Klipsch SW12-I User manual

SERVICE MANUAL
Subwoofer Amplifier Model:
SW12-I
SW15-I
KLIPSCH, INC.

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
TABLE OF CONTENTS
SPECIFICATIONS .......................................................................................................................................2
Model: SW12-I ...........................................................................................................................................2
Model: SW15-I ...........................................................................................................................................2
THEORY OF OPERATION....................................................................................................................... 3
INPUTS ...................................................................................................................................................... 3
SIGNAL CONDITIONING ......................................................................................................................... 3
COMPRESSION......................................................................................................................................... 3
DRIVER CIRCUIT ..................................................................................................................................... 3
OUTPUT .................................................................................................................................................... 3
OTHER FEATURES................................................................................................................................... 4
ALIGNMENT PROCEDURES .................................................................................................................. 5
Model: SW12-I .......................................................................................................................................... 5
Model: SW15-I .......................................................................................................................................... 6
TROUBLE SHOOTING GUIDE................................................................................................................ 7
SW12 PARTS LIST...................................................................................................................................... 9
SW15 PARTS LIST.................................................................................................................................... 12
SCHEMATICS ........................................................................................................................................... 15
Model: SW12-I ........................................................................................................................................ 15
Model: SW15-I ........................................................................................................................................ 18
Page 1

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
Specifications
Model: SW12-I
Input Sensitivity for max Rated Output: Line input 60mVrms @ 30Hz.
Speaker input 700mVrms @ 30Hz.
Maximum Rated Output: 150 Watts into 8 ohms.
Max. Hum: 3.5mV @ 60Hz.
Max. Distortion: 4% At Full Rated Output.
Freq Response: 27 to 120Hz +0/-3dB w/12dB per Octave Rolloff.
Bass Boost: +6dB Boost @ 30Hz.
Low Pass Crossover: Variable from 40 - 120 Hz.
24 dB/Octave slope above 120 Hz.
High Pass Crossover: Line outputs fixed at 80 Hz, 6dB/Octave slope.
Speaker outputs fixed at 120 Hz, 6dB/Octave slope.
Model: SW15-I
Input Sensitivity for Max Rated Output: Line input 33mVrms @ 30Hz.
Speaker input 900mVrms @ 30Hz.
Maximum Rated Output: 200 Watts into 4 ohms.
Max. Hum: 3.5mV @ 60Hz.
Max. Distortion: 4% At Full Output.
Freq Response: 27 to 120Hz +0/-3dB w/12dB per Octave Rolloff.
Bass Boost: +6dB Boost @ 30Hz.
Low Pass Crossover: Variable from 40 - 120 Hz.
24 dB/Octave slope above 120 Hz.
High Pass Crossover: Line outputs fixed at 80 Hz, 6dB/Octave slope.
Speaker outputs fixed at 120 Hz, 6dB/Octave slope.
Page 2

