Kohler K-8297TW-HC-0 User manual

KOHLER CHINA INVESTMENT CO., LTD
NO.158, JIANG CHANG SAN ROAD, JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436
SHANGHAI KOHLER ELECTRONICS CO.,LTD.
NO.1955, FENG XIANG ROAD, BAO SHAN DISTRICT, SHANGHAI, PRC POST CODE: 200444
158 200436
1955 200444
安裝說明
Smart Seat
C3電腦馬桶便座
台灣專用
English page 2-7
中文頁碼8-17
1383630-A01-B

WARNING: Risk of electric shock, fire or personal injury. This
product must be installed safely.
Min water pressure 0.07MPa (dynamic pressure)
Max water pressure 0.74MPa.
When install the product in the room, a stop valve shall be installed in a close
proximity. For emergency circumstances, the water inlet valve shall be stopped
without using any tools; otherwise unexpected failure may cause the loss to the
customer.
1383630-A01-B
2
Kohler Co.

Warning: Risk of electric shock, fire or personal injury.
This product must be installed safely.
140mm
20mm
70mm
Kohler Co.
3
1383630-A01-B

Gasket
Insert screw into gasket separately.
Gasket
Gasket
Snap screws into mounting board and toilet mounting holes, move
washer so to snap into the mounting board groove. Pay attention to
the washer direction: bending side upwards for washer close to
hole.
Place each screw into washer, pay attention to the washer direction:
bending side upwards for washer close to the hole.
1383630-A01-B
4
Kohler Co.

Arrow 2
Arrow 1
Arrow 1
Mounting
plate
Slightly lift cover front tip, observe rear bugle slot, guide mounting plate into
the groove (per arrow 1 direction) Align the slot on the mounting plate with the
groove located below the toilet seat.
Slide the seat onto the mounting plate, front tip downwards (per arrow 2
direction) until you feel it snaps into place.
For Toilets without Threaded Inserts:
To adjust cover position, do not remove cover; only loosen screws to adjust
cover and mounting plate position. Tight down the bolts when desired position
is acquired.
For Toilets with Threaded Inserts:
To adjust cover position, remove cover first, readjust mounting plate position.
Once the mounting plate is confirmed, tighten screws, fasten mounting plate,
re-install cover.
Kohler Co.
5
1383630-A01-B

Connect T-valve to water supply system (valve shall be purchased by
customer).
Water tank inlet hose
Bidet seat inlet hose
Please use new hose enclosed with tools. Please do not reuse
the old hose.
Remove the orange rubber cap of Bidet inlet valve.
1383630-A01-B
6
Kohler Co.

Ensure if water inlet valve is OPEN.
Kohler Co.
7
1383630-A01-B

警告：触电、火灾或人身伤害的危险。本产品必须安全接地。
最小進水壓力0.07MPa（動壓）
最大進水壓力0.74MPa。
在安裝本產品的同一房間中，需要在觸手可及的位置安裝一個止水閥，
用於緊急情況下，無需借助工具即可切斷本產品的進水水路；否則本產品
的意外故障可能會導致使用者損失。
1383630-A01-B
8
Kohler Co.

140mm
20mm
70mm
警告：触电、火灾或人身伤害的危险。本产品必须安
全接地。
Kohler Co.
9
1383630-A01-B

把每個螺絲分別插入墊圈內，注意墊片方向：墊片近孔彎折處向上。
移動墊圈，使之卡在安裝板的凹槽
內，注意墊片方向：墊片近孔彎折處向上。
墊片
墊片
墊片
墊片。
1383630-A01-B
10
Kohler Co.