Kohler ANTIQUE Series User manual



116585-2-BA (-) 1999 Kohler Co.
BEFORE YOU BEGIN
NOTES
This faucet is for use on a single-hole lavatory.
For three-hole lavatories, use the optional
escutcheon plate.
For proper lift rod operability, allow a 2-3/4”
clearance between the faucet center and the
wall or lavatory.
2-3/4” Minimum
Clearance
Shut off the main water supply.
Observe local plumbing codes.
If possible, install this faucet before
installing the lavatory.
Inspect the supply tubing for damage.
Replace as necessary.
Kohler Co. reserves the right to make
revisions in the design of faucets
without notice, as specified in the Price
Book.
TOOLS AND MATERIALS RECOMMENDED
Adjustable wrench
Thread sealant
Plumbers putty
Hacksaw or tubing cutter
Shut-off valves
INSTALLATION
FOR THREE-HOLE LAVATORIES
Installation to marble or plastic: Do not use
plumbers putty. Remove the adhesive backing
from the gaskets, and firmly press them over the
two outside lavatory holes. Position the spacer
over the center lavatory hole so the gasket
surface is down. Position the escutcheon over
the three lavatory holes.
Installation to any other materials: Apply a
ring of plumbers putty or other sealant to the
bottom edges of the escutcheon according to the
putty manufacturer’s instructions. Position the
spacer over the center lavatory hole so the
gasket surface is down. Position the escutcheon
over the three lavatory holes.
Escutcheon
Apply
Plumbers
Putty
Spacer
Gasket
ANTIQUE
SINGLE-CONTROL
LAVATORY FAUCETS

INSTALLATION
INSTRUCTIONS

116585-2-BA (-) 2Kohler Co., Kohler WI
ALL LAVATORIES
Thread the mounting stud into the bottom of the
faucet body.
Installations with escutcheon: Fit the faucet in
the lavatory hole. Insert the lift rod into the faucet
body.
Installations without escutcheon: Apply
plumbers putty or other sealant around the
underside of the round base according to the
putty manufacturer’s instructions. Fit the round
base onto the faucet. Fit the faucet and round
base in the lavatory hole. Insert the lift rod into
the faucet body.
Escutcheon
Lift Rod Faucet
Body
Mounting
Stud
Round Base (Do
Not Use With
Escutcheon)
Apply Plumbers
Putty
All installations: Install the bracket and spacer
to the mounting stud, and thread the nut in
place. Position the faucet, and securely tighten
the nut.
Remove any excess putty or sealant from the
escutcheon or round base. Bracket Spacer
Nut
Mounting
Stud
DETERMINE YOUR DRAIN STYLE AND FOLLOW THE APPROPRIATE INSTALLATION
STEPS.
DRAIN (CP AND PB FINISHES)
Remove the protective seal from the flange.
Apply a 1/2” diameter ring of plumbers putty or
other sealant around the underside of the flange
according to the putty manufacturer’s
instructions. Insert the flange into the lavatory
drain hole.
Assemble the gasket (tapered side up) and
washer to the flange, and partially thread the nut
to the flange. Do not fully tighten the nut at this
time.
Install the body washer and body to the flange,
and wrench tighten.
Position the body so the seal hole is facing
toward the back of the lavatory.
Handtighten the nut.
Remove any excess putty or sealant.
Flange
Apply Plumbers Putty
Gasket
Washer
Nut
Body Washer
Seal Hole
Body

3116585-2-BA (-)
Kohler Co., Kohler WI
DRAIN (OTHER FINISHES)
Remove the flange from the body.
Thread the nut completely onto the body.
Apply a 1/2” diameter ring of plumbers putty or
other sealant to the underside of the drain flange
according to the putty manufacturer’s
instructions.
Insert the drain body up into the underside of the
lavatory drain hole.
Position the body so the seal hole is facing
toward the back of the lavatory.
Thread the flange onto the drain body from the
topside of the lavatory.
Securely handtighten the nut from the underside
of the lavatory.
Remove any excess putty or sealant.
Seal
Hole
Apply Plumbers
Putty
Body
Nut
Lavatory
Underside
Flange
Assemble the nylon washer, metal washer, and
nut onto the long end of the rod.
Assemble the nylon washer and rubber washer
onto the short end of the rod. Rod
Nut
Nylon Washer
Nylon Washer
Metal Washer
Rubber Washer
ALL DRAINS
Insert the stopper into the flange.
Remove the body nut from the seal hole.
Fit the short end of the rod into the body seal
hole and under the stopper for regular
installations; through the hole for
vandal-resistant installations.
Loosely secure in place with the body nut.
Remove and adjust the stopper so the stopper
lifts about 3/8” when opened. To adjust, loosen
the stopper nut and shorten or lengthen the
stopper as needed. Re-tighten the stopper nut.
Handtighten the body nut.
Apply thread sealant to the tailpiece. Thread the
tailpiece into the body and securely handtighten.
Stopper
Rod
Seal Hole
Body
Nut
Apply Thread
Sealant
Tailpiece
Stopper
Nut
Body

116585-2-BA (-) 4Kohler Co., Kohler WI
Assemble the connecting link to the rod with the
clip.
Insert the lift rod through the faucet escutcheon
from the underside, and thread the lift rod knob
to the lift rod.
Slide the faucet lift rod through the hole in the
link.
Wrench tighten the screw on the link so the lift
rod knob is 1/2” above the lift rod hole.
Thumb Screw Link
Clip Rod
IF THE LAVATORY IS NOT INSTALLED, INSTALL IT AT THIS TIME. BE SURE TO
FOLLOW ALL INSTRUCTIONS PACKED WITH THE LAVATORY.
SUPPLIES AND STOPS
Connect the supply tubes to the faucet inlets and
supply stops (Left is hot – right is cold.)
Wrench tighten all connections.
Supply Tube
Supply Tube
INSTALLATION CHECKOUT
Connect the tailpiece and P-trap.
Ensure that all connections are tight.
Remove the aerator.
Open the drain.
Turn on the main water supply and check for
leaks.
Open the valve and run water through the spout
to remove any debris. Turn the valve off.
Reinstall the aerator.
Spout
Aerator
CALL US FOR HELP – 1-800-4-KOHLER
REQUESTING SERVICE
Here’s what you need to do if you require service:
First review the installation instructions to ensure correct installation. If you are still unable to correct
the problem, call our Customer Service Department for direct help. Dial 1-800-4-KOHLER.