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
THEORY OF OPERATION
SW12, & SW15 Series I Amplifiers
INPUTS
There are two types of inputs and passive outputs. Four RCA jacks for LINE LEVEL left
and right inputs and outputs and a panel of SPEAKER LEVEL inputs and outputs for left and right
stereo channels. The SPEAKER LEVEL inputs have a high pass filter on each channel that allows
frequencies above 120 Hz to go directly to the main speakers of the system. Frequencies below
120 Hz go through the subwoofer amplifier and on to the woofer. The LINE LEVEL inputs also
use a high pass filter that allows frequencies above 80 Hz to go back out to a system amplifier.
Frequencies below 80 Hz go through the subwoofer amplifier and on to the woofer. Both filters
have a 6dB per octave rolloff.
SIGNAL CONDITIONING
The first op-amp of U1, a quad op-amp IC, is a summing amp for the RCA and SPEAKER
level inputs. The LEVEL adjustment is located between the first and second op-amp stages of U1.
The second op-amp of U1 is a buffer stage with a gain of 1. The third op-amp of U1 is a High
pass filter configuration. The fourth op-amp of U1 is used to adjust phase from 0° to 180°. The
next circuit is an adjustable RC filter for low pass filtering from 40Hz to 120Hz consisting of U2 and
U4.
COMPRESSION
The compression circuit consists of U5, U6, and Q28 and is adjusted via R30. If adjusted
correctly, this circuit will limit the amplitude of the signal so the minimum amount of distortion in the
form of clipping will occur at the output of the amplifier. R34 is used to set the maximum output
level for the amplifier so it doesn’t underamplify or clip. Next, the signal goes through a buffer
amplifier U2, which provides a gain of 4. Then the signal goes on to the driver circuits.
DRIVER CIRCUIT
The driver circuit consists of Q1 through Q12 and is located on the Filter/Driver board.
The driver circuit has a DC offset adjustment, R50, which should be set at 0 Vdc +/- 50mVdc. This
can be measured across the + and - output wires (white & black respectively) from the amp
with power on and no signal applied. The driver circuit is a Class AB amplifier.
OUTPUT
The output section of this amplifier uses discrete components Q15 through Q26 to obtain
the high power output required. The output amplifier circuit is a Class AB complementary
symmetry configuration with three sets of four transistors cascaded. This provides high power
output into a low impedance load. The components for the output circuit is located on the Power
Board.
POWER SUPPLIES
The main power supply circuit is unregulated and supplies +/- 81 Vdc for the output and
driver circuits. The +/- 81 Vdc is then divided and regulated by 34V zener diodes to supply +/- 34
Vdc to bias the driver circuit. There is a second power supply which is fed by a second set of taps
off of the transformer. This is the regulated +/- 15 Vdc for the op-amps on the filter board.
Page 3

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
OTHER FEATURES
This amplifier uses a control circuit to control the operation of the output relay. When
power is first applied the circuit provides a delay before activating the relay. This is a protection
feature to protect the speaker and amplifier from initial current surges. The circuit also provides
protection from over-current conditions by de-activating the relay when excessive output current is
sensed. The relay and it’s control circuitry is located on the Filter/Driver Board and consists of
U11, U12, RLY 1 and R131. R131 is used to set the threshold level for over-current sensing.
Page 4

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW12-I AMPLIFIER ALIGNMENT PROCEDURE
CAUTION!
Lethal voltages are present and exposed when cover is off of amplifier.
1
Only qualified service technicians should attempt to repair or align subwoofer amplifiers.
Equipment required:
A signal source capable of supplying a 30Hz sine wave at 300mVrms.
A true RMS Voltmeter such as the Fluke 8060B.
A 16 ohm load rated for at least 200 Watts.
An oscilloscope (optional).
To totally align SW12 series 1 amplifiers, follow this procedure:
1. Disconnect power from the UUT (unit under test).
2. Connect the UUT (unit under test) to a 16 ohm load.
3. Connect a signal generator to the RCA input of the amp.
4. Set all controls on the UUT to their full clockwise position.
5. Set the signal generator for 30Hz and 60mVrms output.
(be sure and measure the output of the generator for 60mVrms.)
6. Connect the voltmeter leads to the output of the UUT.
7. Apply power to the UUT.
8. Adjust R34 for 33Vrms. Range is from 32.1 Vrms to 34 Vrms.
9. Change signal level to 1.5mVrms @ 30Hz .
10. Measure the output voltage. Should be between .94 Vrms and 1.06Vrms.
Adjust R30 if necessary.
* NOTE: Some interaction between adjustments is common. Recheck steps 8 and 10 for
proper voltages.
11. Alignment of the UUT is now complete. Disconnect power and other
connections from the UUT.
Page 5

