Klein Tools 56412 User manual

1
56412
Rechargeable Flashlight with Worklight - Instructions
Linterna Recargable con Luz de Trabajo - Instrucciones
Lampe de poche rechargeable avec lampe de travail - Instructions
ENGLISH
8
FIG. A
CONTENTS
•56412 Rechargeable Flashlight with Worklight
•19" USB-C Cable
•Instruction Manual
GENERAL SPECIFICATIONS
• Battery Cell Type: 18650
•Cell Chemistry: Lithium-Ion
•Operating/Storage Altitude: 6562 ft. (2000 m)
•Operating/Charging Temperature: 32° to 104°F
(0° to 40°C)
•Storage Temperature: -22° to 140°F (-30° to 60°C)
(up to 3 months)
•Storage Humidity: <75% Relative humidity
•Relative Humidity: <85% non-condensing
•Charging Time: Charge from empty to full in 6 hours
•Shelf Life: Charge every 3 months
•Life Expectancy: Up to 500 charging cycles typical
(depending on use & care)
•Battery Capacity: 2600mAh
•Charging Requirements: Max 5.0V D.C, Min .650A
•Drop Protection: 6 ft. (2 m)
•Ingress Protection Rating: IP66
•Standards:
REACH, RoHS, CE-EMC, CEC
Specifications subject to change.
WARNINGS
Read, understand, and follow these instructions
to ensure safe operation. Failure to observe these
warnings can result in risk of fire, electric shock,
serious injury and/or property damage.
•Use of a power supply, charger, or cable not
recommended or sold with this unit may result in a
risk of fire or injury to persons.
•
DO NOT use the product if it is damaged or modified.
Damaged or modified batteries may exhibit unpredictable
behavior resulting in fire, explosion, or injury.
• DO NOT subject to vibration, impacts, or drops. The
housing may not show signs of damage, but internal
components may have been compromised. It is
advisable to replace the unit if any such severe events
occur.
•DO NOT expose to direct sunlight, open flame, heat
sources, equipment that produces heat, or extremes
in environmental temperature.
•Keep away from high voltage devices.
•DO NOT attempt to repair the flashlight or charging
cable. There are no user-serviceable parts.
•DO NOT immerse in water or other liquids. Avoid
spilling liquids or falling foreign objects into openings
on the unit.
•Risk of fire and burns. DO NOT open, crush,
heat above manufacturer’s specified maximum
temperature or incinerate.
•Properly seal the charging port cover to achieve
specified water & foreign object ingress protection
Keep seal free of dirt, oil, sand, or other material that
interferes with proper sealing. Failure to do so can
result in risk of fire or electric shock.
•DO NOT open the charging port cover if wet or in a
wet environment. Thoroughly dry the unit and the
seal around water-resistant cover completely before
opening water-resistant cover.
•When the flashlight is in use or charging, make
sure there is adequate space to allow ventilation of
internally generated heat.
•Use safety-rated power supply or wall adapter. Never
use power supply or wall adapter that exceeds the
specified charging voltage and current.
•Route the power supply cable so that it will not to be
stepped on or pinched by other objects.
•Follow Manufacturer’s Instructions.
•DO NOT attempt to insert other USB connector types
into USB-C port.
•
DO NOT attempt to remove or replace the 18650 Battery
FEATURE DETAILS (FIG. A)
1
Flashlight
5
Battery Level Indicator
2
Glow Ring
6
USB Charging Port
3
Worklight
7
Pocket Clip
4
Power button
8
USB-C Charging Cable
.
4
3
2
6
7
5
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30

ENGLISH
SYMBOLS ON PRODUCT
Warning or Caution
Risk of Electrical Shock
Read Instructions
WEEE – Battery disposal
BC
Conforms with BCS Regulations of
California Energy Commission
Conformité Européenne. Conforms with
European Economic Area directives
Direct Current (DC)
MAINTENANCE
CLEANING: Disconnect the device from all power
sources and devices prior to cleaning. Use clean, dry,
soft, lint-free cloth to wipe down the entire unit. DO
NOT use abrasive cleaners or solvents.
STORAGE: If storing for more than 1 month, charge
completely before storage, and recharge approximately
every 3 months to avoid full discharge. Store in cool
temperatures, mild humidity, and away from direct
sunlight (See GENERAL SPECIFICATIONS). Leaving the
unit in a vehicle or other confined spaces in extreme
hot temperatures can lead to decrease in service life,
overheating, or fire. Extreme cold temperatures below
the specified storage range can also harm performance
and service life. Keep away from corrosive chemicals
and gases. After taking out of storage, inspect
visually to make sure device and all accessories look
satisfactory. Allow unit to return to ambient conditions
before recharging or charging other devices.
RECHARGING: Recharge as needed. There are no
predesignated intervals at which to recharge as long
as youare using the unit regularly. Avoid discharging
completely on a regular basis, as this can impact overall
life. Regularly inspect ports and charging cable for any
debris, dirt, damage, and corrosion. DO NOT attempt to
fix. Replace device and/or cable as needed.
OPERATING INSTRUCTIONS
Read these instructions carefully before operating and
keep for future reference.
CHARGING BATTERY
•To access the charging port, twist the collar just
below the flashlight head. After charging, please
return the collar to the closed position to protect the
charging port.
• Connect USB-C cable connection to the flashlight;
plug the other end of cable into USB (2.0 or higher)
port, or AC adapter (not included). USB adapter/
power supply should not exceed the specified
charging voltage and current (Max.5.0V DC, min.
0.650A).
• The battery level indicator will illuminate:
– Solid Green: 100% charge
– Blinking Red: 0-99% charge
• A full charge could take up to 6 hours, depending on
the charger’s output. Charge completely before using.
To maximize battery life, see MAINTENANCE section
(other side).
• NOTE: Rapidly blinking yellow light while charging
indicates that 56412 is not within safe charging
temperature and is not charging
DISCHARGING BATTERY
• Battery indicator shows for 5 seconds when powered
on.
POWER ON/OFF BUTTON
• To activate the flashlight, press and release the power
button. The unit will be in HIGH flashlight mode.
• Hold down the power button to change between
flashlight and worklight modes. Once the desired
mode is on, clicking the power button will reduce the
brightness.
• NOTE: If the light is on for more than 5 seconds in
any mode, the next button press will power the light
off.
• This saves the time clicking through modes to power
down.
• NOTE: The light will turn on in the same mode last
used, when turned off.
MOUNTING OPTIONS
• The magnet on the endcap can be mounted onto any
ferrous surface.
• The pocket clip can be removed by unscrewing the
endcap.
TROUBLESHOOTING
• 56412 will NOT recharge IF: The cable is not properly
connected to charger output or battery input. Check
connection.
– The charging cable is damaged. Replace with
equivalent cable.
– The charging port or device is not able to supply
the minimum voltage and current for charging.
Connect to appropriate charging source.
– When the unit is running and battery reaches less
than 15% charge, the light will blink 3 times to
indicate low battery. The unit will do this every time
it is turned on until it is recharged.
www.calcert.com [email protected]1.800.544.2843 0
5
10
15
20
25
30