KneeRover Fusion All Terrain User manual

KneeRover® Fusion All Terrain
User Manual

Congratulations on your purchase of the KneeRover®
Fusion All Terrain!
The KneeRover® Fusion All Terrain provides state of the art 4-wheel steering
technology that provides a new level of freedom to users recovering from foot,
ankle or lower leg injuries. This revoluonary product enables users to get
back to their daily rounes and enjoy life while recovering - increasing their
mobility without the use of painful crutches.
Operang Instrucons:
This medical device is designed to maximize mobility during your recovery
from foot/ankle surgery or injury.
Place the knee of your injured leg on the knee plaorm and stand as straight
as possible. Adjust the handlebar to approximately waist high or the top of
your hips. This will allow you to nd the most comfortable posion for your
hands while holding the grips. Adjust the knee plaorm height so that your
injured leg is supported at a 90 degree angle when standing.
Ensure that the hand brake is fully engaged before mounng the KneeRover®
scooter. To move the scooter, simply push forward with your good foot. Allow
the scooter to glide, and as it slows down, push again.
We recommend operang the KneeRover® scooter at a safe walking
speed (< 3 mph).
Ongoing Maintenance:
We recommend saving the tools that are provided with your KneeRover®
product, as you may need them to provide ongoing maintenance. With rou-
ne use, nuts and bolts on the KneeRover® knee walker can become loose. To
ensure safe operaon of your KneeRover® scooter, it is important to period-
ically inspect for loose nuts and bolts and re-ghten as appropriate. Ensure
that the FRONT wheels are inated to between 38 and 40 PSI. The maximum
PSI for front wheels is 40. Ensure that the REAR wheels are inated to be-
tween 33-35 PSI. Maximum PSI for rear wheels is 35.
Please visit hps://kneerover.com/pages/kneerover-maintenance-videos for
addional support in maintaining your KneeRover® product.

KneeRover® Fusion All Terrain - Tools & Parts List:
The following tools and parts are included with your KneeRover® Fusion. Please
follow assembly instrucons for your specic KneeRover® model, using the
tools and parts provided.
Assembly videos for your KneeRover® model can also be found at:
hps://kneerover.com/pages/assembly-video
Front Axle
Bolts (2)
Tie-Rod
Bolt
Tie-Rod
Nut
Tie-Rod
Washers
(4)
Cover
Bolts (4)
Cover Washers (4)
Wrench for
Tie-Rod
Assembly
Handle Bar
Height
Adjustment
Knob
Wrench for
Kneepad
Bolts and
Cover Bolts
Kneepad
Plaorm
Locking Pin
Front Axle
Bolt Wrench
Seat Washers (4) Seat Bolts (4)

KneeRover® Fusion All Terrain Set Up Instrucons:
Please follow the step by step instrucons on the following pages to properly
assemble your KneeRover® scooter. The diagram below idenes the key
components of the scooter to aid with assembly.
Visit hps://kneerover.com/pages/assembly-video for assembly videos.
Weight capacity = 350 pounds
Height Adjustment
Knob
Hand Brake with Parking
feature
Steering
Column
Brake Cable
Quick
Release
Lever
Removable Front Axle
9” All Terrain Wheels
Maximum 35 PSI
Rear Dual Disk
Brakes
Adjustable
Knee Plaorm
12” All Terrain Wheels
Maximum 40 PSI

Step 1: Install Front Axle
Please take your me to carefully complete all steps before operang your new
KneeRover® scooter. First, place the front axle with 12” wheels under the
scooter frame, ensuring the round bolts by the wheels are facing up. Align the
axle and frame holes, insert front axle bolts and ghten completely using the
allen wrench provided. Make sure the welded nuts on the front axle are facing
towards the ground.
Step 2: Install Tie Rods
The e rod ends are already aached to the spindles/wheels. Bring the le e
rod (square hole) and place over the black guide and the right e rod (round
hole) under the black guide. Insert the bolt into the top e rod so the head
of the bolt is sing ush. Next, insert the bolt through the washer and black
guide. Place another washer on the e rod bolt under the black guide and then
the bolt through the right e-rod round hole. Next, place two washers onto the
e-rod bolt from the boom and then the locking nut. Aer the e rods are
assembled, ghten the locking nut unl it barely touches the boom washer.
Take care not to over ghten the locking nut, as this could cause some
resistance while turning the knee walker. Below is a picture of a properly as-
sembled Tie Rod.
Front Axle Bolt
Welded Nut
Le Tie Rod Right Tie Rod
Tie Rod Bolt
Washer
Washer
Washers (2)
Locking Nut

Step 3: Install Steering Column
Raise the steering column up by pushing the clamp lever to the le allowing the
column to raise all the way up (Le Photo). Raise the clamp lever
upward in to the “U” slot and ghten by turning it clockwise (Right Photo).
Finally, push clamp lever down rmly to secure the steering column. Reverse
these steps when needing to lower steering column for transport.
Spring loaded pin. Push to
the le to release.
Lever is placed into the “U” slot and
clamped down. Steering column is
now secure.