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW15-I AMPLIFIER ALIGNMENT PROCEDURE
CAUTION!
Lethal voltages are present and exposed when cover is off of amplifier.
1
Only qualified service technicians should attempt to repair or align subwoofer amplifiers.
Equipment required:
A signal source capable of supplying a 30Hz sine wave at 300mVrms.
A true RMS Voltmeter such as the Fluke 8060B.
A 16 ohm load rated for at least 300 Watts.
An oscilloscope (optional).
To totally align SW15 series 1 amplifiers, follow this procedure:
1. Disconnect power from the UUT (unit under test).
2. Connect the UUT (unit under test) to a 16 ohm load.
3. Connect a signal generator to the RCA input of the amp.
4. Set all controls on the UUT to their full clockwise position.
5. Set the signal generator for 30Hz and 33mVrms output.
(be sure and measure the output of the generator for 33mVrms.)
6. Connect the voltmeter leads to the output of the UUT.
7. Apply power to the UUT.
8. Adjust R34 for 29.5Vrms. Range is from 29.1Vrms to 30.1Vrms.
9. Change signal level to 1.5mVrms @ 30Hz .
10. Measure the output voltage. Should be between 1.19 Vrms and 1.33Vrms.
Adjust R30 if necessary.
* NOTE: Some interaction between adjustments is common. Recheck steps 8 and 10 for
proper voltages.
11. Alignment of the UUT is now complete. Disconnect power and other
connections from the UUT.
Page 6

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
TROUBLE SHOOTING GUIDE
CAUTION!
Lethal voltages are present and exposed when cover is off of amplifier.
1
Only qualified service technicians should attempt to repair or align subwoofer amplifiers.
PROBLEM POSSIBLE CAUSE
1Blows fuse with nothing connected 1 Check output transistors on power board.
to the output. Replace transistors that are shorted.
2 Check driver transistors on filter/driver board.
Replace transistors that are shorted.
3 Check U7 and U9 for shorts.
4 Check bridge rectifier in power supply circuit.
5 Check transformer.
6 Check filter capacitors. C21,C22, C23, C24, C44, C45,
C46, and C47.
7 Check for pinched wires going to and coming from
the transformer.
2 Low output level using speaker level 1 Check inputs for correct polarity from source.
inputs. If polarity is not correct, the signals will be 180° out of phase
and will cancel each other out causing a low output.
2Check R79 and R80.Should read 91K:.
3 Check U13.
4 Check for proper signal flow using schematic.
Page 7

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
TROUBLE SHOOTING GUIDE(continued)
PROBLEM POSSIBLE CAUSE
3Causing popping sound. 1 Connect amplifier output to a 16 ohm load.
Apply a 60mVrms 30Hz signal to one RCA jack.
The voltage across the load should be between
32.1 Vrms and 34 Vrms for SW12.
29.1 Vrms and 30 Vrms for SW15.
For the THX amp., apply a 3Vrms 70Hz signal to one
RCA jack. The voltage across the load should be
between 35.1 Vrms and 36 Vrms.
If this is correct, connect an oscilloscope to the
output signal and look for clipping.
If the voltage was too high, re-align amplifier per procedure
on page 5, 6, or 7.
If the signal was clipped, re-adjust the amplifier per
alignment procedure on page 5, 6, or 7.
4 Excessive hum. 1 Check all ground connections.
2 Check all filter capacitors. C21, C22, C23, C24,
C44, C45, C46, and C47.
5 Amplifier quits working after a short 1 Check for excessive heat on heat sink. This indicates a
period of time. a bad output device or a bad thermal switch.
2 Check output relay (RLY1).
3 Check U11 and U12.
Page 8

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW12-I PARTS LIST
PART VALUE/PART NUMBER KLIPSCH PART #
LEVEL CONTROL 10K VARIABLE
LOWPASS ADJUST 50K VARIABLE, DUAL
PHASE ADJUST 100K VARIABLE
R1, R2, R3, R128, R137, R138 15K
R12, R11 47K
R13, R35, R36, R133, R134 22K
R132 2.2 Meg
R139 39K
R14, R21 6.65K
R15 20K
R16, R18, R19, R40, R41, R127 10K
R17 5.23K
R20 2K
R22 30.1K
R28, R29 220K
R30, R34, R50 10K VARIABLE
R31, R32, R37 100K
R33, R42, R68, R71 100:
R38 43K 2%
R39 180K 2%
R43, R44 10K 2%
R6, R8, R46 4.7K
R47, R53 4.3K 3WATT
R9 0:
R49 33.2K
R51, R67 1K
R54, R62 1.1K
R55, R63 300:
R56, R61 11.5K
R57, R58, R59, R60 220:
R6, R8 510:2WATT
R64, R69 511:
R65, R70, R73, R75 22.1:
R66 39.2K
R72, R74 2.7K 3WATT
R10 91K
R45 1M:
R7 47:
R4, R5 300K
C1, C2 .22µF
C10, C27, C30 .1µF
C11 .12µF
C15, C53 .047µF
C16, C17, C19 1µF 25V Electrolytic
C20 .01µF
C5 .001µF
C29 2.2µF
C3, C4 150µF 100V NON-POLAR
C32, C33 470µF 50V Electrolytic
C34, C35 22pF
Page 9

