Kohler ESCALE Operation manual

1102602-A2-H
Installation & User Guide
Dual-Flush Toilet
OPIAZ
ESCALE
PERSUADE REACH
PANACHE
OVE
MIRAGE
PARLIAMENT

1102602-A2-H 2 Kohler Co.
Thank You For Choosing Kohler Company
Before You Begin
Tools and Materials
CAUTION: Risk of personal injury or product damage. Handle
with care. Vitreous china can break or chip if the product is handled
carelessly.
Observe all local plumbing and building codes.
Carefully inspect the new toilet for damage.
 Ifthe existingtoilet doesnot haveasupplyshut-ovalvebelowthe
cistern, install one before installing the new toilet.
Installsucientbackingbehindthenishedwalltoprovideasecure
material for the anchoring devices.
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t hesitate to
contact us.Ourphonenumbersarelistedonthebackcover.Thanksagain
forchoosingKohler Company.

Kohler Co. 3 1102602-A2-H
Pan Installation
2 Dene the position of connector: Place the connector onto the pan, position
between outlet and waste pipe.
3 Mark the positions of the oor xing kit holes.
Use the template (if supplied)
Waste Pipe
Waste Pipe
A
B
Connector to Wall Connector to Wall
Wall
Wall
Case1 Case2
Finished
Wall
Finished
Wall
Pan
Connector
Waste Pipe
Connector
Waste Pipe
Connector
Setout
Pan
Setout
Case 3 Finished
Wall
Connector
Waste Pipe
Connector
Pan
Setout
Offset Pan Collar
1 Remove the existing toilet: Turn o the water supply and ush the toilet, then
sponge out all remaining water from the cistern. Disconnect the supply shut-o
valve (if present), and remove the old pan and cistern.
CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately,
temporarity stu a rag in the closet ange. Ensure this is removed befor installing
the new toilet

1102602-A2-H 4 Kohler Co.
4.1 With Bracket
Drill 10 mm xing holes at the marked locations on the oor and insert the
anchor. Place a washer onto each of the hexagon screws and insert them in
the brackets. Fix the brackets to the oor. Position the toilet in the marked
position. install the sleeves using screws x the toilet to the brackets. Aach
the caps to the screw heads.
4 Floor xing - 2 methods
4.2 With Screw Only
Place the toilet into the desired position. place the protective plastic sleeve
onto the drill bit and, using the anchoring holes in the toilet as your guide,
drill 8 mm xing holes in the oor. place the anchors into the xing holes
through the toilet. Using the screws x the toilet to the oor. aach the caps
to the screw heads.
Anchor
Screw
Sleeve
Hole
Cap
Hexagon
Lag Screw
Bracket
Washer
Anchor
Screw Cap
Screw
Anchor
Sleeve
Drill

Kohler Co. 5 1102602-A2-H
Cistern Installation
1 Cistern information.
MIRAGE
Inlet Valve
Flush Valve
Optional Bottom Water Inlet Kit
148794A-NA for use on
OPIAZ
PARLIAMENT
PERSUADE
ESCALE
REACH
Stop Valve
Cistern Hose
OVE
PANACHE
OPIAZ
PARLIAMENT
PERSUADE
ESCALE
REACH

1102602-A2-H 6 Kohler Co.
Seat Installation
3 Connect the supply shut-o valve to the supply hose and connect supply hose
to toilet supply shank.
1 Install the seat as per the supplied
seat instructions.
2 Position the cistern on the pan by centering the gasket on the pan inlet. Ascemble
the retaining and sealing washer to the screw. Securely tighten the screw so the
cistern is level.
Screw
Plan Washer
Sealing Washer
Nut
Plastic Nut
Gasket
Screw
Retaining Washer
Plan Washer
Fiber Washer
Sealing Washer
Screw
Brass*
* Optional for different product
Brass*
Water
Supply
Hose
Water Supply Hose
(Not supplied)
Rear Inlet TypeBottom Inlet Type

Kohler Co. 7 1102602-A2-H
Push Button Installation
1 Disassemble the push rods. 2 Using the push rod, measure the
distance between the ush valve and
the top of the cistern lid. Mark this
lengh and cut the push rod to length.
Cut the push rod to length.
3 Reassemble the push rods. 4 Fit the lid and test the buons. Adjust
the rods as required.

1102602-A2-H 8 Kohler Co.
Flush Valve Removal and Installation
2 Assembly ush valve by pushing
straight down into the canister and
turning left.
Flush Valve B
1 Release ush valve by squeezing
the tabs on both side of the canister
and pulling straight up out of the
ush valve.
2 Assembly ush valve by pressing it
into the ush valve so it snaps into
place.
Flush Valve A
1 Release ush valve by turning righ
and pull straight up on the canister.
1
2
1
2

Kohler Co. 9 1102602-A2-H

1102602-A2-H Kohler Co.