Step 4: Handle Bar Assembly
Please make sure the brake line is not twisted and the brake handle is facing
forward. Insert the handle bar into the steering column (Le Photo). Raise the
handle bar to a comfortable posion and insert the height adjustment knob
into the hole and ghten (Right Photo). We recommend the handle bar height
to be set approximately waist high.

Step 5: Assemble and Install Oset Knee Plaorm
The knee plaorm is designed to be used with the right or le leg. It is very
important that the knee plaorm is set up for the proper leg as this oset is
designed to help the rear wheels stay free from the pushing leg during use. If
the le knee will be placed on the kneepad, posion the kneepad post where
the LEFT scker on the post plate is showing next to the LEFT scker on the
kneepad frame (Le Photo). If the right knee will be placed on the kneepad,
posion the kneepad post where the RIGHT scker on the post plate is showing
next to the RIGHT scker on the kneepad frame (Right Photo). Once set up
properly, insert kneepad screws and ghten.
Le knee setup Right knee setup

Step 6: Install the Fusion Cover
Starng with the right side cover, place the cover over the rear axle (Top Le
Photo) and feed the brake cable into the rear of the cover. Place the front of
brake cable between the steering column and the steering bracket (Top Right
Photo). Place the le side cover over the rear axle and feed the brake cable
into the rear slot of cover. Make sure the mounng brackets on the
underside of the scooter are inside of the cover and snap the cover together
(Boom Le Photo). Turn the unit on it’s side and install the allen bolts and
washers onto the mounng brackets to secure cover (Boom Right Photo).
Tighten the bolts, but do not over ghten.
Place brake cable through
slot.
Make sure the brake cable
is between the steering col-
umn and steering bracket.
Snap the cover together at
all tab points.
Install allen bolts with
washers into the mounng.
*Cover are availbe in dierent colors.

Brake and Parking Brake Operaon
Your KneeRover® knee walker comes equipped with a brake lock/parking brake.
To engage the brake, squeeze the brake lever on the handle bar. To apply the
parking brake, squeeze brake handle rmly and while holding the brake handle
press the silver buon to engage the lock. While sll holding the buon down,
release the brake handle and your parking brake will be set. To release the lock,
squeeze the brake handle again and the silver buon will pop up.
If needed, the brake can be adjusted in order to make ghter or looser. Please
visit hps://kneerover.com/pages/kneerover-maintenance-videos and view the
brake adjustment video.
Unlocked Parking
Brake
Locked Parking
Brake

WARRANTY
Who is Covered? This warranty applies to the original owner. To validate your
warranty, the KneeRover® scooter must be registered within 30 days of the
purchase date and have a valid proof of purchase. Please make sure to visit
hps://kneerover.com/apps/product-registraon to complete the product
registraon.
What is Covered? While the frame is covered for the life of the KneeRover®,
some parts of the scooter are subject to normal wear and tear and depending
on the use, may not last the lifeme of the scooter. The applicable warranty
coverage for all parts are listed below.
Frame, Cross Braces and Welds: LIFETIME
Brake Components and Hardware: 1 YEAR
Wheels, Kneepad, Seat and Grips: 6 MONTHS
What is NOT Covered? This warranty does not cover defects or malfuncon
caused by misuse, abuse, negligence, improper maintenance, or failure to fol-
low the user manual instrucons and safety instrucons. This warranty will not
apply to damage caused by unauthorized parts, alteraons or modicaons of
this product. Cosmec or incidental damages are not covered.
How to obtain Warranty Service: To obtain warranty service for products,
please submit a warranty claim at hps://kneerover.com/pages/warranty
and have your serial number and proof of purchase available.
If the part that you need is no longer covered under your warranty, please visit
hps://kneerover.com/collecons/parts as we carry replacement parts for all
KneeRover® models.
If you have any quesons regarding your KneeRover® product or this warranty,
please contact our Customer Care Team by calling 1-877-737-9877 or by email
at [e-mail]. We are available Monday - Friday from 9:00 am to
4:30 pm Eastern.

