Kohler 22572T-9 User manual

1332564-2A-B 1
INSTALLATION INSTRUCTIONS
PARALLEL
Turn diverter handle clockwise for bath spout, turn counter-clockwise for handshower, middle position for both.
Press the buttons of the handshower to change the water flow.
ROUGH-IN DIMENSIONS
HANDLE OPERATION
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Shut off the main water supply.
2. Carefully read entire instructions before beginning installation.
3. Observe local plumbing codes.
4. This faucet has switching function only. It must work with a bath faucet (purchased separately) that has both
on/off and hot/cold mixing control.
5. The highest working pressure for handshower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer
is needed. The highest water and environment temperature is 60ºC. Please keep handshower, showerhead and
shower arm away from heater, or it may become damaged and cause injury to the user.
BEFORE YOU BEGIN
22572T-9 Deck Mount Diverter And Handshower
22
182 43
240
208
Ø28
45º
Ø28
60×60 60×60
2000
1000
1000 600
200 Min.
50 Max.
Ø30~Ø35 Ø33~Ø40
G1/2˝ G1/2˝
G1/2˝
G1/2˝
G1/2˝

1332564-2A-B 2
21
14
15
20
16
17
18
19
22
23
24
25
26
INSTALLATION
How to Install the Diverter Body
Pre-install the screws(10) into the screw
holes of the threaded ring(9). Install the
threaded ring, steel washer(8) and fiber
washer(7) on the shank(11). From
underside of the bathtub, install the diverter
assembly(12) into the mounting hole.
Put the O-ring(6) into the groove of the
nut(5). Tighten the nut onto the shank from
upside of the bathtub. Secure the diverter
assembly by tightening the screws(10).
NOTE: The end with check valve(13) in
diverter is connected to shower hose.
Press the handle kit(3) onto the nut. Position
the handle base(4) as shown. Tighten the
screw(2) by hex wrench(1).
How to Install the Handshower
Pre-install the screws(19) into the screw
holes of the threaded ring(20). Install the
threaded ring, steel washer(18) and fiber
washer(17) on the shank(16). From
underside of the bathtub, install the shank
into the mounting hole as shown.
Put the O-ring(15) into the groove of the
escutcheon(14). Tighten the escutcheon
with O-ring on the shank. Tighten the
screws(19) firmly.
Put the washer(25) into the shower hose
(26, length: 2000mm). Connect the shower
hose to the elbow assembly(24) firstly.
Then slide the shower hose through the
escutcheon and shank.
Put the screen washer(23) into the elbow
assembly. Put the restrictor(22) into the
handshower(21) if needed. Connect the
elbow assembly to handshower.
3
4
2
1
6
7
8
9
11
10
12 13
5

1332564-2A-B 3
22572T-9 Deck Mount Diverter And Handshower
1332564-2A-B 6
PARALLEL
SERVICE PARTS
**Color code must be specified when ordering.
How to Connect the Hose
Way 1: Work with single handle deck mount bath faucet 23498T-4 or other single handle
deck mount bath faucet
Connect one end of the hose(28, length: 1000mm) to the valve kit connector of 23498T. Remove the hose
provided with deck mount faucet 23498T and put it away. Connect the other end to the bottom port of the diverter.
Connect one end of the hose(29, length: 600mm) to the shower hose(26, length: 2000mm). Connect the other end
to the shower end(the end with check valve(13)) of the diverter.
Connect one end of the hose(27, length: 1000mm) to the bath spout. Connect the other end to another end of
diverter.
27
28
13
29
26
897637**
836316
75100-58
1332549**
22352
1110332
831587
3029882
834428
1297467**
77420
1030624
1240266
880010
831587
1046290
832751 1332559**
1332555
1010167
22352
1110332
3029882
834683
1332558
1173737
1137478-RP
1007995
831752
833226
833226
78125
1332556
864718
831289
831289
864149-CP
3002770
3002771 871527
AF:1368618-ACP
BN:1368618-BCP
BL:1368618-LCP
RGD:1368618-RCP
CP & Others:898324**

1332564-2A-B 4
1332564-2A-B 5
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION CHECKOUT
Ensure all coupling nuts are tight. Turn on main water supply and check for leaks. Repair as required.
CLEANING INSTRUCTIONS
How to Maintain the Handshower
Any debris or mineral build-up may cause
the flow stream distorted or reduce the flow
rate. To remove the debris or mineral
build-up, run water through the handshower,
firmly press or rub your finger back and forth
across the rubber nozzles.
Remove and clean the screen washer.
Way 2: work with dual handle deck mount bath faucet
Put the washer(30) into the nut(32) of the tee(31). Then connect the tee(31) to one side body(33) of the deck mount
bath faucet.
Put the fiber washer(34) into the nut(35). Tighten the nut to one of the ports of the center tee(36) for the spout.
Connect one side body(37) and tee(31) on another side body with hose(28, length: 1000mm).
Connect the tee(31) and bottom port of the diverter with one of the hoses provided with deck mount faucet(Remove
another hose and put it away). Connect the shower hose(26, length: 2000mm) and shower end(the end with check
valve(13)) of the diverter with connection hose(29, length: 600mm).
Connect the center tee(36) and another end of the diverter with hose(27, length: 1000mm).
To ensure the water flows smoothly and the handshower can be drawn out easily, the hose should avoid kinking,
twisting. To ease installation, you may back off tee of the spout up to 180 degree. NOTE: Hoses should be only
used where indicated.
27
29
26
13
36
34
35
37 33
30 32
31 28