Knightsbridge IP9000R Instruction Manual

Remote control switch sockets
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk PS-02-2014-V1 89
INSTALLATION & MAINTENANCE MANUAL
IP9000R

IP
66
230V
50Hz
3UHVV´21µEXWWRQÀJXUH%RQWKHUHPRWHFRQWUROKDQGVHWDQGWKHUHG/('ZLOOWXUQ
RII6RFNHWLVQRZVHWWRRSHUDWHZLWKEXWWRQ
6RFNHWZLOODXWRPDWLFDOO\VHWXSDIWHUVRFNHW
6HWXSLVQRZFRPSOHWH:LWKWKHVZLWFKHVLQWKH´$872µSRVLWLRQWKHVRFNHWZLOORSHUDWH
XVLQJWKH´21µDQG´2))µEXWWRQVRQWKHKDQGVHW
NOTE%XWWRQRQWKHKDQGVHWFDQRQO\RSHUDWHWKHOHIWVRFNHWVRFNHWDQG%XWWRQ
ZLOORQO\RSHUDWHWKHULJKWVRFNHWVRFNHW
7RGHOHWHWKHPHPRU\SUHVVWKH´5(6(7µEXWWRQIRUVHFRQGVXQWLOWKHUHG/('ÁLFNHUV
DQGWKHQUHOHDVH´5(6(7µEXWWRQ7KHVRFNHWZLOOQRZQRWZRUNZLWKWKHKDQGVHW
Figure A Figure B

Red or brown
Black or blue
Green/yellow
sleeving
• Carefully push out any cable entry knockout plugs as required
• Fit cable glands (not provided) to the knockout holes as required. Ensure they are fitted
in accordance with their instructions to ensure the IP rating is maintained
• Using the back box as a template, mark the 2 fixing holes and fix the back box to a
fixed level location (e.g. wall), ensuring suitable wall fixings are used. Refit the screw
mounting hole caps (failure to fit these caps will compromise the IP rating)
• Pass the mains cable through the entry holes/glands and connect as per the
diagram opposite
• Should an earth loop connection be required, use the earth terminal block in the back
box. All earth connections must be made and maintained. Use green/yellow sleeving on
earth conductors that are not insulated
• Ensure the gasket is fitted to the inside of the lid and fix the lid to the back box using the
screws provided. The screws must be fully tightened to prevent the ingress of moisture.
Check to ensure all knockout plugs are in place and tightly pushed in. Failure to do this
correctly could compromise the IP rating
• When installation is correctly completed, re-connect mains supply and again check
all knockout plugs are in place and tightly pushed in. Failure to do this correctly could
compromise the IP rating
These instructions should be read carefully and retained after installation for further
reference and maintenance.
• Before installation/maintenance, ensure that the mains supply is switched off and the
circuit fuses are removed or circuit breakers switched off
• This product must be installed in accordance with the latest edition of the IEE
Wiring Regulations and current Building Regulations. If in any doubt, consult a
qualified electrician
• This product is IP66 rated and suitable for external applications. (Weatherproof rating
may be compromised if drain hole is opened)
• This product is class I rated and must be earthed
• 230V 50Hz voltage 13A
• Do not overload this accessory or subject it to conditions outside its weatherproof rating
• Remote control batteries – 1 x 23A/MN21 12V (not supplied)
• Remote control range <20M
• Please recycle this unit
GENERAL INSTRUCTIONS:
INSTRUCTIONS
SAFETY
INSTALLATION
• There are 2 sockets, socket 1 and socket 2 (figure A on back page)
• On the front plate, there are 2 sets of remote control mode switches
• With the switch in the “OFF” position, the appropriate socket is turned off and will have
no power output and will not work with the remote
• With the switch in the “ON” position, the appropriate socket is on, and will not work with
the remote
• With the switch in “AUTO” position the appropriate socket will work with the remote
control once it has been set up (see below)
7RVHWVRFNHW
0RYHWKHOHIWVZLWFKWRWKH´$872µSRVLWLRQVHHÀJXUH$RQEDFNSDJH)
3UHVVWKH´5(6(7µEXWWRQIRUVHFRQGVXQWLOWKHUHG/('FRPHVRQWKHQUHOHDVH
SETTING UP THE REMOTE CONTROL
Circuit
cable
Circuit
cable