KneeRover® Knee Walker Safety Instrucons:
The following safety instrucons and warnings are provided to
educate the user on how to safely operate a knee walker. Knee
Walkers are mobility devices designed to provide increased
mobility during recover from foot/ankle/lower leg surgery or
injury. This is a walking aid, not a recreaonal device. For the
user’s safety, it is important to follow these safety instrucons at
all mes.
Dealer: User manual and safety instrucons must be given to the
user.
User: BEFORE using the knee walker, you must read the user man-
ual and safety instrucons and save for future reference.
Cauon: DO NOT aempt to adjust or operate
the knee walker without carefully reading all secons
of the user manual and following safety instrucons.
If you do not understand the User Manual or the Warnings and
Cauons provided here, please contact us or your healthcare
professional for a complete explanaon before aempng to
assemble or operate this equipment. Failure to read and comply
may result in injury to user or damage to the unit. If you have any
quesons, please contact us at 1-877-737-9877 or at
[e-mail].
(Customer Service Hours: M-F 9AM to 5PM Eastern)

WARNINGS:
BEFORE OPERATING KNEE WALKER:
DO NOT exceed the maximum weight capacity of 300 pounds for
this knee walker. Exceeding the maximum weight capacity may
result in injury to the user or damage to the knee walker.
Aer fully assembling the knee walker according to this user
manual, ensure that the brakes are working correctly, meaning
they engage the rear wheel(s) when the brake handle is squeezed.
Failure to do this may result in injury to the user.
Inspect the knee walker periodically to ensure the brakes and
wheels are funconing properly. Be sure steering column clamp
and height adjustment knob are ghtened and fully engaged be-
fore each use. Also, ensure that the knee plaorm height adjust-
ment clamp is ghtened and fully engaged and the locking pin is
locked in place prior to use. For All Terrain models - ensure res
are inated to the proper psi.
Only use accessories and replacement parts authorized by the
KneeRover® brand. Accessories designed by other manufacturers
have not been tested by KneeRover® and are not recommended
for use with KneeRover® products.
As a reminder, this is a mobility / walking aid, not a recreaonal
device. For the user’s safety, it is important to follow these safety
instrucons at all mes.

SAFETY INSTRUCTIONS FOR OPERATING KNEE WALKER:
As with any new physical acvity, pracce and common sense are
necessary for successful use of the knee walker. Before operang
the knee walker at normal walking speed, pracce maneuvering
and making turns at slow rates of speed to get familiar with the
knee walker and how to best maintain balance. Gradually
increase the me spent using the knee walker to allow muscles to
adjust to this new acvity. A user’s learning curve for use of the
knee walker depends on the individual’s level of acvity, balance,
and ability. Consult a healthcare professional for addional
guidance on height sengs and use of the knee walker for
maximum support and comfort during recovery.
The following warnings are intended to help the user
achieve the safest operaon of the knee walker during recovery.
Failure to read and comply may result in injury to user or
damage to the unit.
DO NOT operate the knee walker faster than a comfortable
walking speed (we recommend not more than 3 miles per hour).
Running with the knee walker or riding it fast down a hill is dan-
gerous as one can easily lose control of the knee walker and
serious injury could result.
Use extra cauon when turning the knee walker. Do not turn un-
less one foot is on the ground. Do not turn at speeds over 1 mph
(very slow walking speed). Never make a sharp turn at high speed
as this could result in a fall and serious injury,
DO NOT travel over loose gravel, large cracks, or other uneven
surfaces.

DO NOT operate on inclines above 15 degrees (slight incline). Use
Extreme Cauon when operang the knee walker on any slopes,
as there is risk of losing balance. It is best to avoid slopes. Only
mount or dismount your knee walker on a level surface.
DO NOT aempt to reach for objects while the knee walker is in
moon. Ensure that you have come to a complete stop with brake
fully engaged or locked, and have established good balance
before reaching for an object.
Be aware of your surroundings when operang the Knee Walker.
Stop and move forward slowly when encountering cracks or
separaons in walkway surfaces. Look for hazards on the ground
and avoid them to prevent falls. Use cauon when moving from
one surface to another, such as hard oors or carpet.
DO NOT use the knee walker on or near stairs, curbs, obstacles,
ect. Doing this increases risk of fall and/or injury.
DO NOT walk backwards while using the knee walker.
All wheels must be in contact with the oor at all mes while
moving on the knee walker to ensure proper balance. Always
keep both hands on the handlebar grips when in use.

Your Sasfacon is Our Top Priority:
Thank you for your business - we appreciate having you as a
customer! We are commied to providing innovave and aord-
able mobility soluons to get you moving as soon as possible aer
injury or surgery and for the duraon of your recovery - free to go
about your busy, acve life - and have a lile fun doing it.
We hope that you are completely sased with your purchase!
If you have any issues, please contact us and we will do every-
thing possible to help you. Reviews have a signicant impact on
our small business and if you purchased this product on Amazon
or eBay, we would greatly appreciate a review once you’ve had
a chance to use your new KneeRover® scooter. We hope we’ve
earned a 4 or 5 star review - if not, please give us the opportunity
to help you before leaving a review. Thank you for your support.
We appreciate you!
Need Help - Contact us:
Phone: [phone]
Email: [e-mail]
Web: www.kneerover.com
Assembly Support: hps://kneerover.com/pages/assembly-video
EU Authorized Representave
Emergo Europe
Prinsessegracht 20
2514 AP The Hague
The Netherlands
T: [phone]
EmergoEur[email protected]
KneeRover® is a registered trademark of Rover Mobility, LLC.