Knape&Vogt MUV 22 User manual

SPECIFICATIONS
Number: Full Extension Soft-Close Undermount Drawer Slide
Mounting: Side, for Frame or Frameless Construction
Height: 1-7/8"
Load Rating: 75-Pound Class
Finish: Zinc
Travel: Full Extension
Sizes: 9", 10", 12", 14", 15", 16", 18", 20", 21", 22"
Packaged: Bulk (B): 6 Sets per Carton. Includes Front Release Levers (14"+).
Bulk (B): 4 Sets per Carton. Includes Front Release Levers (9",10",12").
Rear Brackets: MUV-RBM Metal Rear Bracket (for use on 14",15",16",18",20",21",22" Slides). 12 Brackets (Unhanded).
MUV-RBP Plastic Rear Brackets (for use with 9",10",12" Slides). 8 Brackets (4 Right Hand, 4 Left Hand).
Fasteners: MUV-122: #7 x 5/8"Flat Head Screw – Slide
MUV-123: #6 x 1/2"Truss Head Screw – Front Release Levers and Rear Bracket
Install Jig: MUV-121
DRAWER ASSEMBLY
DRAWER HARDWARE INSTALLATION
31/32"
[24.6mm] 29/32"
[23mm]
1/4" [6.3mm]
Variable
Drawer Bottom
Drawer Bottom
Pre-drill front holes
at 15º angle.
1
Release Lever Adjustment (1/8")
(Vertical Adjustment)
Optimal Operation Guidelines for Drawer Width Based on Drawer Height:
Drawer Height up to 6": Max. Width = Slide Length + 10"
Drawer Height Greater than 6": Max. Width = Slide length + 10" or 28",
whichever is less
Drawer Height Greater than 8": Max. Width = Slide Length + 10" or 24",
whichever is less
Drawer Height Greater than 10": Max. Width = Slide Length + 10" or 21",
whichever is less
Material Thickness
For use with the following
material thicknesses:
5/8" [16mm]
9/16" [14mm]
1/2" [13mm]
Full Extension Soft-Close
Undermount Drawer Slide
If material is less than 1/2" drawer length
must be sized shorter by same amount.

FACE FRAME APPLICATIONS [WITH DECORATIVE FRONT]
Cabinet Depth
Interior Depth
Slide Length
Bracket:
3/16" to 1-7/8" [5mm to 48mm] Slides 14" +
3/16" to 1-1/16" [5mm to 27mm] Slides 9" to 12"
Setback 5/32" [4mm]
Mount Position
3/8" [10mm]
1-7/16"
[37mm]
31/32"
[25mm]
Min. Top Gap
1/4" [6mm]
Max. Drawer Height=
Opening minus 13/16"
[20mm]
Bottom
Recess
1/2" max.
[12.7mm]
Bottom Clearance
9/16" [14mm]
Drawer Gap
1/32" [1mm]
Interior Depth Range
Variable Setback
Face Frame Inset Application
Drawer Length
SLIDE CABINET DEPTH SLIDE LENGTH DRAWER LENGTH MAX INTERIOR DEPTH MIN INTERIOR DEPTH MAX. MATERIAL THICKNESS SETBACK
MUV 22 24" [610mm]*22.4" [569mm] 22" [559mm]** 24-9/16" [624mm] 22-7/8" [581mm] 5/8" [16mm] 5/32" [4mm]
MUV 21 24" [610mm] 21.4" [544mm] 21" [533mm]** 23-9/16" [598mm] 21-7/8" [555mm] 5/8" [16mm] 5/32" [4mm]
MUV 20 24" [610mm]*20.4" [518mm] 20" [508mm]** 22-9/16" [573mm] 20-7/8" [530mm] 5/8" [16mm] 5/32" [4mm]
MUV 18 21" [533mm] 18.4" [467mm] 18" [457mm]** 20-9/16" [522mm] 18-7/8" [479mm] 5/8" [16mm] 5/32" [4mm]
MUV 16 21" [533mm]*16.4" [417mm] 16" [406mm]** 18-9/16" [472mm] 16-7/8" [429mm] 5/8" [16mm] 5/32" [4mm]
MUV 15 18" [457mm] 15.4" [391mm] 15" [381mm]** 17-9/16" [446mm] 15-7/8" [403mm] 5/8" [16mm] 5/32" [4mm]
MUV 14 18" [457mm]*14.4" [366mm] 14" [356mm]** 16-9/16" [421mm] 14-7/8" [378mm] 5/8" [16mm] 5/32" [4mm]
MUV 12 15" [381mm] 12.4" [315mm] 12" [305mm]** 13-3/4" [349mm] 12-3/4" [324mm] 5/8" [16mm] 5/32" [4mm]
MUV 10 12" [305mm] 10.15" [258mm] 10" [254mm]** 11-3/4" [298mm] 10-3/4" [273mm] 5/8" [16mm] 5/32" [4mm]
