KLOCK WERKS Kicker PXA 200.2 User manual

KICKER AMP & SPEAKER
INSTALLATION GUIDE
FOR USE WITH HARLEY DAVIDSON 2014+ FLHT
> Step-by-step Installation Guide
> 6 1/2” Kicker Speakers Pair
> Kicker Amp 200W
> Stainless Steel Mounting Bracket
> Custom Wiring Harness
> All Necessary Hardware
- 8 - 32 x 1/2” Button Head Bolts
- 8 - 32 Nylock Nuts
- Black Heat Shrink
- Black Cable Tie
- Mounting Hardware
INCLUDED IN THIS FIT KIT:
4405-FLHT1401R1 ©2016 KLOCK WERKS

GETTING STARTED
1. Remove the seat and disconnect the battery
2. Remove the passing lamps/turn signals
a. Loosen and remove both fasteners and unplug each passing lamp/turn signal
3. Remove the windshield
4. Remove the outer fairing
a. Remove the four mounting screws, unplug the headlamp and set aside on a soft cloth
5. Remove the fuel tank
a. Remove the console
b. Unplug the fuel fitting on the left side
c. Remove all four mounting bolts and carefully lift the tank off the bike and set aside
6. Remove wire caddy cover
a. Carefully release each tab along the caddy until it lifts completely
SPEAKER INSTALLATION
1. Remove one of the white speaker pods from the inner fairing
a. There are five fasteners in the center portion and three on the outside to release it from the inner fairing (1)
2. Remove the stock speaker and replace with the PSC652 speaker from the kit
a. Install provided foam gasket material to the back side of each speaker (2)
b. Install the provided speaker ring adapter onto the speaker pod (3)
c. Install the speaker into the pod and fasten with the original speaker screws (4)
3. Reinstall the pod to the inner fairing
4. Repeat for the other side
Note: There may be some connectors that will need to be relocated off of the radio chassis for the amp bracket to fit
KLOCK WERKS | FLHT KICKER AMP AND SPEAKER INSTALLATION
IMPORTANT INSTALLATION NOTE:
Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper procedures and
torque specifications. We cannot be responsible for damage resulting from improper installation techniques. This kit may not be compatible with
some aftermarket head units.
21 3
4

AMP INSTALLATION
7. Fasten the amplifier to the bracket with the supplied hardware.
a. Insert the bolts through the bottom of the bracket and install the locknuts to the amplifier
8. Using the supplied ¼” hardware, fasten the amp/bracket assembly to the radio chassis with the 12 pin connector
facing the clutch side
HARNESS INSTALLATION
9. Plug the harness into the amplifier and route the speaker wires to their respective locations (1)
a. Separate the speaker connectors and plug in the amplifier harness to each speaker
10. Plug the switched power harness into the 2-place amp connector on the right side (2)
11. Plug the blue wire on the kicker harness into the switched power harness lead with one wire
a. This allows for an accessory 12V port to remain available
12. Route the power leads along the left side of the frame neck, in the electrical caddy to the seat area. (3)
13. Connect the battery terminals and check system function
SYSTEM SETUP
Note: At this time, it is highly recommended to follow the guidelines in your Kicker PXA200.2 owner’s manual to set up the amplifier.
Klock Werks recommends that the dip switches be set up as follows:
1. Auto turn-on - 12V
2. Input level - HI
3. HI-PASS – 80 Hz
4. Input Gain control – Follow the instructions in your Kicker PXA 200.2 owner’s manual
14. Test component function and set the gain according to the Kicker PXA 200.2 manual
15. Carefully reassemble the motorcycle and enjoy your new audio kit!
NOTE: It is now necessary to utilize either your local Harley-Davidson dealer for the use of the Digital Tech software OR a motorcycle
shop equipped with a similar program to set up the infotainment system to recognize your new amplifier.
KLOCK WERKS | FLHT KICKER AMP AND SPEAKER INSTALLATION (CONTINUED)
12 3
MAKE SURE GAIN SETTING ON AMPLIFIER IS SET TO 0