Kohler AVID 97367T-4 User manual

1248999-2A-C 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
5. Check for leaks before covering the pipes, repairs as needed.
6. The highest working pressure for handshpwer is 0.5MPa(5 bar). If it exceeds 0.5MPa(5 bar), a pressure
reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower and
shower arm away from heater, or it may become damaged and cause injury to the user.
7. Please purchase the matched mounting base 97904T when install the faucet.
INSTALLATION INSTRUCTIONS
97367T-4 Floor Mount Bath Filler With Handshower97367T-4 Floor Mount Bath Filler With Handshower
AVID
ROUGH-IN DIMENSIONS
*Please purchase the appropriate bathtub according to the dimension.
Handshower
Hose
G1/2˝
G1/2˝
1500
678~698
915~935
G1/2˝
3º
*226
50
255
*70 Min.
780~810
860~880
630 Max.
Ø120
Bathtub
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
G1/2″
24 28
220
9
97367T-4
1248999-2A-C 4
AVID
SERVICE PARTS
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
3008316
871128
1224838
1177225
34263
1174121
1084120
836547
3006148
1258088
1243755**
1226889
1082901
65218
1174014
1302003**
1302004**
3008519
CP: 1227389**
TT: 1287813**
3013706
831752
880010
831727**
880010
1199166**
79680
1249005
1242418
1229992
1244431**
1344635**
38618

1248999-2A-C 2 1248999-2A-C 3
INSTALLATION CHECKOUT
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
INSTALLATION
How to Install the Faucet
Shut off water supply. Cut away the
extending part of the base protector(1)
in accordance with the tile surface.
Remove plug(2) from the base.
Remove protector(3) from the faucet.
Slide up escutcheon kit(4). Install the
faucet. NOTE: Keep the faucet vertical
to base, to avoid damaging the O-rings
on the bottom.
Keep the spout pointing to tub. Fix the
faucet to the base with screws(5) and
washers(6) through flange(7). Tighten
the screws with hex wrench(8).
Slide down the escutcheon kit, make
sure it against the finished wall.
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off
position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Remove the aerator(14) by key(13).
Remove the handshower(11). Turn on
faucet handle. Run hot and cold water
through spout for about one minute to
remove any debris. Check for leaks at
this time. Remove any debris. Shut off
the faucet. Reinstall the aerator and
handshower.
How to Install the Handshower
Remove the protector from diverter
kit(9).
Connect hose(10) to diverter kit and
handshower(11) with washers. Tighten
all the connections.
Hang the handshower on the
bracket(12) of the faucet.
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
Lift and turn the diverter for handshower. Turn the diverter in the normal position for bath spout.
14
13
11
8
10
11 12
9
2
1
3
7
5
6
4