Kogan SHANGRI-LA SLROBINBFWA User manual

ROBIN 2 DOOR BUFFET
SLROBINBFWA & SLROBINBFBA

Please read these safety instructions thoroughly before using this product. Retain this guide
for future reference.
• Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
• Separate and identify each component from the hardware pack and rest it in its
final location before fastening.
• Do not fully tighten screws (leave slightly loose). When the item is fully assembled
tighten the screws - but do not over tighten.
• If glue is required, do not set until you are certain that the parts belong together.
SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
Parts:
COMPONENTS

No.
Size (mm)
Qty
No.
Size (mm)
Qty
1
60 x 395 x 40
1
17
387 x 659 x 2.5
1
2
60 x 395 x 40
1
18
46 x 500 x 15
1
3
60 x 395 x 40
1
19
46 x 755 x 15
1
4
60 x 395 x 40
1
20
46 x 500 x 15
1
5
394 x 585 x 15
1
21
50 x 1052 x 15
2
6
394 x 585 x 15
1
22
50 x 224 x 15
2
7
393 x 633 x 15
1
23
80 x 145 x 15
1
8
394 x 1222 x 15
1
24
80 x 145 x 15
1
9
394 x 1222 x 15
1
25
190 x 496 x 15
1
10
376 x 500 x 15
1
26
190 x 496 x 15
6
11
360 x 754 x 15
1
27
130 x 350 x 12
2
12
374 x 610 x 15
1
28
130 x 350 x 12
2
13
374 x 610 x 15
1
29
128 x 456 x 12
2
14
259 x 659 x 2.5
1
30
344 x 465 x 2.5
2
15
259 x 659 x 2.5
1
31
50 x 335 x 12
2
16
387 x 659 x 2.5
1

Hardware:
AØ15x9.6 (x46)
B35mm (x44)
CØ4x25 (x12)
DØ4x32 (x4)
E14" (x4)
F14" (x4)
GØ3.5x12 (x24)
H(x40)
IØ5.5x38 (x7)
JLegs (x4)
KØ5x16x1
L
MØ5x16 (x6)
NØ632 (x2)
O68mm (x3)
PØ35 (x4)
QØ4x15 (x16)
R(x4)
SØ3.4x10 (x4)
TØ20 (x14)

IMPORTANT! Read before assembling
This product contains multiple sets of metal slide runners and slide tracks (shown separated
above).
To a v o i d damage to these items during transportation, the slide runners and tracks have
been pre-assembled together in pairs. Each pair includes one slide runner and one slide
track.
Before assembling your furniture, separate the runners from the tracks according to the
following instructions:
• Extend the slide runners.
• Gently press the plastic release lever on the slide runner while pulling the slide
runner and slide track apart from each other.
• The slide runner and slide track should now be separated. Repeat these steps for
the remaining pairs of slide tracks:
ASSEMBLY
Slide runner
Slide track

Step 1:
B35mm (x8)

Step 2:
F14" (x4)
GØ3.5x12 (x12)
x2 Drawer Slides F
x2 Drawer Slides F

Step 3:
AØ15x9.6 (x2)
DØ4x32 (x4)
Arrow points in
the direction of
end hole