Koala STUNNER SOFA User manual

August 2022
STUNNER SOFA
Clickthe button
to watch the
assembly video

x8
104-9173
x2
x2
x1
x1
x1
x1
x1 x1
x4
104-9173
x1
104-9238
x4
104-9172
What’s in the box*:
x2
x2
*Not to scale
x2
x2

1.
2.
1
Assemble the metal frame by connecting the four corners together.
Make sure brackets are facing outwards and metal ledges are
facing inwards.
Metal ledge
Bracket
Ensure the metal frames should be flush with each other before moving
to the next step.
2

3.
x4
x4
2
Lock the metal frame together by inserting 4 x gumnuts
into the corners as shown, and tighten completely.
4. Screw the plastic legs into the frame.
11

5.
6.
Flip the frame over onto the legs and insert the middle beam.
1
2
Note the dierence between the backrest and the armrests: The backrest
brackets are further apart than the armrest brackets, and the backrest is wider.

7.
8.
1
Insert the armrests and backrests by aligning the brackets
and pushing all the way down.
2
1
2
Insert the large gumnuts through the metal frame into the armrests
and backrests and tighten fully.
x4

x2
9.
10.
Place the seat base boards onto the metal ledges on the metal frame.
Hook the latch over the clasp and pull back on the handle to tighten.
This will squeeze the storage boxes together. Repeat for front and back.
Note: The latch can be adjusted
to get the proper tension
by twisting as shown here.
1
2

11.
12.
Open the storage boxes, then align the front panel with the hole
locations and use large gumnuts to secure the front panel to the
storage boxes. Tighten fully.
Lift the front of the storage box and slide the back end underneath the
front metal bar of the seat frame.
1
2
x4

13.
14.
Place the seat cushion, back cushions, and armrest cushions onto the frame.
Note the split in the seat cushion should be facing the backrest.
Note: The metal brackets at each end should be hooked under and
inside of the front metal beam as shown.

15. How to convert to sleeping position:
Remove backrest and armrest cushions
16. Pull out storage box until brackets are locked

17. Flip out the seat cushion so that it is completely flat
18. Take a nap.

Product Information and Care
FABRIC
Regular Care (Weekly)
• Vacuum regularly using low suction
• Protect from direct sunlight
• After use, you can floof the cushions to bring them back to shape
Cleaning
• Remove any spills immediately by gently blotting any liquid stands with a clean cloth.
Scoop any sauces up before blotting the remaining sauces
• Use a mild detergent to gently remove any loose soilage.
• Do not scrub with a sti brush.
• Use a clean cloth to blot out any excess liquid.
• Avoid over wetting as this may result in a water mark.
Caution: Pretest the cleaning method on a hidden area of the sofa. If change in colour, or transfer
do not continue.
PILLING
Pilling can occur occasionally as a result of normal daily wear and should not be considered a fault.
Fibre pills can be removed with a battery operated pilling tool, available from most haberdashery stores.
TIMBER
Regular Care (Weekly)
• Wipe down with a clean damp cloth
• Protect from direct sunlight
Cleaning
• Treat spills as soon as possible, wipe down with clean dry cloth.
• Do not use abrasive cloths, concentrated detergents, silicon based wood polishes.
Good to Know:
Timber is a natural product and there will be variation in grain, colour and features such as knots.
Over time the colour of timber will naturally change.
USING THE SOFA & DRAWERS
Weight Capacity
• Sofa Weight Capacity: 120kg per seat
• Drawer Weight Capacity: 20kg per drawer
SAFETY AND USE
• Open the drawer by pulling it open with the handle, close by pushing it from the middle.
• Drawer will work best on a smooth surface.
• Do not open lids of drawer when it is being used as a sofa bed.
• Remember they are drawers not toys.
• Do not jump or stand on the drawers.
• Avoid sitting on the arms or backrest.
• Avoid dragging the sofa if you need to move it
(remember to remove the drawers first).