MUV 9 12" [305mm] 10.15" [258mm] 9" [229mm]** 11-3/4" [298mm] 10-3/4" [273mm] 5/8" [16mm] 5/32" [4mm]
2
Setback
Setback = Drawer Front Thickness + 3/16" [5mm]
Depth Range
Min. = Slide Length + Setback + 3/16" [5mm]
Max. = Slide Length + Setback + 1-15/16" [49.2mm] Slides 14"+
Max. = Slide Length + Setback + 1-1/16" [27mm] Slides 9",10",12"
1-1/4"
[32mm]
1-5/16"
[33mm]
1/4"
[6mm]
1-7/16"
[37mm]
31/32"
[25mm]
11/32"[9mm]
TYP.
Slide Front Detail
*When using rear bracket at maximum extension.
Full Extension Soft-Close Undermount Drawer Slide
Rear Slide Detail
11/32"
[9mm]
TYP
1-15/32"
[37.5mm]
1-7/16"
[37mm] TYP. 31/32"
[25mm] TYP. 11/32"
[9mm]
L
**If material is less than 1/2” drawer length must be sized shorter by same amount.

1-1/4"
[32mm]
1-5/16"
[33mm]
1/4"
[6mm]
1-7/16"
[37mm]
31/32"
[25mm]
11/32" [9mm]
TYP.
Slide Front Detail
FRAMELESS APPLICATIONS [WITH DECORATIVE FRONT]
Cabinet Depth
Interior Depth
Slide Length Setback 5/32” [4mm]
Mount Position
1-7/16" [37mm]
1-7/16"
[37mm]
31/32"
[25mm]
Min. Top Gap
1/4" [6mm]
Max. Drawer Height=
Opening minus 13/16"
[20mm]
Bottom
Recess
1/2" [12.7mm]
Bottom Clearance
9/16" [14mm]
Drawer Gap
1/32" [1mm]
Variable Setback
Interior Depth Range
Frameless Inset Application
SLIDE CABINET DEPTH MIN INTERIOR DEPTH SLIDE LENGTH DRAWER LENGTH A B C MAX. MATERIAL
THICKNESS SETBACK
MUV 22 24" [610mm] 22-3/4" [578mm] 22.4" [569mm] 22" [559mm]** 10-5/64" [256mm] 8-13/16" [224mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 21 24" [610mm] 21-3/4" [553mm] 21.4" [544mm] 21" [533mm]** 10-5/64" [256mm] 8-13/16" [224mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 20 21" [533mm] 20-3/4" [527mm] 20.4" [518mm] 20" [508mm]** 8-13/16" [224mm] 8-13/16" [224mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 18 21" [533mm] 18-7/8" [479mm] 18.4" [467mm] 18" [457mm]** 7-9/16" [192mm] 8-13/16" [224mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 16 18" [457mm] 16-3/4" [425mm] 16.4" [417mm] 16" [406mm]** 5-1/32" [128mm] 8-13/16" [224mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 15 18" [457mm] 15-7/8" [403mm] 15.4" [391mm] 15" [381mm]** 7-9/16" [192mm] 5-1/32" [128mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 14 15" [381mm] 14-3/4" [375mm] 14.4" [366mm] 14" [356mm]** 7-9/16" [192mm] 5-1/32" [128mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 12 15" [381mm] 12-7/8" [326mm] 12.4" [315mm] 12" [305mm]** 3-25/32" [96mm] 5-1/32" [128mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 10 12" [305mm] 10-3/4" [273mm] 10.15" [258mm] 10" [254mm]** 3-25/32" [96mm] 3-25/32" [96mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
MUV 9 12" [305mm] 10-3/4" [273mm] 10.15" [258mm] 9" [229mm]** 3-25/32" [96mm] 3-25/32" [96mm] 1-1/16" [27mm] 5/8" [16mm] 5/32" [4mm]
A B
C[see chart at bottom of page] [see chart at bottom of page]
[see chart
at bottom
of page]
3
Setback
Setback = Drawer Front Thickness + 3/16" [5mm]
Min. Interior Depth
Min. = Slide Length + Setback + 1/8" [3mm]
Full Extension Soft-Close Undermount Drawer Slide
Rear Slide Detail
11/32"
[9mm]
TYP
1-15/32"
[37.5mm]
1-7/16"
[37mm] TYP. 31/32"
[25mm] TYP. 11/32"
[9mm]
