Kogan KADCFAN3N1A User manual

3-IN-1 DC MOTOR
PEDESTAL FAN
KADCFAN3N1A

Ensure to read this user guide prior to first use. Retain this user guide for future reference.
•This fan can be used by children aged 8 years and above and by persons with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge if they have been given supervision or instruction concerning the use of
the fan in a safe way and understand the hazards involved.
•Adult supervision is required when the fan is operating around children.
•Do not allow children to play with the fan.
•Cleaning and maintenance shall not be performed by children without supervision.
•Do not allow the fan and remote control to be operated in or around water or any
other liquid.
•Do not submerge the fan or remote into water or any other liquid.
•Do not touch the blades when the fan is in operation.
•Always disconnect the power cord before cleaning.
•If the power cord is damaged, stop use immediately and contact help.Kogan.com for
assistance.
•Do not attempt to repair the fan yourself.
•Once the fan is assembled, do not remove the grilles.
SAFETY & WARNINGS

ABase (x1) BPole assembly (x2) CFan body (x1)
DFan blade (x1) EFront grille (x1) FRear grille (x1)
GScrew (x1) HRemote control (x1) IUser guide (x1)
COMPONENTS

Fan
Control panel Remote control
OVERVIEW
Fan blade
Front and rear grille
Control panel
Pole assembly
Base
Display
Oscillating
/timer button
Fan speed button
Power button
Fan speed
button
Oscillation
button
Power
button
Timer
button

1. Loosen and remove the lock nuts for the rear grille and fan blade from the fan body.
2.Secure the pole assemblies to the base by rotating clockwise.
ASSEMBLY
Fan blade
lock nut
Rear grille lock nut
Fan
body
Pole assemblies
Base
Fan blade
lock nut
Rear grille
lock nut

3.Attach the fan body onto the pole assembly, then attach the rear grille onto the fan
body.
4.Secure the rear grille lock nut clockwise onto the rear grille. Secure the fan blade,
then place and turn the fan blade lock nut anti-clockwise.
Rear grille
lock nut
Fan blade
lock nut
Fan body
Pole assembly
Rear grille
Rear
grille
Fan blade

5.Align the top clip of the front grille with the rear grille, then press the front and rear
grilles together.
6.Using a screwdriver (not supplied), secure the locking clip connected to the front grille
with the provided screw. This will secure the front grille in place.
Screw
Locking clip
Rear grille
Front grille

Batteries for the remote control
1. Slide the back cover off the remote control.
2.Noting the polarity markings ‘+/–’, insert two AAA batteries (not supplied) into the
remote control. Slide the back cover on.
Powering on/off
1. Plug the power cord into a socket, then turn the socket on.
2.Press the Power button on the remote control or control panel to turn on the fan.
3.Press the button again to turn off the fan.
BEFORE FIRST USE
OPERATION
Note:
To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust.

Timer
The timer can be set to either turn the fan on or off after a specified period between 0.5–12
hours.
Setting the timer to turn on the fan
There are two methods. Applicable to both methods, ensure the fan is in standby when
setting this timer.
•Using the control panel:
1. Press and hold the oscillation/timer button for two seconds.
2.Repeatedly press the oscillation/timer button to adjust how long you wish the
timer to last. This will be reflected on the display (0.5–12). Once adjusted, do not
touch the control panel. Wait for six seconds.
3.Press the fan speed button to adjust the speed at which the fan will operate when
it turns on (1–12).
4.Once adjusted, do not touch the control panel. Wait for three seconds. The display
will flash twice and beep to confirm the timer has been set.
•Using the remote control:
1. Press the timer button to enter the timer settings.
2.Repeatedly press the timer button to set the timer to the desired number of hours.
Each press will increase the timer by one hour. This will be reflected on the display.
Setting the timer to turn off the fan
There are two methods. Applicable to both methods, ensure the fan is turned on when
setting this timer.
•Using the control panel:
1. Press and hold the oscillation/timer button for two seconds.
2.Repeatedly press the oscillation/timer button to adjust how long you wish the
timer to last. This will be reflected on the display (0.5–12).
3.Once adjusted, do not touch the control panel. Wait for six seconds. The display
will flash twice and beep to confirm the timer has been set.
Notes:
•If you wish to reset the timer, press and hold the oscillation/timer button.
•Pressing the Power button will cancel the timer and turn on the fan.
Notes:
•To check how much time is left on the timer, press and hold the
oscillation/timer button. The time left will be shown on the display. If you
would like to adjust the timer, immediately press the oscillation/timer
button and adjust accordingly.
•
If nothing is pressed for six seconds, the current timer will remain set.

•Using the remote control:
1. Press the timer button to enter the timer settings.
2.Repeatedly press the timer button to set the timer to the desired number of hours.
Each press will increase the timer by one hour. This will be reflected on the display.
Oscillation
When the oscillation function is turned on, the fan will automatically rotate left and right.
Press the oscillation button on the remote control or the oscillation/timer button on the
control panel to start/stop oscillating.
Changing the fan speed
This fan features twelve fan speeds.
Press the fan speed button on the remote control or control panel to change the fan speed.
The selected fan speed will be reflected on the display (1-12).
Press and hold the fan speed button to quickly cycle through the fan speeds.
Changing the angle of the fan
The angle/tilt of the fan can be changed manually. Ensure the fan is turned off and
unplugged before adjusting accordingly.

Adjusting the height
The pole assemblies can be removed to create different heights for the fan. This results in
three different configurations.
To change the configuration:
1. Remove the fan body.
2.Rotate the pole assembly/assemblies anti-clockwise then remove.
3.Resecure the fan body onto the remaining pole assembly/base.

Ensure the fan is turned off and unplugged before cleaning.
1. Wipe the exterior with a soft cloth dampened with a mild detergent.
2.Remove any soapy residue with a dry cloth.
Disposal
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it.
CLEANING & CARE
Notes:
•Do not disassemble the fan to remove dust.
•Do not use any abrasive detergents or solvents during cleaning to avoid
scratching or damaging the surface of the fan.
•Do not use gasoline or thinner for cleaning.

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com