Kodak Smile User manual

User Guide
KODAK SMILE
INSTANT DIGITAL PRINTER
Imprimante numérique instantanée
Stampante istantanea digitale
Sofortdigitaldrucker
Impresora digital instantánea
Guide de l'utilisateur
Guida utente
Benutzerhandbuch
Guía del usuario

4 | EN
INTRODUCTION
Thank you for purchasing the KODAK SMILE
Instant Digital Printer. This User Guide is
intended to provide you with guidelines to
ensure that operation of this product is safe
and does not pose risk to the user. Any use
that does not conform to the guidelines
described in this User Guide may void the
limited warranty.
Please read all directions before using the
product and retain this guide for reference.
This product is intended for household use
only. It is not intended for commercial use.
This product is covered by a limited one-year
warranty. Coverage is subject to limits and
exclusions. See warranty for details.
SPECIFICATIONS
• Dimensions: 4.625 L x 3.188 W x 0.938 H
(11.75 x 8.15 x 2.5 cm)
• Weight: 7.2 oz (204 g)
• Colors Available: Black/White, White/Yel-
low, Blue, Green, Red
• Battery Capacity: 700mAh
• Battery Type: Lithium-polymer
• Prints Per Charge: ~40
• Supported Photo Paper: KODAK ZINK 2 x

EN | 5
3 sticky-back photo paper
BOX CONTENTS
KODAK SMILE Instant Digital Printer
Starter Pack of KODAK ZINK Paper
User Guide
SAFETY PRECAUTIONS
• Do not attempt to disassemble this device
for any reason.
• Never leave your printer or the ZINK® paper
in an area that might become extremely
hot or where it will be exposed to direct
sunlight for a long time. This can cause
your printer to overheat or suer other
problems.
• Don’t get it wet! If you need to clean your
printer, use a soft cloth that’s been slightly
dampened with water or rubbing alcohol,
and gently wipe away any dirty spots. Don’t
submerge the whole thing in water, ever.
• Be careful with your printer. Try not to drop
it, or shake it violently. The inside of the
printer has a lot of very small parts that
could break if they are jostled around too
much.
• Do not use products such as alcohol,
gasoline, diluent, or any other organic
solvent when cleaning or attempting to
clean this product.
• Do not use this device in an environment

6 | EN
where it will be exposed to heavy dust or
humidity/moisture.
• Do not use this printer while bathing or in
a shower.
• Do not place or charge the printer where it
can fall or be pulled into a tub or sink.
• Do not place, drop, or submerge the
printer in water or any other liquid.
• If the printer somehow falls into water
despite you taking all of the above
precautions, please do not reach into
the water to retrieve it, especially if it
is charging. If it is charging, unplug it
immediately and then retrieve it.
• Take care that objects do not fall and
liquids are not spilled onto the printer.
• This printer absolutely will not work
without downloading the ANDROID
or iOS application. If you do not have
an ANDROID phone or an IPHONE,
unfortunately, this printer will not work for
you.

EN | 7
PRODUCT OVERVIEW
Micro USB
charging port
Paper slot
Charging
indicator LED
Reset button

8 | EN
Power indicator LEDs
IDLE SOLID WHITE
ERROR SOLID RED
DATA TRANSFER BLINKING BLUE
NO PAPER BLINKING RED
PRINTING BLINKING WHITE

EN | 9
GETTING READY FOR USE
Charge the SMILE
Before using the printer, connect it to the
charger by plugging the micro USB cable
into the designated micro USB charging port
on the side and allow it to fully charge.
If the red indicator LED light is lashing, this
means that the battery is low and you should
plug the printer in for it to recharge. While
the printer is charging, the indicator LED will
be a solid red light. Once the process has
completed, the indicator LED will change to
a solid green light.
Load the Paper
Load your ZINK paper into the printer: Follow
the steps below to quickly and easily get
your new printer loaded with ZINK sticky-
back paper so you can start printing photos!
1. Open the paper tray in the back by
removing the tray cover at the rear of the
device.

10 | EN
2. Load the blue calibration sheet in with
the barcode facing down. Place the other
plain sheets on top with the glossy side
facing you. Try to avoid touching the
glossy side so you don’t get ingerprints
on it.
3. When you print your irst photo after
loading the ZINK paper, the blue
calibration sheet will be slowly ejected
from the printing slot. Your photo will print
after the calibration sheet inishes.
Download the App
Download the KODAK
SMILE App from the
APPLE APP STORE or
GOOGLE PLAY. You will
need the app installed
on your phone for the
printer to work.

EN | 11
Power it On/O
1. To turn the printer on, slide the small ridged
panel away from the center. This will cause
the printing slot to pop up and the LED light
strip to illuminate.
2. To turn the printer o, simply press down
the pop-up printing slot.
PRINTING PICTURES WITH KODAK
SMILE
1. Turn the printer on by sliding the small
ridged panel away from the center.
2. Make sure BLUETOOTH on your phone is
enabled.
3. Open up the KODAK SMILE App from your
phone, follow the instructions to pair your

12 | EN
printer with the app, and start using your
new KODAK SMILE printer!
If you have trouble connecting your printer
from the application, try following these steps
instead:
1. Access your phone’s BLUETOOTH settings,
usually found under the general Settings
menu.
2. Make sure the printer is on irst, and then
allow your phone to scan for new devices.
3. You will see “KODAK SMILE XX:XX” appear
in the BLUETOOTH list. The X’s will be
replaced with speciic letters and numbers
which correspond to your speciic printer.
Tap on it to start pairing.
4. After a couple of seconds, your phone
should say “paired”.
In Case of Paper Jam
If the printer jams while attempting to print,
follow these steps to resolve the issue:
1. Use a small pin/needle/paper clip to press
the reset button on the side of the printer
next to the charging port.