Kohler 23472T-4 User manual

1331663-2A-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. If possible, install this faucet before installing the lavatory.
3. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
4. Observe local plumbing codes.
5. Shut off the water supplies to the fitting.
1331663-2A-A 4
INSTALLATION INSTRUCTIONS
23472T-4 Single Handle Lavatory Faucet
23475T-4 Tall Single Handle Lavatory Faucet
23478T-4 Super Tall Single Handle Lavatory Faucet
PARALLELPARALLEL
SERVICE PARTS
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, turn counter-clockwise for cold water.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
ROUGH-IN DIMENSIONS
23472T-4 Single Handle Lavatory Faucet
23475T-4 Tall Single Handle Lavatory Faucet
23478T-4 Super Tall Single Handle Lavatory Faucet
1331657**
1331656**
1331655
1343774
3012353
1310075
1343771
3008523
833438
1343773
1239175
1231664
1231664
1231664
834704
3006148
1331372**
1080817
1331371**
1132027**
880406
1132031
1132022
1132034
1331357
1030925
1132033
1331351
1331661**
1146748
1228834
1331350**
23478T-4
47
G1/2˝
45 Max.
Ø32~Ø38
Ø50
269
321
155
136
15.2º
60 MIN
381
23475T-4
Ø32~Ø38
209
261
Ø50
45 Max.
155
60 MIN
15.2º
136
47
G1/2˝
441

1331663-2A-A 2 1331663-2A-A 3
INSTALLATION
How to Install the Spout
Install the mounting studs(3) onto the faucet body base(1), and put the
washer(2) into the groove at the bottom of the faucet over the flexible
hoses(4) and cable end(5).
Insert the faucet assembly into the lavatory hole. Position the faucet
properly. From underside of the lavatory, place the brackets(6, Rubber
washer is on the top) onto the mounting stud, and tighten the nuts(8) with
a wrench(7) to secure the faucet.
Attach the hoses to water supplies. When facing front of the faucet, the
left hose connects to hot water, the right hose with "COLD" label
connects to cold water.
How to Install the Drain
Remove stopper(9), flange(10) and washer(11) from drain body(13).
Insert drain body through the drain hole from underside, and adjust the
position properly. Screw the flange(10) with washer(11) onto the drain
body.
Tighten the locknut(12) on the drain body by wrench. Insert the
stopper(9) into the drain assembly(13).
NOTE: If needed, apply a ring of plumbers putty around the underside of
the drain flange, instead of using washer(11).
Open the coverplate(14) on the drain body, and insert cable end(15) into
the square hole (17) of cable box(16). Make sure the cable is properly
buckled at both ends(A, B) of the cable box as the figure shown.
Lock the coverplate(14), and verify the lift rod (18) on the faucet is linked
correctly with the drain body through the cable.
NOTE: Do not reposition the drain if plumbers putty applied after the
locknut is tightened, or you may break the putty seal. Wipe away excess
plumbers putty.
INSTALLATION CHECKOUT
Ensure that all connections are tight. Ensure that the handle is in the off
position. Turn on the drain and main water supply, and check for leaks.
Repair as needed.
Remove the aerator kit(20) by tool(19). Turn on the faucet. Run hot and
cold water through the faucet for about one minute to remove any debris.
Remove any debris from the aerator kit. Shut off the faucet. Reinstall the
aerator kit.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
9
10
11
13
12
20
19
14
15
16
17
A
B
23472T-4 23472T-4 & 23475T-4 & 23478T-4
18
Ø31.75
56
95.7 114
Ø32
Ø36.5
G1/2˝
47
45 Max.
Ø32~Ø38
Ø50
156
104
115
133
15.2º
60 MIN
546
7
1
2
3
5
4
6
8