Kogan Ovela Santee OVSANTEEWDA User manual

SANTEE METAL
WARDROBE
OVSANTEEWDA

ALarge Shelf (x4)
BSmall Shelf (x3)
CSupport Rail (x2)
DLower Pole (x8)
EMiddle Pole (x8) FUpper Pole (x8)
G Long Clothes
Hanger Rod (x3)
HHook Bracket
(x8)
IScrew (x8)
JShort Clothes
Hanger Rod (x1) KPlastic clip (x64)
LLeveling Feet
(x8)
COMPONENTS

OVERVIEW

Step 1:
Screw the x8 Leveling Feet (L) into the bottom of the Lower Poles (D).
Snap the Plastic Clips (K) into the pole grooves of the Lower Poles, each at the same
position, and ensuring that the arrow on each plastic clip is pointed up.
Arrow points up
ASSEMBLY

Step 2:
Take Large Shelf (A) and ensure it is positioned the correct way up, as per the image below.
Hold the shelf on its side and slide the top of 4 pieces lower poles through the bottom of the
shelf at its corners until there is snug fit.
After 4 poles have been slid through the shelf collar holes, set the shelf upright.
Up
Collar
Down

Step 3
Repeat step 2 again to create the other base assembly, ensuring the height for the shelving
is identical between the two.
Step 4
Snap plastic clips onto the same grooves of the centre four lower poles at your desired
height for the first Small Shelf (B). Slide the small shelf from the top of these centre four lower
poles down onto the plastic clips. Refer to the image below for reference.

Step 5
The Middle Poles (E) are fitted with screw connectors (shown in the image below). Use these
connectors to attach the middle poles to the lower poles.
Repeat the same method to attach the Upper Poles (F) to the middle poles (E).

Step 6
Snap the plastic clips (as per step 4) to snap plastic clips at the same height grooves of the
centre four poles and install the second small shelf in the middle of the rack.
To attach the Support Rails (F), fit another x4 plastic clips on the poles making up the right-
hand side frame assembly (see image below for reference), then slide the support rails down
from the tops of the poles, onto the plastic clips.
Next, snap the plastic clips at the same height grooves of the centre four poles and install
the third small shelf in the middle of the rack. Fit plastic clips at the top of upper poles and
place the remaining two Large Shelves (A) into position on top, pushing firmly down on every
shelf at corners.

Step 7
Connect the Long Clothes Hanger Rod (G) with the two assembled support rails via Hook
Bracket (H) and Screw (I) as per the below image.
Hang the remaining two long clothes hanger rods respectively onto the two top large
shelves at their frames by hook bracket and screw.
Similarly, hang the Short Clothes Hanger Rod (J) directly onto the second layer of small
shelves at its frame as per the below image.

Step 8
Use a rubber mallet to ensure the shelf is firmly in place over the plastic clips. To ensure
stability, adjust the levelling feet on each of the 8 lower poles, ensuring the wardrobe can
stand straight upright with no imbalance.
High
Low

Step 9
Fasten the wardrobe to the wall with the anti-toppling kit included in the package.
TOPPLING FURNITURE WARNING:
•It is strongly recommended that this product is permanently fixed to the wall.
•Please seek professional advice if you are in doubt of what fixing device to use.
•Regularly check that anchors are securely maintained.
•Stability of tall items may be affected by thick carpets or uneven floors.
•Do not place unanchored televisions on furniture.
Caution!
For your safety when attaching the anchor fixings, please note the following:
Check any electrical wires or plumbing inside the wall before drilling any holes (if you
are unsure please seek professional advice from a qualified tradesperson).

MAnti-Tip Device
(2Sets)
Assembly complete

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com.