Kogan SMARTERHOM LX12 User manual

KOGAN SMARTERHOME™ LX12
ROBOT VACUUM CLEANER DOCK
KAVACRBL12D

Caution
•This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
•Please use this product only as instructed by this user guide.
Warning
•This product is not a toy. Please keep children and pets away from this product
during use.
•Please avoid sitting or standing on this unit.
•This product comes with a power cable approved regionally, which can only be
used with standard domestic AC outlets. Please do not use any other power
cables. In case of need to replace the power cable, cease use immediately and
contact help.kogan.com before further use.
•Please do not disassemble this product unless. No spare parts are available inside
the unit. If disassembly is necessary, cease use immediately and contact
help.kogan.com before further use.
•Please use this product in dry indoor environment only to avoid electric shock.
•Please do not use this product with wet hand.
•Please store or use this product at room temperature.
•Please unplug this unit before cleaning to reduce the risk of electric shock.
•Please do not load this unit with any liquids or soak it in water.
•Please do not use this unit outdoors or in wet environment.
•Please do not use this unit when its cable or plug is damaged. In case of any
operational failure, cease use immediately and contact help.kogan.com before
further use.
SAFETY & WARNINGS

Dock x1
Front
Back
OVERVIEW
Cover
Dust bin
Charge / Dust collection
indicator light
IR lens
Suction inlet
Charging contact pins
Air Outlet

Uncovered
Beneath view
Seal ring for cover
Fan filter support
Transparent cover for
dust passage

Other Parts
Dust Bags
Note:
A new dust bag has already installed in the dust bin of the dock.
Handle of dust bag
Dust bag
Please remove the dust bag
coming with the unit from here

1. Please install this unit on a flat ground, ≥ 6cm away from the side wall.
2. Please keep open the space ≥ 1.2m ahead and ≥ 0.5m on both sides of the unit.
The dock covers both dust collection/disposal and vacuum charging functions, and comes
pre-installed with a new dust bag.
After cleaning, the robot vacuum will automatically return to the dock. If the robot is not
installed with the water tank, the dock will empty its dust box and then charge it. If the robot
is installed with the water tank, it will be charged directly. When the robot is at the dock,
please remove the water tank, the dock will empty the dust box and then charge the robot.
INSTALLATION
6cm away from the side wall

Replacement of dust bag:
The quick-flashing orange indicator on the unit denotes full dust bag or you may change the
dust bag as required by the mobile app. It is recommended to replace the dust bag once
every 6-8 weeks.
Open cover
Remove the dust
bag by pulling up
its handle
Discard the
removed dust bag Replace with a new one Restore the cover
Dust passage cleaning
In case the orange indicator flashes quickly when the dust bag is not full, please unplug and
reverse the unit to check if there is block-up inside the transparent cover; if so, please remove
the screw with a screw driver as indicated on the right image. Then open the transparent
cover to the dust passage and remove any blockage.
Please remove the screw with a screwdriver and avoid removing it violently Restore the
transparent cover as it was after cleaning.
CLEANING & CARE
Transparent cover for
dust passage

IR lens and charge/dust collection shrapnel cleaning
Check if IR lens and charge/dust collection shrapnel are contaminated. If so, remove any dirt
with a clean and dry cloth and make sure they are fully cleaned away. Cleaning once every
month is recommended.
Fan filter support cleaning
Check if the fan filter support is contaminated by lint or debris. If so, remove them with a
clean and dry cloth. Cleaning once every month is recommended.
Fan Filter Support
IR lens
Charging Contact Pins

Dimensions
255 x 225 x 340mm
Rated power
1050 W
Rated input
220-240V ~ 50/60Hz
Rated output
DC24V 1.2A
The status of this product is shown by the LED indicator on the front of the unit and the app:
LED
indicator
Common
problem Solution
Quick-flash
orange
indicator
Missing dust
bag, fan not
started or
other failures
Check if the dust bag is missing and if so, please install one.
Check if the dust bag is properly installed.
Frequent dust collections trigger over-heat protection or
malfunction of the fan. It is recommended to wait for 30
minutes before start to collect dust again.
Full dust bag
or block-up
Replace with a new dust bag.
Make sure the cover of the unit is fully closed and sealed. If
the robot vacuum cleaner is charging on the unit, you may
try to start the unit to collect dust. Here is how to initiate the
dust collection manually: Press Clean/Power button on the
robot vacuum cleaner to start the cleaner. Then press any
button on the cleaner to pause the machine after it leaves
the dirt disposal. Press Recharge on the cleaner to make it
return to the unit to collect dust. Recharge auto starts after
dust collection is finished.
Remove dirt from the suction inlet at the bottom of the
cleaner and from the dirt disposal.
Unplug the dirt disposal. Reverse the unit to check if there is
block-up inside the transparent cover; if so, please remove
the screw with a screwdriver. Then open the transparent
cover to the dust passage and remove any blockage.
SPECIFICATIONS
TROUBLESHOOTING