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW12-I PARTS LIST(continued)
PART VALUE/PART NUMBER KLIPSCH PART #
C36, C37, C39, C40 330pF
C6 4.7µF 25V Electrolytic
C55 10µF 63V Electrolytic
C18 10µF 25V Electrolytic
C7 .0027µF
C8, C9 1µF
D18 1N914B
D5, D6 1N4752A Zener
U1 MC4741 118744
U2, U4 MC1458N 118743
U5 NE570 118745
U6 LM393 118742
Q1, Q2, Q11 MPS8099 118735
Q28 2N3906 118728
Q3, Q4, Q12 MPS8599 118736
Q5 MPSW56 118738
Q6 MPSW06 118737
Q7, Q9 2SA1306B 118730
Q8, Q10 2SC3298B 118732
R100, R101, R102, R103, R110, R111, R112, R113 .47:5WATT
R114 4.7:3WATT
R115 1:3WATT
R116, R121, R126, R130 10K
R117, R119 56K
R118 22K
R120 390:1WATT
R122, R123 100K
R125 68:
R131 10K Variable
R135 1.8K
R136 6.8K
R76, R77 15:1WATT
R82 150:
R83 100:
R84 100:Variable
R87, R88, R89, R90 1.5K 5WATT
R91, R92 51:
R93 22.1:
R94, R95, R98, R99, R104, R105, R108, R109 1.2:1/2WATT
C21, C22 1000µF 35V Electrolytic
C23, C24 1µF 25V Electrolytic
C28, C31 470µF 100V Electrolytic
C43 100µF 10V Electrolytic
C44, C45, C46, C47 4700µF 100V Electrolytic
C48 .1µF
C49 33µF 50V Electrolytic
C50 4.7µF 50V Electrolytic
C52 330µF 16V Electrolytic
Page 10

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW12-I PARTS LIST(continued)
PART VALUE/PART NUMBER KLIPSCH PART #
C54 10µF 25V Electrolytic
C56 .1µF 125Vac
D1, D2, D3, D4, D11, D12 1N4002
D13, D14, D15, D16, D17 1N914
Q15, Q18 MJF15030 118733
Q16, Q17, Q19, Q20 2SC3281 118731
Q21, Q24 MJF15031 118734
Q22, Q23, Q25, Q26 2SA1302 118729
Q27 MPSA06
U11 UPC1237 118746
U12 MC1458 118743
U7 7815 118739
U9 7915 118740
L1 2µH
F2, F3 JUMPER
RLY1 AROMAT J51E-12 (Relay)
RCA PANEL
SPEAKER INPUT JACKS
TRANSFORMER PW-6582 118721
SW2 (Power)
F1 5 Amp 250Vac Slow Blow 118348
TH1 (Thermal protection) ASAH US-602S
BR1 GBPC 3502
DUAL VOLTAGE TRANSFORMER PW-6661 118725
DUAL VOLTAGE SWITCH 115 to 230
CAPACITOR (DUAL VOLTAGE MODEL) .047µF 300V
Page 11

