are not
bent.
NOTE: Range must be level for satisfactory baking performance.
VES pi gia Aer give, gi, gia, |) poe op AE yong yu, Go, y edo, won
Electronic ignition Sysiem
Initial lighting and gas flame adjustments
Cooktop burners use pilotless igniters in place of standing pilots.
When the cooktop control knob is turned to the “LITE” position,
the system creates a spark to light the burner. This sparking
continues, as long as the control knob is turned to “LITE.”
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the “LITE” position.
The flame should light within 4 seconds. The first time a burner is
lit it may take longer than 4 seconds to light because of air in the
gas line.
If burners do not light properly:
m= Turn cooktop control knob to the “OFF” position.
m Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
Check that the gas shutoff valve is set to the “open” position.
m Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn the
control knobs to “Off” and contact your dealer or authorized
service company for assistance.
17

Tap Touch Surface Burners (on some models)
Tap the “On” pad for the cooktop control.
Tap the + or - to adjust the cooktop burner flame hieght. The
flame should light within 4 seconds. The first time a burner is lit it
may take longer than 4 seconds to light because of air in the gas
line.
If burners do not light properly:
mg Tap the “Off” pad for the cooktop control.
m Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
Check that the gas shutoff valve is set to the “open” position.
m Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, tap the
“Off” pad for the cooktop control and contact your dealer or
authorized service company for assistance.
Adjust Flame Height
Adjust the height of top burner flames. The cooktop “low” burner
flame should be a steady blue flame approximately %4" (0.64 cm)
high.
ee
A Og [el Cal Tal Tal Tal Cal
Z.
A. Low flame
B. High flame
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
18
If the “low” flame needs to be adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem in the low position using a pair of pliers. Use
an %" (3.0 mm) flat-blade screwdriver to turn the screw located in
the center of the control knob stem until the flame is the proper
size.
e Replace the control knob.
4. Test the flame by turning the control from “LO” to “HI,”
checking the flame at each setting.
5. Repeat above steps for each burner.
Complete Installation
Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
Check that you have all of your tools.
Dispose of/recycle all packaging materials.
Check that range level. See “Level Range.”
Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see the
“Range Care” section of the Use and Care Guide.
6. Read “Range Use” in the Use and Care Guide.
7. Turn on surface burners and oven. See the Use and Care
Guide for specific instruction on range operation.
If range does not operate, check the following:
m Household fuse is intact and tight, or circuit breaker has not
tripped.
—_
oP
ON
m Range is plugged into a properly grounded outlet.
Electrical supply is connected.
m See “Troubleshooting” in the Use and Care Guide.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the
Use and Care Guide or contact the dealer from whom you
purchased your range.

GAS CONVERSIONS
Gas conversions from Natural gas to LP gas or from LP gas to
Natural gas must be done by a qualified installer.
a te
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
LP Gas Conversion
AWARNING
v
a
©.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Turn manual shutoff valve to the closed position.
A. To range
B. Shutoff valve (closed position)
C. Gas supply line
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator
1. Locate gas pressure regulator at the rear of the range.
A. Gas pressure regulator
IMPORTANT: Do not remove the gas pressure regulator.
2. Unscrew the hex-shaped regulator cap from the regulator and
remove the regulator pin.
A. Regulator pin
B. Regulator cap
3. Flip the regulator pin over and snap pin firmly into place.
Ly
A. Natural gas position
B. LP gas position
4. Screw the hex-shaped regulator cap securely back into place.
Do not overtighten.
19

To Convert Surface Burners
1. Ifinstalled, remove the burner grates.
Remove the burner caps.
3. Using a Phillips or T20 Torx® screwdriver, remove the burner
base.
A. Burner cap
B. Gas tube opening
C. Burner base screws
D. Burner base
4. Apply masking tape to the end of a %2" (7.0 mm) nut driver to
help hold the Natural gas orifice spud in the nut driver while
changing it. Press nut driver down onto the Natural gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the Natural gas orifice spud aside.
A. Natural gas orifice spud
Use the following chart for correct LP gas orifice spud for each
burner. Refer to the model/serial rating plate behind the control
panel for proper sizing of LP gas orifice spuds for each burner
location.
LP Gas Orifice Spud Chart
Burner Rating Color Number
4,000 BTU Yellow 7OL
7,000 BTU Black 81L
9,100 BTU Green 97L
14,000 BTU Red 111L
5. Replace the Natural gas orifice spud with the correct LP gas
orifice spud. See the “LP Gas Orifice Spud Chart.”
Replace burner base and hand tighten the screws.
Replace burner cap.
Repeat steps 1 through 7 for the remaining burners.
Place Natural gas orifice spuds in plastic parts bag for future
use and keep with literature package.
10. Replace burner grates.
oe
ONO
20
11. Complete installation. See “Make Gas Connection” and
Electronic Ignition System” sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame 14"
to Ye" long. The outer cone is not as distinct as the inner cone.
LP gas flames have a slightly yellow tip.
IMPORTANT: You may have to adjust the “LO” setting for
each cooktop burner.
Di op dex ae cag fi 3 hin, fe iy, Bly BP ge Woe o,f,
Natural Gas Conversion
AWARNING
v
da
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Turn manual shutoff valve to the closed position.
A. To range
B. Shutoff valve (closed position)
C. Gas supply line
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator
1. Locate gas pressure regulator at the rear of the range.
A. Gas pressure regulator
IMPORTANT: Do not remove the gas pressure regulator.