Drawer Length L
**If material is less than 1/2” drawer length must be sized shorter by same amount.

KNAPE & VOGT LIMITED LIFETIME WARRANTY FOR COMMERCIAL PRODUCTS
This warranty is given to the initial purchaser of new commercial products purchased from Knape & Vogt and its subsidiaries. The warranty covers defects in materials and workman-
ship. The warranty does not apply to defects resulting from misuse, damage or abuse, normal wear and tear, accident, modification, improper installation or maintenance, third party
materials or damage during shipping. The warranty is not transferable and does not cover any subsequent purchasers of the products. During the Limited Lifetime Warranty period,
Knape & Vogt, will, at its option, repair or replace any defective product with a comparable product or component. This Limited Warranty is for repair or replacement of defective
products only and does not cover any other costs such as removal, installation, or other related expenses. For warranty service, please contact Knape & Vogt, 2700 Oak Industrial
Drive, Grand Rapids, MI 49505, Attention: Customer Service. Information regarding the claimed defect and date of purchase of the product must be provided. Any defective product
must be returned postage or freight prepaid to Knape & Vogt. THIS LIMITED WARRANTY CONSTITUTES THE ONLY WARRANTY FOR THE PRODUCTS AND ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY DISCLAIMED. THIS LIMITED WARRANTY CONSTITUTES THE SOLE REMEDY AVAILABLE WITH REGARD TO ANY DEFECTIVE
PRODUCTS. KNAPE & VOGT SHALL NOT BE LIABLE FOR ANY INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOSS OF TIME,
INCONVENIENCE, OR LOST REVENUES OR PROFITS.
Copyright © 2006 Knape & Vogt, all rights reserved. Standard KV Commercial Warranty (Rev No.2, 9/23/05)
© 2013 Knape & Vogt Manufacturer reserves the right to change specifications without notice and without incurring responsibility for existing units. US Patent 8,430,567
2700 Oak Industrial Drive NE Grand Rapids, MI 49505
800.253.1561 • 616.459.3311 • fax [phone] www.kv.com
DRAWER DIMENSIONS FOR FACE FRAME AND FRAMELESS APPLICATIONS
Cabinet Opening Width
Drawer Thickness Deduct from Opening Width
5/8" [16mm] 3/8" [10mm]
9/16" [14mm] 9/16" [14mm]
1/2" [13mm] 5/8" [16mm]
Drawer Notch & Bore Rear Brackets
1/4" x 3/8" DEEP [6mm x 10mm DEEP]
9/32"
[7mm]
1/2" Max.
[12.7mm]
1-5/16" Min.
[33mm]
7/16"
[11mm]
13/16"
[21mm]
1-1/4"
[32mm]
5/8"
[16mm]
Drawer Width Calculation
310149/0713
4
5/8"
[16mm]
Full Extension Soft-Close Undermount Drawer Slide
13/16"
[21mm]
1-1/4"
[32mm]
5/8"
[16mm]
5/8"
[16mm]
13/16"
[21mm]
MUV-RBP MUV-RBM
CRITICAL*
Inside Drawer Width
CRITICAL
Max. Drawer Bottom Recess: 12.7mm (1/2")
Min. Top Opening Clearance:
6.3mm (1/4")
Min. Bottom
Opening Clearance:
14mm (9/16")
*Cabinet Opening Width Minus 42mm (1-5/8") = Inside Drawer Width
MuV Maximum Drawer Side Material Thickness: 16mm (5/8")
Use Muv34 for Drawer Material from 16mm (5/8") to 19mm (3/4")
If material is less than 1/2",
use formula.*