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW15-I PARTS LIST
PART VALUE/PART NUMBER KLIPSCH PART #
LEVEL CONTROL 10K VARIABLE
LOWPASS ADJUST 50K VARIABLE, DUAL
PHASE ADJUST 100K VARIABLE
R1, R2, R3, R128, R137, R138 15K
R12, R11 47K
R13, R35, R36, R133, R134 22K
R132 2.2 Meg
R139 39K
R14, R21 6.65K
R15 20K
R16, R18, R19, R40, R41, R127 10K
R17 5.23K
R20 2K
R22 30.1K
R28, R29 220K
R30, R34, R50 10K VARIABLE
R31, R32, R37 100K
R33, R42, R68, R71 100:
R38 43K 2%
R39 180K 2%
R43, R44 10K 2%
R6, R8, R46 4.7K
R47, R53 4.3K 3WATT
R9 0:
R49 33.2K
R51, R67 1K
R54, R62 1.1K
R55, R63 300:
R56, R61 11.5K
R57, R58, R59, R60 220:
R6, R8 510:2WATT
R64, R69 511:
R65, R70, R73, R75 22.1:
R66 39.2K
R72, R74 2.7K 3WATT
R10 120K
R45 1M:
R7 47:
R4, R5 300K
C1, C2 .22µF
C10, C27, C30 .1µF
C11 .12µF
C15, C53 .047µF
C16, C17, C19 1µF 25V Electrolytic
C20 .01µF
C5 .001µF
C29 2.2µF
C3, C4 150µF 100V NON-POLAR
C32, C33 470µF 50V Electrolytic
C34, C35 22pF
Page 12

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW15-I PARTS LIST(continued)
PART VALUE/PART NUMBER KLIPSCH PART #
C36, C37, C39, C40 330pF
C6 4.7µF 25V Electrolytic
C55 10µF 63V Electrolytic
C18 10µF 25V Electrolytic
C7 .0027µF
C8, C9 1µF
D18 1N914B
D5, D6 1N4752A Zener
U1 MC4741 118744
U2, U4 MC1458N 118743
U5 NE570 118745
U6 LM393 118742
Q1, Q2, Q11 MPS8099 118735
Q28 2N3906 118728
Q3, Q4, Q12 MPS8599 118736
Q5 MPSW56 118738
Q6 MPSW06 118737
Q7, Q9 2SA1306B 118730
Q8, Q10 2SC3298B 118732
R100, R101, R102, R103, R110, R111, R112, R113 .47:5WATT
R114 4.7:3WATT
R115 1:3WATT
R116, R121, R126, R130 10K
R117, R119 56K
R118 22K
R120 390:1WATT
R122, R123 100K
R125 68:
R131 10K Variable
R135 1.8K
R136 6.8K
R76, R77 15:1WATT
R82 150:
R83 100:
R84 100:Variable
R87, R88, R89, R90 1.5K 5WATT
R91, R92 51:
R93 22.1:
R94, R95, R98, R99, R104, R105, R108, R109 1.2:1/2WATT
C21, C22 1000µF 35V Electrolytic
C23, C24 1µF 25V Electrolytic
C28, C31 470µF 100V Electrolytic
C43 100µF 10V Electrolytic
C44, C45, C46, C47 4700µF 100V Electrolytic
C48 .1µF
C49 33µF 50V Electrolytic
C50 4.7µF 50V Electrolytic
C52 330µF 16V Electrolytic
Page 13

Klipsch Subwoofer Amplifier Service Manual KSAMM-002a
SW15-I PARTS LIST(continued)
PART VALUE/PART NUMBER KLIPSCH PART #
C54 10µF 25V Electrolytic
C56 .1µF 125Vac
D1, D2, D3, D4, D11, D12 1N4002
D13, D14, D15, D16, D17 1N914
Q15, Q18 MJF15030 118733
Q16, Q17, Q19, Q20 2SC3281 118731
Q21, Q24 MJF15031 118734
Q22, Q23, Q25, Q26 2SA1302 118729
Q27 MPSA06
U11 UPC1237 118746
U12 MC1458 118743
U7 7815 118739
U9 7915 118740
L1 2µH
F2, F3 JUMPER
RLY1 AROMAT J51E-12 (Relay)
RCA PANEL
SPEAKER INPUT JACKS
TRANSFORMER PW-6582 118721
SW2 (Power)
F1 5 Amp 250Vac Slow Blow 118348
TH1 (Thermal protection) ASAH US-602S
BR1 GBPC 3502
DUAL VOLTAGE TRANSFORMER PW-6661 118725
DUAL VOLTAGE SWITCH 115 to 230
CAPACITOR (DUAL VOLTAGE MODEL) .047µF 300V
Page 14